Question about 2002 Chevrolet Cavalier Coupe

1 Answer

Drive axle how to get hub off to replace drive axle

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 82 Answers

You will probably have to get it pressed off, I did

Posted on May 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

4wd. How can I replace CV joint?


Hi Terez,here's a repair guide from Autozone site,join their site,it's free,then you can use all their repair guides like me,I will send you 2 links for your CV joint replacement guide,here's the first one. Repair Guides Front Drive Axle Halfshafts AutoZone com Here's the second link. Repair Guides Front Drive Axle Cv joints AutoZone com Here's another link to your locking hubs. Repair Guides Front Drive Axle Locking Hubs AutoZone com

Feb 09, 2016 | 2001 Kia Sportage

1 Answer

Replace Front Wheel Hub Bearing 2002 Jeep Grand Cherokee 2 wheel drive


Removal
  1. Raise and support the vehicle.
  2. Remove the wheel and tire assembly.
  3. Remove the brake caliper, caliper anchor, rotor and ABS wheel speed sensor.
  4. Remove the cotter pin, nut retainer and axle hub nut.
  5. Remove the hub/bearing mounting bolts from the back of the steering knuckle. Remove hub/bearing from the steering knuckle and off the axle shaft.
Installation
  1. Install the hub/bearing to the knuckle.
  2. Install the hub/bearing-to-knuckle bolts and tighten to specification.
  3. Install the hub washer and nut. Tighten the hub nut to specification. Install the nut retainer and a new cotter pin.
  4. Install the brake rotor, caliper anchor, caliper and ABS wheel speed sensor.
  5. Install the wheel and tire assembly.
  6. Remove the support and lower the vehicle.

Apr 22, 2012 | 2002 Jeep Grand Cherokee

1 Answer

I need to know how to take off an axel on a 1992 plymouth laser front wheel drive and a 5 speed


In general, on front wheel drive axle replacement, the method is as follows: raise and support vehicle and remove wheel, remove the axle nut (located in the center of the hub assy.), remove the nut retaining the lower ball joint and separate from the lower control arm, remove axle from wheel hub and suspend the hub to one side, use a pry bar to force the axle out of the trans-axle, reverse process to install and observe all torque specifications.

Feb 08, 2011 | 1992 Plymouth Laser

2 Answers

How easy is it to replace a front wheel bearing assembly? and also a diagram if possible.


It's not too involved. Here's a link with some more information to change it:
http://www.autozone.com/autozone/repairinfo/repairguide/repairGuideContent.jsp?pageId=0900c1528025fae3

Nov 05, 2010 | 1994 Pontiac Grand Am

1 Answer

How to replace 2002 hyundai elantra hub and bearing


With the car on ground, break loose the drive-axle nut, and the wheel nuts , than jack up the car, support it properly, remove the wheel ,remove the axle-nut.
Remove the brake caliper assembly-- support it properly.
Remove the two bolts that hold the hub bracket to the Macpherson strut assemble, remove the lower arm ball joint and remove the steering tie- rod ball-joint attached to the hub bracket. That's it.Slide off the hub /with the bracket off the drive-shaft.
Follow steps backwards to assemble back.

Apr 09, 2010 | Hyundai Motor 2002 Elantra

2 Answers

Replace front left wheel berring on 2002 GMC Yukon


do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

Jan 03, 2010 | 2002 GMC Yukon XL

2 Answers

How do you take off the rotors on a 1990 honda accord


Actually, it’s a bit involved, but you can do it.
Loosen the wheel lug nuts, raise the vehicle and support it securely on jack stands. Remove the wheel and install two lug nuts with 3mm washers under them to hold the disc in place (if the two disc retaining screws are still in place, this will be unnecessary)
Remove the brake caliper. It is not necessary to disconnect the brake hose. After removing the caliper bolts, suspend the caliper out of the way with a piece of wire. Remove the two caliper mounting bracket to steering knuckle bolts.
Remove the drive axle hub nut. To prevent the hub from turning, put a pry bar between two of the wheel studs and against the ground, then loosen the nut.
Remove the cotter pin and loosen the lower ball joint nut about three full turns. Don’t remove it. Separate the lower control arm from the steering knuckle (you’ll need to get or rent a two-jaw puller for that).
Swing the knuckle/hub assembly out away from the car and push the drive axle through the hub assembly until the end of the drive axle is free of the hub. The shaft on the end of the drive axle is often hard to dislodge from the hub, so you may have to tap the outer end of the shaft with a soft mallet until it pulls easily out of the hub.
After the hub and axle are separated, support the outer end of the drive axle with a piece of wire to avoid unnecessary stain on the CV joint.
Remove the four bolts that hold the hub and brake disc assembly to the steering knuckle and remove the hub and disc.
Put a pry bar or something like one between two of the wheel studs to keep the whole thing from turning as you maybe put your feet against the bar, and then remove the four bolts that hold the disc to the hub assembly. Then you will have your disc. Installation is the reverse.
I hope this helps you. Give yourself plenty to time to deal with it.

Dec 01, 2009 | 1990 Honda Accord

1 Answer

CV drive axle won't seat into hub flange


no special tool required the shaft must be completely straight and the splines lined up for it to go in

Sep 30, 2009 | 2002 BMW 5 Series

1 Answer

Rear drive axle hub removal on a 1994 318i


Need to be pressed off Take whole assembly off and press hub out of bearing Crack retaining ring behind bearing with a cold chisel Press hub back on to new bearing

Jul 09, 2009 | 1996 BMW 318

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...