Question about 2006 Subaru Outback

1 Answer

2005 Nissan Quest Automatic Liftgate won't open.

When I use the key fob, or the interior open/close button, the liftgate opens about 1 inch, then 3 warning beeps, then closes and latches.
However, if I pull the latch manually,(as you would on a non-automatic liftgate) and pass that "1 inch" point, the motor kicks in and raises the liftgate.
Most of the time, it shuts okay, but there have been a few random times where I get the 3 warning beeps (for no reason, there is no obstruction) and it won't shut.

I have the Nissan Quest Model V42 Service Manual...(it's a digital pdf flie) and believe it or not, I cannot find the answer in there.

I've done quite a bit of research, but to no avail....I would truly appreciate any ideas anyone has to offer.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Subaru Master
  • 76,848 Answers

More than likely the lift gate motor has failed.

Posted on Mar 23, 2017

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
MNfisherman
  • 11896 Answers

SOURCE: Latch for hatch of my '07 Subaru is closed with gate open

Unfortunately, you will have to remove the panel of the door, Use flathead screwdriver to pry open. It is very likely the spring fell off.

Posted on May 06, 2009

TwinTurboZ
  • 78 Answers

SOURCE: Automatic liftgate won't open

The lift gate motor needs to be replaced. Preferably at the dealer ship. Its a pain to replace and most shops will do shoddy work and destroy your interior when doing it.

Posted on May 15, 2009

  • 25 Answers

SOURCE: Subaru liftgate lock stuck, liftgate won't close

You should open the tailgate and pull the handle and at the same time push the hook back so that it is not in the way of the lock bar when go to close it. Sounds like it just got jammed and should be able to be fixed with out having to replace. Assuming that it is not rusted and seized.

Posted on Jun 25, 2009

  • 186 Answers

SOURCE: Rusted Subaru Liftgate Latch

Not yet, but if you remove it and take a ladies fingernail file and file between the handle and bracket then use whit lithium greese (plenty) you should be fine for quite a while. Vermonter.

Posted on Aug 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Envoy hatch lock


There is a known TSB for this....
#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Apr 14, 2014 | GMC Envoy XL Cars & Trucks

1 Answer

2008 nissan quest liftgate is inoperable


should be a button in the glovebox somewhere..

Dec 22, 2013 | 2008 Nissan Quest

1 Answer

Where are the relays for liftgate on a 2008 Acadia located


There is a relay and a fuse for the power lfitgate. If you have the owners mmanual, you can find the diagram in section 5-100.

Sep 09, 2012 | 2008 GMC Acadia SLE-1

1 Answer

Rear liftglass won't lock


#07-08-52-003: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE)/Key Fob Transmitter/Door Lock Switch, Lifgtate Hatch or Liftgate Glass May Lock/Unlock When Rear Liftgate Glass Button Depressed - (Sep 13, 2007)


Subject: Rear Liftgate Glass May Not Lock When Using Remote Keyless Entry (RKE), Key Fob Transmitter or Door Lock Switch, And/Or Liftgate Hatch Or Liftgate Glass May Lock Then Unlock When Rear Liftgate Glass Button is Depressed (Reposition Lock Cylinder Wave Washer and Adjust Lock Rod)


Models: 2005-2007 Buick Rainier

2005-2008 Chevrolet TrailBlazer, TrailBlazer EXT, TrailBlazer SS

2005-2008 GMC Envoy, Envoy XL, Envoy Denali

2005-2008 Saab 9-7X




--------------------------------------------------------------------------------
Do This
Don't Do This

Reposition liftgate lock cylinder wave washer and adjust lock rod.
DO NOT replace the liftgate latch or actuator.


Condition
Some customers may comment on one or more of the following conditions:

• The rear liftgate glass may not lock when using the remote keyless entry (RKE), key fob transmitter or door lock switch unless the lock is pressed a second time.

• The rear liftgate or glass locks, but may be unlocked when the rear liftgate lock cylinder button is depressed.

• The rear liftgate locks but the liftgate glass may not lock.

Cause
These conditions may be caused by one or all of the following:

• The rear liftgate cylinder lock rod may be out of adjustment.





• The wave washer on the liftgate lock cylinder may be out of position with the cup side down.

• Excessive movement or slack in the lock rods at the liftgate bell crank assembly.





• The liftgate lock cylinder pawl may contact the rear liftgate glass latch when the lock cylinder button is depressed.

Correction
Important: Do Not remove the rear liftgate lock cylinder from the vehicle to perform this repair.

Reposition the rear liftgate lock cylinder wave washer and adjust the lock rod using the steps below.

Verify the customer's condition.

Open the liftgate.

Remove the upper liftgate garnish molding.

Remove the rear liftgate trim panel.

Remove the cylinder lock rod from the threaded lock rod retaining clip.

Tip
Place the tip of a screwdriver blade into the opening of the C-clip and slowly rotate the screwdriver to pry out the C-clip from the shaft. Then use needle-nose pliers to remove the C-clip.

Remove the C-clip from the rear liftgate lock cylinder push button and remove the wave washer.

Install the wave washer with the cup side up.

Position the wave washer with the curved edges of the wave spring parallel to the tabs on the lock cylinder shaft.

Important: Use needle-nose pliers to slightly squeeze the C-clip back into shape. Make sure the clip seated, you should feel a snap and hear an audible click.

Install the C-clip onto the shaft and in the slot using needle nose pliers. Then rotate the pawl several times to make sure the C-clip does not rotate. If the clip rotates then the clip is not fully seated.

Position the lock cylinder pawl to the full clockwise position.

Pull up on the cylinder lock rod to remove any slack in the bell crank.

Install the cylinder lock rod into the threaded lock rod retaining clip while removing any slack from the lock rod linkage.

Close the lock rod retainer clip.

Close the liftgate assembly.

Open the liftgate glass while keeping the liftgate closed.

Use the key fob to cycle the liftgate to the lock and unlock position while inspecting the rear liftgate pawl. The lock cylinder pawl should have clearance between the latch as shown above. If the pawl is contacting the latch, readjust the cylinder lock rod.

Verify that the customer's condition has been corrected.

Install the rear liftgate trim panel.

Install the upper liftgate garnish molding.

Jan 17, 2012 | 2009 Saab 9-7X

1 Answer

I just bought an equinox 2005 LS and I dont know how to lock the rear door.


To unlock the liftgate, press the unlock button on the Remote Keyless Entry (RKE) transmitter twice or use the power door lock switch.
To lock the liftgate, press the lock button on the RKE transmitter or use the power door lock switch. The liftgate does not have a key lock cylinder.
To open the liftgate, pull up on the handle located in the center of the liftgate.
When closing the liftgate, use the molded handles to pull the liftgate down. Push the liftgate closed until it latches.

Jul 08, 2011 | 2005 Chevrolet Equinox

3 Answers

The rear lift gate on my 2006 Lincoln Navigator will not open automatically or manually and there appears to be no way to access anything inside the door from inside or out.


POWER LIFT-GATE OPERATION - To open the optional power liftgate, push the button on the instrument panel , press on your five-button key fob (if equipped), or press and release the control located in the left rear quarter panel (Figure B). To unlatch the liftgate glass, push the button ) under the center of the license plate lamp shield, or press on your five-button key fob. Do not open the liftgate or the liftgate glass in a garage or other enclosed area with a low ceiling. Keep clear of the liftgate when operating the rear switch. To open the liftgate manually, pull the handle located on the liftgate to release the liftgate from the vehicle. The power system will take over when you release the handle. To close, make certain the rear window is closed, and then pull down the liftgate a few inches to activate power closing. Closing the gate rapidly or more than a few inches may activate the obstacle detection feature and stop the power system.------------ Also click this link for more help:--- http://technoanswers.blogspot.com/2011/05/power-liftgate-on-will-not-open-on.html ------------ This should help.Keep updated.Thanks.Helpmech.

May 19, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

Power liftgate opens on my 2005 quest but then reverses


I would say one or both of the the hydralics (one on each side of the hatch) has gone bad. You can usually find replacements at big auto parts stores or order them (EBAY or other sites) online.

Good luck!

I Can Fix It

Jun 29, 2009 | 2005 Nissan Quest

1 Answer

Liftgate emergency release cannot be found


2/3 of the way down this page with pictures

http://www.wjjeeps.com/liftgate.htm

All WJs feature an emergency unlock/lock switch lever for the liftgate. Should the liftgate become locked and unable to be opened due to a switch or circuit failure, a manual unlock/lock lever is accessible behind a small panel on the interior trim panel. As shown in the photos above, the lever can be moved up or down to unlock or lock the liftgate door.

Jeep Grand Cherokee WJ Liftgate trim and components

May 23, 2009 | 2008 Jeep Cherokee Grand

1 Answer

Automatic liftgate won't open


The lift gate motor needs to be replaced. Preferably at the dealer ship. Its a pain to replace and most shops will do shoddy work and destroy your interior when doing it.

May 11, 2009 | 2005 Nissan Quest

1 Answer

The battery in my 2006 pontiac vibe went dead. I recharged it; however, the setting for the door locks changed. It now unlocks automatically when I turn the car off instead of when I put the car in park. I...


The 2006 Vibe no longer has that feature. It was discontinued after 2005. I have the 2005 so I know how to change it. If your 2006 is able to change then here are the directions from my 2005.
Programmable Automatic
Door Locks
If you have an automatic transaxle, your vehicle is equipped with an auto door lock/unlock feature which enables you to program your power door locks.
Your vehicle left the factory programmed to Mode 4.
The following is a list of the available programming options:
Mode 1: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. There is no automatic door unlocking.
Mode 2: No automatic door locking or unlocking.
Mode 3: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the shift lever is moved to PARK (P) with the ignition on.
Mode 4: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the ignition switch is turned from ON to ACC or to LOCK.
To change the mode you are in, do the following:
1. Set the interior lamp control dial to the door position.
See Interior Lamps Control on page 3-16.
2. Move the shift lever into PARK (P) and close all doors and liftgate.
3. Turn the ignition to ON.
4. Within five seconds after the ignition is turned to ON, press and hold the power door lock switch in
the lock position for about five seconds.
5. The interior lamp will flash to indicate that the mode has been changed. For example, if the lamp flashes once, the function has been changed to Mode 1.
If the battery is disconnected or run down, the mode is changed to the initial mode which is Mode 4.

Jan 22, 2009 | 2006 Pontiac Vibe

Not finding what you are looking for?
2006 Subaru Outback Logo

Related Topics:

319 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...