Question about 1991 Ford Bronco

1 Answer

I don't think the module is working, I can't find it.

The shift module has a self test light on it. But I don't know where it is?

The truck has the 402 v8 in it.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 2,559 Answers

It is the Power control module,located behind the side kick panel in the passenger side floor board.

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

04 s10 wont go into 4wd hi 4wd lo works


Does your vehicle have three or four button shift switch ?
The NVG 236 transfer case features a 4 button shift control switch located on the instrument panel.
OR
The NVG 233 transfer case features a 3 button shift control switch,
The transfer case shift control module is equipped with the ability to store diagnostic information, which is useful to a technician in the event of module, component or wiring failures. This information can be retrieved from the transfer case shift control module by way of flash codes, which are displayed on the three transfer case shift control switch buttons. These buttons are located on the instrument panel to the right of the steering wheel Before obtaining DTCs, perform the following transfer case control module (TCCM) Self-Test.
TCCM Self-Test
Observe the transfer case shift control switch indicators while turning the ignition switch to RUN. A properly operating system will flash all indicators and then will return to the current gear. If the system is operating normally, then proceed to Displaying Codes.
If the TCCM failed the Self-Test, then test the following circuits.
• Battery Positive Voltage (40 and 1640), and Ignition 3 Voltage for battery voltage
• Ground Circuit for ground
• Diagnostic enable circuit for an open or high resistance
• Transfer case shift control switch connector
If the above circuits are normal but the TCCM still fails the Self-Test, replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .

DTC Displaying
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes. Refer to Diagnostic Trouble Code (DTC) List .
Important: If the transfer case shift control switch buttons all blink only once and then stop, no fault codes are stored in the transfer case shift control module.
• When one DTC is stored in memory, that code will blink that number of times followed by a 3 second pause and then repeat.
• If more than one code is stored, the first code will blink, followed by a 3 second pause and then the second code will blink.
• This sequence will continue until PIN 13 on the DLC is no longer grounded.
• If the TCCM will not communicate the presence or absence of DTCs, test the above circuits in Self-Test Step 2. If the circuits are complete, then replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .

The four button switch system is a bit more complex ,need a factory scanner or professional one to check DTC'S

DTC B2725
DTC C0300
DTC C0305
DTC C0308
DTC C0309
DTC C0310
DTC C0315
DTC C0323
DTC C0324
DTC C0327
DTC C0362
DTC C0367
DTC C0374
DTC C0376
DTC C0387
DTC C0550
DTC C0611
this is where you should start ,checking code's .

Dec 24, 2017 | Cars & Trucks

1 Answer

Service 4x4 light is on...2000 gmc jimmy...replaced the switch on dash but nothing works..what is my next step to fix issue?


Two speed automatic or is it two speed selectable ? Either case the first thing would be have it check for DTC'S - diagnostic trouble codes . Both are computer controlled .
DTC B2725 ATC Mode Switch Circuit Malfunction
DTC C0300 Rear Speed Sensor Malfunction
DTC C0305 Front Speed Sensor Malfunction
DTC C0308 Motor A/B Circuit Low
DTC C0309 Motor A/B Circuit High
DTC C0310 Motor A/B Circuit Open
DTC C0315 Motor Ground Circuit Open
DTC C0323 T-Case Lock Circuit Low
DTC C0324 T-Case Lock Circuit High
DTC C0327 Encoder Circuit Malfunction
DTC C0362 4LO Discrete Output Circuit High
DTC C0367 Front Axle Control Circuit High
DTC C0374 General System Malfunction
DTC C0376 Front/Rear Shaft Speed Mismatch
DTC C0387 Unable to Perform Shift
DTC C0550 ECU Malfunction
DTC C0611 VIN Information Error

This for the two speed selectable
The transfer case shift control module normally has battery voltage supplied to it at all times through the battery positive voltage circuit (CKT 40). When the ignition is ON, the transfer case shift control module conducts a self-test to determine if it retains the same memory it had when the ignition was last turned OFF. This self-test indicates whether the RAM standby power supply to the transfer case shift control module pin C6 was interrupted, which would result in clearing DTC's from memory. If the self-test fails the transfer case shift control module sets DTC 1.

You can check codes without a scan tool on this two speed selectable system . Do you know what the DLC is ? Under the steering wheel , connector to plug a scan tool into ?
Important: Check the transfer case shift control module for DTCs. The transfer case shift control module is not a class 2 device. DTCs are displayed on the transfer case shift control switch. Use the following four steps to obtain DTCs.
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes.
DTC 001
DTC 002
DTC 003
DTC 004

Dec 30, 2016 | GMC Cars & Trucks

1 Answer

I own a 02 foard explorer shift motor was bad i think and i removed it, i started it to relocate it, installed the new shift motor


Don's 1999 Ford Ranger shift motor PROBLEM SOLVED ...

? 13:05
https://www.youtube.com/watch?v=wcn39gwPWfI
Oct 1, 2013 - Uploaded by gtarman49
Don's 1999 Ford Ranger shift motor PROBLEM SOLVED. ...How to find replace fix 4x4 transfer case shift module 2002 Ford Explorer 4 wheel ...

How To Install Replace 4x4 Transfer Case Shift Motor Ford ...

? 9:15
https://www.youtube.com/watch?v=9ldrtZODxQ8
Oct 26, 2010 - Uploaded by 1A Auto Parts
How To Install Replace 4x4 Transfer Case Shift Motor Ford Explorer .... transfer case shift module 2002 Ford Explorer 4 wheel drive not working ...

How to find replace fix 4x4 transfer case shift module 2002 ...

? 3:07
https://www.youtube.com/watch?v=sZw3SS2Pt-4
Nov 3, 2013 - Uploaded by kirk colombo
... transfer case shift module 2002 Ford Explorer 4 wheel drivenot working ..... I replaced the transfer motor so i think it is the control module.


Jan 08, 2016 | Cars & Trucks

1 Answer

Stuck in 4 wheel Drive High but no lights are lit


Hi Jimi , There are very specific diagnostic procedures to follow for diagnosing this system. First a good visual inspection of the transfer case an fluid level an wiring connections. The transfer case shift control module is equipped with the ability to store diagnostic information, which is useful to a technician in the event of module, component or wiring failures. This information can be retrieved from the transfer case shift control module by way of flash codes, which are displayed on the three transfer case shift control switch buttons. These buttons are located on the instrument panel to the right of the steering wheel Before obtaining DTCs, perform the following transfer case control module (TCCM) Self-Test.
TCCM Self-Test
  1. Observe the transfer case shift control switch indicators while turning the ignition switch to RUN. A properly operating system will flash all indicators and then will return to the current gear. If the system is operating normally, then proceed to Displaying Codes.
  2. If the TCCM failed the Self-Test, then test the following circuits.
  3. ?€¢
    Battery Positive Voltage (40 and 1640), and Ignition 3 Voltage for battery voltage


    ?€¢
    Ground Circuit for ground


    ?€¢
    Diagnostic enable circuit for an open or high resistance


    ?€¢
    Transfer case shift control switch connector

  4. If the above circuits are normal but the TCCM still fails the Self-Test, replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .
DTC Displaying
  1. Turn OFF the ignition for 10 seconds.
  2. Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
  3. Turn ON the ignition, with the engine OFF.
  4. Observe the transfer case shift control switch select buttons for flashing codes. Refer to Diagnostic Trouble Code (DTC) List .
Important: If the transfer case shift control switch buttons all blink only once and then stop, no fault codes are stored in the transfer case shift control module.
?€¢
When one DTC is stored in memory, that code will blink that number of times followed by a 3 second pause and then repeat.


?€¢
If more than one code is stored, the first code will blink, followed by a 3 second pause and then the second code will blink.


?€¢
This sequence will continue until PIN 13 on the DLC is no longer grounded.


?€¢
If the TCCM will not communicate the presence or absence of DTCs, test the above circuits in Self-Test Step 2. If the circuits are complete, then replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .


Let me know if you have any codes , I have code definitions an procedures.

Feb 04, 2015 | 2003 GMC Sonoma Extended Cab

1 Answer

I have a 1998 Chevy Tahoe I tryed to put my truck is 4wd low and it tryed and keep on blinking and went back to 2wd and blow a fuse and I tryed again and did it again but then the the service 4wd light...


Which 4X4 system does your tahoe have ?
Transfer Case System Description (Selectable 4WD)
The New Venture Gear Model NV243 is an electronically controlled optional transfer case for use on four wheel drive K trucks. The driver selects 2HI, 4HI, or 4LO by pushing one of three illuminating shift select buttons mounted on the instrument panel. The shift select buttons display the transfer case mode and range, self-test, diagnostic trouble codes, and electronic shift mechanical engaging problems.

Transfer Case System Description (Automatic 4WD)
The two speed Auto transfer case system utilizes a part time front axle. The system allows the driver to select the transfer case position with a touch of a button. The following positions can be selected: 4-wheel drive high range (4H), All Wheel Drive (AUTO), 2 Wheel Drive high range (2H), Neutral (N), and 4-Wheel Drive low range (4L).
The Auto Transfer Case (ATC) Control Module controls all the shifting action of the transfer case based on input from the driver as well as information from the Vehicle Control Module (VCM) /Powertrain Control Module (PCM).
4WD (4H or 4L) mode: This is accomplished by engaging the front axle, applying PWM to an electric motor to apply maximum torque, (fully compressing the transfer case clutch plates) to the front axle, then removing the ground on circuit 1569, thus locking the motor in position and stop the PWM to the motor.
AUTO mode: When in this mode of operation, the system should engage the front axle, then it monitors the front and rear propshaft speeds for any speed differences. When the system senses rear wheel slip, a difference of propshaft speed between front and rear, the Auto Transfer Case (ATC) Control Module will use pulse width modulation (PWM) to drive an electric motor. This motor transfers only the required torque to the front wheels to gain additional traction on slippery surfaces up to 75 mph. There is no torque applied to the front wheels until the module senses rear wheel slip.
Throttle anticipation (only operational when in AUTO mode): If the vehicle is below 5 mph and the accelerator is pressed quickly beyond a set point, the system will automatically transfer a percentage of torque to the front wheels to help prevent the rear wheels from slipping, as in a hard acceleration from a stopped position.
The Auto Transfer Case (ATC) Control Module also has the capability of engaging the front axle while the vehicle is in motion. It does this by applying PWM to the electric motor to apply torque to the front axle, this action is used to match the speed of the front and rear propshafts. After the module senses the proper speed, it then supplies a ground on circuit 1570 to engage the front axle.
The Auto Transfer Case (ATC) Control Module will accept a mode shift only when the engine is running and a valid Motor/Encoder signal is present. A mode shift is any shift between 2H, 4H, and AUTO.
The Auto Transfer Case (ATC) Control Module will permit a range shift only if the following conditions are met within 30 seconds of the request:

Automatic 4WD Diagnostic Aids
A Scan Tool reads and displays the following information:
• Diagnostic Trouble code(s)
• Code status bit (are codes set or not)
• Transfer case lock status
• Lamp in the switch/lamp assembly
• Motor/Encoder gear position
• Ignition (3) voltage
• Front propshaft speed sensor (KPH)
• Front axle switch (open/closed)
• Front axle requested position (engaged/disengaged)
• Rear propshaft speed sensor (KPH)
• Mode switch position request
• Park switch (open/closed)
• 4WD (Adapt) Mode Auto bit
• Current Mode corrective action PWM
• Average and highest PWM applied during last slip recovery event
• Throttle anticipation mode
• Average and highest PWM applied during last Throttle anticipation corrective action event
• Difference between front and rear propshaft RPM
• Adapt event counter
• Throttle position sensor percentage

Check the transfer case shift control module for DTC's. The transfer case shift control module is not a class 2 device. DTC's are displayed on the transfer case shift control switch. Refer to Diagnostic Trouble Code (DTC) Displaying .
Are any DTC's present?
Diagnostic Trouble Code (DTC) Displaying
The transfer case shift control module is equipped with the ability to store diagnostic information, which is useful to a technician in the event of module, component or wiring failures. This information can be retrieved from the transfer case shift control module by way of flash codes, which are displayed on the three transfer case shift control switch buttons. These buttons are located on the instrument panel to the right of the steering wheel Before obtaining DTCs, perform the following transfer case control module (TCCM) Self-Test.
TCCM Self-Test
Observe the transfer case shift control switch indicators while turning the ignition switch to RUN. A properly operating system will flash all indicators and then will return to the current gear. If the system is operating normally, then proceed to Displaying Codes.
If the TCCM failed the Self-Test, then test the following circuits.
• Battery Positive Voltage (40 and 1640), and Ignition 3 Voltage for battery voltage
• Ground Circuit for ground
• Diagnostic enable circuit for an open or high resistance
• Transfer case shift control switch connector
If the above circuits are normal but the TCCM still fails the Self-Test, replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .
DTC Displaying
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes. Refer to Diagnostic Trouble Code (DTC) List .
Important: If the transfer case shift control switch buttons all blink only once and then stop, no fault codes are stored in the transfer case shift control module.
• When one DTC is stored in memory, that code will blink that number of times followed by a 3 second pause and then repeat.
• If more than one code is stored, the first code will blink, followed by a 3 second pause and then the second code will blink.
• This sequence will continue until PIN 13 on the DLC is no longer grounded.
• If the TCCM will not communicate the presence or absence of DTCs, test the above circuits in Self-Test Step 2. If the circuits are complete, then replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .

Apr 15, 2017 | Cars & Trucks

1 Answer

99 chevy suburban how do i know my tccm has power


Do you have a wiring diagram for TCCM ?
The transfer case shift control module is equipped with the ability to store diagnostic information, which is useful to a technician in the event of module, component or wiring failures. This information can be retrieved from the transfer case shift control module by way of flash codes, which are displayed on the three transfer case shift control switch buttons. These buttons are located on the instrument panel to the right of the steering wheel Before obtaining DTCs, perform the following transfer case control module (TCCM) Self-Test.
TCCM Self-Test
Observe the transfer case shift control switch indicators while turning the ignition switch to RUN. A properly operating system will flash all indicators and then will return to the current gear. If the system is operating normally, then proceed to Displaying Codes.
If the TCCM failed the Self-Test, then test the following circuits.
• Battery Positive Voltage (40 and 1640), and Ignition 3 Voltage for battery voltage
• Ground Circuit for ground
• Diagnostic enable circuit for an open or high resistance
• Transfer case shift control switch connector
If the above circuits are normal but the TCCM still fails the Self-Test, replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .

Do you know how to test automotive electrical circuit's ? How to use a DVOM - digital volt ohm meter ? Free wiring diagrams here
http://www.bbbind.com/free_tsb.html
Enter vehicle info. year , make , model and engine size . Under system click on driveline/Axle ,then under subsystem click on transfer case controls . Click the search button then the blue links . Do you know where the TCCM lives ? Check all power and ground's . If all are good , replace the TCCM .

Dec 12, 2017 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

I have a 1998 Chevy Blazer 4dr. The 4 whl drive switch does not light up. Some how the 4 whl drive got ingaged and now it is stuck there. I have a new switch on order but this is getting ridiculous. When...


The New Venture Gear Model NV233 is an electronically controlled optional transfer case for use on four wheel drive T trucks. The driver selects 2HI, 4HI, or 4LO by pushing one of three illuminating shift select buttons mounted on the instrument panel. The shift select buttons display the transfer case mode and range, self-test, diagnostic trouble codes, and electronic shift mechanical engaging problems.
During normal driving the transfer case is in the 2HI mode. When the transfer case is in the 2HI mode. When the transfer case is in 2HI both the 4HI and 4LO switch circuits are open, and both lights are OFF. When the four-wheel drive shift select button has been pressed, the four-wheel drive indicator lamp under the sift select button turns ON when the front axle has engaged. The shift select button will blink while the front axle is engaging. This is a normal condition.
The shifting of the transfer case is performed by a motor/encoder that receives drive signals from the transfer case control module (TCCM). When the driver selects one of the transfer case shift select buttons, request signals are sent to the TCCM. If the correct input signals exists, the TCCM will send drive voltages to the motor/encoder. The motor/encoder will position the transfer case to the ordered shift position.

Transfer Case Control Module Description
The TCCM performs the following functions:
• Receives input signals
• Processes the signal information
• Develops output signals
• Sends the output signal in order to control the shifting of the transfer case
The TCCM receives input signals from the following sources:
• The transfer case shift select buttons
• The NSBU switch on the vehicles with automatic transmissions
• The clutch position switch on the vehicles with manual transmissions
• The vehicle sped sensor calibrator module
• The encoder/motor range and the mode feedback signals
• The diagnostic enable
• The front axle mechanical status signal
In order to ensure the electronic shift system is operating properly, the transfer case control module (TCCM) continually performs diagnostics checks on itself and other parts of the electronic shift system when the ignition switch is in the run position. The following are different types of system checks that the TCCM continually performs.
Data Memory Retention Check
The TCCM checks the stored diagnostic trouble code memory to see if the memory has changed since the ignition switch was last positioned to OFF. This self test checks in order to see if the RAM standby power supply has been interrupted. If the TCCM detects a RAM standby power supply interruption, (the loss of stored diagnostic trouble code) the TCCM stores a DTC of 1 indicating RAM standby power failure.
This condition occurs when the TCCM is disconnected from the wiring harness or battery power is removed. The DTC of 1 automatically clears from the TCCM after cycling the ignition switch ON and OFF five times.

Before replacing parts you should test the system !
Diagnostic Trouble Code (DTC) Displaying
The transfer case shift control module is equipped with the ability to store diagnostic information, which is useful to a technician in the event of module, component or wiring failures. This information can be retrieved from the transfer case shift control module by way of flash codes, which are displayed on the three transfer case shift control switch buttons. These buttons are located on the instrument panel to the right of the steering wheel Before obtaining DTCs, perform the following transfer case control module (TCCM) Self-Test.
TCCM Self-Test
Observe the transfer case shift control switch indicators while turning the ignition switch to RUN. A properly operating system will flash all indicators and then will return to the current gear. If the system is operating normally, then proceed to Displaying Codes.
If the TCCM failed the Self-Test, then test the following circuits.
• Battery Positive Voltage (40 and 1640), and Ignition 3 Voltage for battery voltage
• Ground Circuit for ground
• Diagnostic enable circuit for an open or high resistance
• Transfer case shift control switch connector
If the above circuits are normal but the TCCM still fails the Self-Test, replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .
DTC Displaying
Turn OFF the ignition for 10 seconds.
Connect PIN 13 on the data link cable (DLC) to a ground. The DLC is located in the cab under the instrument panel on the driver's side.
Turn ON the ignition, with the engine OFF.
Observe the transfer case shift control switch select buttons for flashing codes. Refer to Diagnostic Trouble Code (DTC) List .
Important: If the transfer case shift control switch buttons all blink only once and then stop, no fault codes are stored in the transfer case shift control module.
• When one DTC is stored in memory, that code will blink that number of times followed by a 3 second pause and then repeat.
• If more than one code is stored, the first code will blink, followed by a 3 second pause and then the second code will blink.
• This sequence will continue until PIN 13 on the DLC is no longer grounded.
• If the TCCM will not communicate the presence or absence of DTCs, test the above circuits in Self-Test Step 2. If the circuits are complete, then replace the TCCM. Refer to Transfer Case Shift Control Module Replacement .

Is the 4WD fuse # 15 -10 amp located in the I/P fuse box good ?

Jul 30, 2017 | 1998 Chevrolet Blazer

1 Answer

Transfer case wont engage borg warner 13-56 electronic


if when you press the button to shift into 4 hi, all you hear are a lot of clicks from the control module under the glove box and no indicator lights, that could mean the actuator motor on the back of the t-case is warn(it has no braking ability) so it overshoots its position. this is a common problem. you can go under and hear the motor moving but it seems like it doesnt do anything. sense the module cant get the motor to stop in the correct position, it defaults all the way back to 2wd. a new tcase motor will fix that, you have to splice the wires into the 10 pin connector because from the factory i think 8 wires go to the motor/position sensor and 2 or 3 wires go to magnetic clutch and speed sensor. if there are no click when you press the button, i mean nothing happens, you can run a self diagnostic on the control module by turn the ingnition off, disconnecting the bottom 2 connectors of the 4x4 module (the top connector is the power supply dont touch that one) then turn key on and press the test button on the module (next to the red LED) if the LED lights up and stays on the module is bad. if you press the test button without disconnecting the bottom 2 connectors the led will light and stay on, this is normal and not an accurate self test. turn the key off before reconnecting the module. this advice is of course is assuming you already checked fuses, inspested ALL connectors in the circuit, especiall if a new tcase motor has already been spliced in some years ago, checked power at the switch and module and good grounds.

Aug 10, 2010 | 1995 Ford Bronco

1 Answer

Ford 2005 4x4 problem.


2-Speed Torque-On-Demand (TOD) Operation
The automatic 4-wheel drive (A4WD) system is a 2-speed torque-on-demand (TOD) operation that utilizes the following components:
  • Transfer case
  • 4-wheel drive (4WD) control module (integral to the powertrain control module [PCM])
  • Mode select switch (MSS)
  • Gearmotor encoder assembly (part of the transfer case shift motor)
  • Transfer case shift motor
  • Shift motor sense plate (part of the gearmotor encoder assembly)
Principles of Operation
Transfer Case Shift Motor The externally mounted transfer case shift motor, located at the rear of the transfer case, turns the shift cam assembly. As the shift cam assembly turns, it positions the reduction shift fork for desired transfer case operation. An integral position sensor in the shift motor provides shift motor position information to the 4WD control module.
Mode Select Switch (MSS) The push button MSS, mounted on the instrument panel, allows the operator to select the 4x4 Auto, 4x4 High, and 4x4 Low transfer case operating modes. The indicator light, on the instrument cluster push button, will illuminate only when the 4x4 Low position is engaged.
Visual Inspection Chart Mechanical Electrical
  • Axle shafts and CV joints
  • Driveshaft and universal joints
  • Fluid leaks
  • Matching tire sizes
  • Transfer case shift motor
  • Battery junction box (BJB) fuses:
    • 8 (30A)
    • 17 (5A)
    • 18 (20A)
  • Central junction box (CJB) fuses:
    • 12 (5A)
    • 24 (15A)
  • 4x4 module (PCM)
  • Wiring harness
  • Gearmotor encoder contact plate
  • Connector(s)
  • Circuitry
  • Mode indication switch (MSS)

  1. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.
  1. If the concern is not visually evident, connect the diagnostic tool to the data link connector and select the vehicle to be tested from the diagnostic tool menu. If the diagnostic tool does not communicate with the vehicle:
    • check that the program card is correctly installed.
    • check the connections to the vehicle.
    • check the ignition switch position.
  1. If the diagnostic tool still does not communicate with the vehicle, refer to the diagnostic tool operating manual.
  1. Carry out the diagnostic tool data link test. If the diagnostic tool responds with:
    • CAN circuit fault; all electronic control units no response/not equipped, refer to Section 418-00 .
    • No response/not equipped for 4WD module (PCM), Go To Pinpoint Test G .
    • System passed, retrieve and record the continuous diagnostic trouble codes (DTCs), erase the continuous DTCs and carry out the 4WD module (PCM) self test.
  1. If the DTCs retrieved are related to the concern, go to the 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index to continue diagnostics. 4WD Control Module (PCM) Diagnostic Trouble Code (DTC) Index
    DTC Description Source Action B1317 Battery Voltage HIGH 4WD Module (PCM) REFER to Section 414-00 . B1318 Battery Voltage LOW 4WD Module (PCM) REFER to Section 414-00 . B1319 Driver Door Ajar Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1322 Driver Door Ajar Circuit Short To Ground 4WD Module (PCM) Go To Pinpoint Test M . B1342 ECU is Defective 4WD Module (PCM) CLEAR the DTCs. REPEAT the 4x4 module (PCM) self test. If DTC B1342 is retrieved, INSTALL a new 4x4 module (PCM). REFER to Section 303-14 . CLEAR the DTCs. REPEAT the self test. B1483 Brake Pedal Input Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . B1485 Brake Pedal Input Short to Battery 4WD Module (PCM) Go To Pinpoint Test M . C1729 Transfer Case Unable to Transition Between 4H and 4L 4WD Module (PCM) Go To Pinpoint Test K . C1970 4WD Low Mode Switch LED Short to Battery 4WD Module (PCM) Go To Pinpoint Test K . C1971 4WD Low Mode Switch LED Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1707 Transfer Case NEUTRAL or PARK/NEUTRAL Indication Circuit 4WD Module (PCM) Go To Pinpoint Test M . P1812 Transmission 4-Wheel Drive Mode Select Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1815 Transmission 4-Wheel Drive Mode Select Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1816 Transmission NEUTRAL Safety Switch Circuit Failure 4WD Module (PCM) Go To Pinpoint Test M . P1819 Transmission NEUTRAL Safety Switch Circuit Short to Ground 4WD Module (PCM) Go To Pinpoint Test M . P1820 Transfer Case Clockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1822 Transfer Case Clockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1824 4-Wheel Drive Clutch Relay Circuit Failure 4WD Module (PCM) Go To Pinpoint Test H . P1826 4-Wheel Drive Low Clutch Relay Short Circuit to Battery 4WD Module (PCM) Go To Pinpoint Test H . P1827 4-Wheel Drive Low Clutch Relay Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test H . P1828 Transfer Case Counterclockwise Shift Relay Coil Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1830 Transfer Case Counterclockwise Shift Relay Coil Circuit Short To Battery 4WD Module (PCM) Go To Pinpoint Test K . P1849 Transfer Case Contact Plate A Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1853 Transfer Case Contact Plate B Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1857 Transfer Case Contact Plate C Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1861 Transfer Case Contact Plate D Short Circuit to Ground 4WD Module (PCM) Go To Pinpoint Test K . P1867 Transfer Case Contact Plate General Circuit Failure 4WD Module (PCM) Go To Pinpoint Test K . P1891 Transfer Case Contact Plate Ground Return Open Circuit 4WD Module (PCM) Go To Pinpoint Test K . U1900 CAN Communication BUS Fault 4WD Module (PCM) REFER to Section 418-00 . U2023 External Node Fault 4WD Module (PCM) REFER to Section 418-00 . U2051 One Or More Calibration Files Missing/Corrupt 4WD Module (PCM) Reprogram/Reflash the 4x4 module. REFER to Section 418-00 . - For All Other DTCs 4WD Module (PCM) REFER to Section 418-00 .
  2. Your best bet mite be to take it to a qualified repair shop !

May 30, 2017 | 2005 Ford Explorer

Not finding what you are looking for?
1991 Ford Bronco Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...