Question about 2005 Chrysler Town & Country

Open Question

Torx bit size?!?

Need to know what size torx bit is needed for rear brakes on a 2005 Town and country van. Any help out there?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 11 Answers

SOURCE: What size torx socket do I need to take caliper off?

most likely a t50

Posted on Feb 10, 2009

Ad
  • 114 Answers

SOURCE: we need to install a new rear heater hose on our van and are not sure how too do it

I've done this many times
You will need a tubing cutter
Screwdriver
I think a 7 or 8mm socket
hose clamps
the appropriate amount of heater hose
zip ties

cut the steel heater line at the front in a place you can get access to,leave yourself enough steel hose on the rear to allow you to put the heater hose on cut off the steel hose and discard, and use 2 hose clamps on either end do the same for the other heater hose,this way is cheap and easy and permanant.Be sure that when you run the heater hose keep it away from hot or moving parts,use the zip ties to fasten it along the way,this should take about a half hour or so depending on your skills and working conditions,remember to buy some antifreeze to top up the system because you are going to spill some,remember to clean any spills animals love it and it is deadly.

Posted on Apr 16, 2009

hunterd777
  • 14 Answers

SOURCE: Early wear on front brakes /rotors for 2008 Town and Country

I work for a brake repair shop and trust me you are not alone.Enterprise and alot of other people bought the same van and had the same trouble.I hate to say but it doesnt stop there.About every 14 to 15 thousand miles you have to replace the front pads.As of now they dont have an upgrade,for instance ceramic pads, but I am sure they will very soon

Posted on May 01, 2009

  • 139 Answers

SOURCE: what tools will i need to replace my brake pads on

should be like a 3/8 allen wrench but if it is a torx should be a t45-t50

Posted on Aug 01, 2009

  • 285 Answers

SOURCE: what size torx bit do i need to remove the screw

if its the front you want to change,its a t60 torx,hope this helps

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What size Allen wrench do I need for a Chevy van g20 1991, to change my brakes?


I think they were a 3/8 allen. I also found that a torx bit T50 I think works also. GM changed the sizes around on some that had heavy duty brakes.

May 31, 2015 | Chevrolet G20 Cars & Trucks

1 Answer

HOW DO YOU GET TO THE REAR SPARK PLUGS ON A 98 TOWN AND COUNTY VAN?


well you can reach around the top of the engine to get to the rear plugs or go underneath and get at them from the bottom. you can remove the wiper cowling to gain access more room as well.

Sep 09, 2014 | 1998 Chrysler Town & Country

1 Answer

Am tryng to change the front brake pads from a 2003 town and country limited, but i need to know wich size of hex wrench do i need


Metric Size --- 10,12 what ever it takes

All vehicles from 1980 on ,use mostly Metric
Wrenches,Sockets & Torx drivers

Jul 19, 2011 | Chrysler Town and Country Cars & Trucks

2 Answers

Chrysler Town & Country Minivan Rear Drum Brakes


I replaced the brake pads on a '94 Chrysler town and country, I had the rotors turned also, I did not use any anti-vibration substance on the shoes. I hear a clicking noise from front brakes.

Apr 16, 2010 | 2005 Chrysler Town & Country

2 Answers

What type of wrench is needed to remove front disc brake caliper? It has a rubber boot over it. A 1/4 hex is too small and a 5/16" too big.


if its a hex may be 7MM. does it look like a star? its a TORX. you will need a set, pretty cheap at the parts store.

Oct 08, 2009 | 2005 Chrysler Town & Country

3 Answers

What tool do I need to remove the caliper guide pin bolt on a 2004 town and country?


I just finished doing the rears on my 2005 T&C. The caliper pins need to be removed with a 7mm allen wrench. I used an allen socket for a 3/8" ratchet, which was much easier than using my wrenches. These pins are threaded and cannot be "tapped" out as said by someone else.

When you replace them, make sure you have some high temp grease to put on them and check the pin rubber boots to make sure that they are not cracked or damaged. Good luck!.

Jul 31, 2009 | 2005 Chrysler Town & Country

2 Answers

Rear Brake caliper what are the size of the Guide Pins?


for the most part its a 10-MM and try these website to see if they have any information for you www.autozone.com and www.alldatadiy.com if all fails stop by your local library and get your hands on a haynes auto repair manual for your van.

Jun 21, 2009 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...