Question about 1996 Chevrolet Blazer

1 Answer

Motor turns but does not start.

Will crank sometimes if you barely bump the ingnition .

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,959 Answers

If moving the ignition around gets it to crank, you've got a bad ignition switch. A bad switch will occasionally function when moving the key around in the ignition or moving the switch around as you've described. The contacts wear with time (especially if there are a lot of keys on the key chain) and need replacing when constant contact can't be maintained to start the vehicle. Best of luck with your problem. Take care!

Posted on May 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can a car with a broken starter motor be jump started?


If it's the starter motor itself that's knackered it won't start with anything, other than a bump start. Jumping won't knacker the battery though, and if the starter is seized it just won't turn over. Hook it up and give it a go, it won't do any harm. Worst case only give it five or six turns. If it turns over' at all' it's going to be fine.

Apr 04, 2016 | Cars & Trucks

2 Answers

V6 SLE. It cranks but why no spark and won't fire?


I would -start by checking the code from the computer you scjould
get a code from it are you having a problem with the alarm at all
sometime the alarm. Cause problems but even then a code woou
s be my first start there is a thing called am ingniter it a am
Small box for ingnition it hoopla up to the coil see if you getting current to the coil if not that's the 2nd thing to check I think that it please turn the key on so it's hot I think that's it please check and reply

May 30, 2015 | 1999 Toyota Camry Solara

1 Answer

Car shuts off driving


Had this on 91 lesabre, wire going to crank sensor had bare spot and occasionally bumped on eng block above sensor, would die, but started right up again, if going straight, could shift to neutral and restart while coasting. Dangerous when turning corner

Oct 31, 2013 | 1991 Buick Park Avenue

1 Answer

My peugeot 307 1.6 hdi 2005,takes a while firing before it starts,why is this


Try leaving the ingnition on for 30 seconds before cranking the starter, sometimes the timer on the heater warning lamp lies and it is still heating. If this is not it then with a cold motor give it heat twice and open the bonnet and quickly feel the plugs and see if one is cold, either way it could be smart to fit a set of peugeot or bosch fast start heater plugs

Aug 21, 2010 | 2005 Peugeot 405

2 Answers

1999 Mercedes E430. Sometimes it will start,


Changed the crank sensor. Thanks for the help I didn't get.

May 13, 2009 | 1999 Mercedes-Benz E-Class

2 Answers

1999 dodge ram 2500 5.9 cummins diesel.won't start.turns over thats it. put in a new intake fuel pump. still won't start.got fuel to the injectors sometimes.


Check the fuel pressure at the filter. Odds are the lift pump, located below the filter, is toast. Continual cranking of the motor with a bad LP wil cause the injector pump to heat up and burn out. Replace the LP and fuel filter. Bleed the system by cracking the inlet to the injector pump and bumping the enigine over so the LP will run. Once you have fuel at the injector pump, crack injectors 1,3,and 4. Crank the motor for no more 6 or 7 seconds at a time until it turns over. Give the pump time to cool for a couple of mintues between cranks. This process is easier with two people, one to crank and the other to watch for fuel and tighten the injectors once it starts. If the injector pump is fried at this point from cranking with no fuel, the motor should idle, but will stumble all over itself when the throttle is applied.

-Brandon

Jan 11, 2009 | 1999 Dodge Ram 2500 4WD

1 Answer

Fuel problem in 1993 chevy 1500 v6 PU 2wd


you could have a loose wire connection to the fuel pump. try to see if any wire need to be crimped back on the fp!.

Dec 20, 2008 | 2001 Chevrolet Silverado 1500

3 Answers

Ran out of diesel on a 2002 dodge ram 2500 cummins...need to know how to bleed the system


just bump the ignition without starting it let sit for 20 seconds oruntill you hear lift pump shut off then shut off ignition and repeat do it 2 or 3 times should start then cummins is a self priming system has been for years even in semi trucks

Aug 10, 2008 | 2001 Dodge Ram 2500 Truck

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...