Question about 1992 Buick LeSabre

1 Answer

Hit on right rear at wheel well, wheel pushed in at top what could be the problem?????thanksComment posted on May 11, 2200+9-

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

I don't understand your question fully (Hit?). If you were involved and a collision and your tire rubs on the fender, get the fender fixed ASAP! Tires can get peeled like a banana if they come into contact with any sharp piece of metal, and if its rubbing on the inner fender, then friction heat caused by this can cause the tire become weak in that area and subsequently blow out.... If that is not the problem, or case then her are more causes for tires rubbing...

Tires "Out of Alignment", non-factory rims and/or tires, wrong size,width, rim "off-set" etc., suspension coil springs and. or shocks (car sitting lower than usual), twisted chassis due to accident or other impacts

Posted on May 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I reset TPMS light focus 14


Use this if you're installing winter wheels/tires that have sensors already installed, or even if you are just doing a tire rotation. Not sure if this has been posted before. I tried searching but didn't see it posted anywhere. No need to go and buy the TPMS learning tool.

1) Make sure your tiresare inflated to the recommended psi. Mine is 40psi.

2) Turn ignition to the on position. If you have a push button start, push the start button without pressing the brake pedal.

3) Push the hazard light button 6 times. The horn should honk and you should see "Train left front tire" in the LCD display between the tach and speedo.

4) Release air pressure in the front left tireuntil you hear the horn honk. The LCD display should now read "Train right front tire".

5) Release air pressure in the right front tire until you hear the horn honk.

6) Repeat for the the right rear tire, and then the left rear tire.

7) You should now see "Training Complete" in the LCD display.

8) Fill your tiresback up to the recommended pressure.

Enjoy!

Nov 19, 2014 | Cars & Trucks

1 Answer

2001 altima replacing rear wheel stud


strip it down to your hub the hub holds the studs .it is a push pull fit .but an old nut on it.then hit the top of it .it when then push in.remove the nut. push in the new stud from the rear of the hub.put a larger nut on top of stud ,then your wheel nut to pull the stud into the hub.then remove the wheel nut .then refit the parts taken off.and fit your wheel.

Dec 30, 2013 | 2005 Chrysler PT Cruiser

1 Answer

Mercedes c 200 n/s rear wheel hits wheel arch i curbed it ever since ive had that problem


if its touching the arch could be a few things if its been curbed broken spring weel shock absorber worst case pulled the bearing out sligtley or any one of the arms going from subframe could be bent or broken it shouldn't be putting it self right when it gets bumped again I would be carful as you could loose the wheel eventually would start with checking the rear wheel bearing and hub also get the rear lower bushing checked as I said could be anything hope this helps ivan

Mar 21, 2013 | Mercedes-Benz C-Class Cars & Trucks

1 Answer

What is broken after the collision


you bent the lower control arm and sounds like the inner and outer tir rods

Oct 29, 2012 | Hyundai Motor 2003 Elantra

1 Answer

Rear brake drum remov al on ford windstar


after removing the tire, the rear hub should come right off, if not then grab it and shake it from side to side, if it seems to be stuck, you can take a 3 - 4 pound hammer or rubber mallet, and hit it fairly lightly in the top, bottom, and sides, this should free it up, if not, the brake adusting wheel will have to be loosen, this is by going into the back of the drum, normally where a small rubber plug about 1" - 1 1/2" long is inserted at the bottom, remove the plug, and take a brake adjusting tool and reach through the hole to the star adusting wheel, and turn it , i believe you have to turn it downward to get it to loosen up, if it doesn't free, then turn it in the opposite direction, remember that the adusting wheel is always in the opposite position on the brake asssembly on the opposite rear wheel.

Feb 15, 2011 | Ford Windstar Cars & Trucks

1 Answer

How do you adjust the brake shoes on the Hilux 1985-1994 Toyota Pickup


I am assuming you are speaking of the rear brakes. If that is the case, then it is not hard to adjust. Jack up the rear of vehicle and remove back wheels. This can be done one at a time or you can remove both wheels at same time. There should be a hole in the drum near the top. Insert a flat blade screwdriver into hole and push down. It should be resistance when pushing. Or, you can put the vehicle in reverse and back up about 50 yards and hit the brakes hard. Do that a couple of times.

Feb 15, 2010 | Toyota Pickup Cars & Trucks

1 Answer

1999 Chevy Silverado with clunking/jerking in the back


It sounds like your 4WD is still engaged and you need to have it serviced. It's common for the 4wd to get stuck in the on position with the button pushed to the 2wd mode. As you turn the front wheels are binding with the rear wheels. There is a vacuum switch on top if the transfer case on the drivers side that may have gone bad and needs to be replaced. You can pick it up at Auto Zone for $25.00 and $85.00 at the dealer, there is three vacuum hose attached to it that needs to be disconnected and then the switch can be un screwed from the transfer case like a spark plug.. Good luck and hope this helps. keep me posted, be glad to answer any question you may have. 

Jul 13, 2009 | 2000 Chevrolet Silverado 1500

4 Answers

Unbearable humming vibration in rear of car


It sounds like one of your rear wheel bearing hub has gone bad and needs to be replaced before you lose your wheel. I am thinking to pay attention to the right rear wheel hub bearing than needs to be replaced, they go for around $170.00 at Auto Zone and they can give you the step by step instructions to get the job done with common tools or you can use there loner program if you need to borrow a tool you may not have. With the car parked walk to the rear wheels and push and pull on the top of the tire (Side to side), feel and listen for any play. You should not hear or feel any play at all unless the wheel hub has gone bad. It take less then 1-1/2 hour to change the wheel hub and less if your good with tools. Good luck and keep me posted friend. Be safe.

Jul 06, 2009 | 2005 Ford Focus

1 Answer

My 2005 Impala is making a roaring sound when I turn into a curve driving....What does this mean and how can it be fixed??


It sounds like one of your wheel bearing needs to be replace, most likely one of the rear bearing may have gone dry and needs to be replaced soon as possible before you have a total bearing failure and loose a wheel. With the car parked, go to each wheel and push back and forth on the top (side to side) you should be able to hear and feel which wheel has the play since it's will feel and sound different from the other wheels. The rear wheel bearing can be replaced with simple tool and under 1 hour if your good with tools and the front will have to be brought to a shop since your going to need am impact gun to remove the front axle nut from the wheel hub. Good luck and hope this helps. Keep me posted if your going to replace the rear wheel hub your self and i can give you the instructions to replacing the hub. I believe the rear hubs goes for around $170.00 at Auto Zone and they can give you the step by step instructions too. 

Jul 06, 2009 | Chevrolet Impala Cars & Trucks

2 Answers

Rear wheel noise


Brakes or bearing would be my two top choices as starters.

May 07, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
1992 Buick LeSabre Logo

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...