Question about 2004 Jeep Liberty

Open Question

2004 Jeep Liberty will not start

Shut vehicle off and went into store came out and vehicle would not start. Will not crank with key in ignition. Everything electrical works. When you turn the key it doesn't make any noise at all. Checked the fuse block under the hood all fuses have power except ignition and fuel. Have checked all fuses and relays and to the best of our knowledge they are all good. Does anyone have any suggestions?

Posted by on

  • lakrawz May 20, 2009

    Yes we tried both sets of keys. Power is reaching starter. There is no power at the fuse block under the hood for ignition and fuel. We have been told it is a bad ignition switch and that there is no power leaving the switch.

  • Robert Debison May 11, 2010

    is power reaching starter?could be a bad connection at starter..did you try another ignition key?these vehicles have a sentry key immobilizer(theft system)make sure all connections at starter clean and secure

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 17 Answers

SOURCE: cranks but no start

check the fuses inside on the right hand front kick panel

Posted on Aug 20, 2008

fastboyz
  • 674 Answers

SOURCE: my 2002 jeep liberty failed the illinois Emission test !

there are many items that will cause your truck not to be clean
when you spark get weak it will not burn all the fuel and not set a code so a good ign tune up pluga and plug wires and related parts and a good injector cleaner. then you need to take it out for a long drive to clean out the system. i have seen many cars not pass just because of alot of idle time.
you didnt say how many miles are on this jeep or how long since a tune up?
later paul

Posted on Nov 01, 2008

  • 10 Answers

SOURCE: 2007 Jeep Wrangler Unlimited Crank-No Start. Replaced FP.

Hey Tim take a look at this, will this help ?
SUBJECT:
No Engine Crank Or No Engine Start Due To Electronic Lockup Of The WCM / SKREEM
OVERVIEW:
This bulletin involves the replacement of the Wireless Control Module (WCM), and if
equipped, the replacement of the Electric Steering Column Lock (ELV). The WCM is also
referred to as the Sentry Key Remote Entry Module (SKREEM).
MODELS:
2007
SYMPTOM/CONDITION:
The customer will experience a no engine crank AND a no engine start condition. Also, the
remote keyless entry (RKE) system will not operate. This condition may be due to an
electrostatic discharge (ESD) from the ignition key into the Wireless Control Module
(WCM), causing the WCM to electronically lockup. This condition may occur more
frequently in dry and/or cold weather conditions where a sufficient electrostatic charge is
more easily produced. This condition is corrected by the replacement of the WCM
DIAGNOSIS:
1. With the condition present (i.e. the vehicle in the no crank / no start condition), connect
the StarSCAN® scan tool to the vehicle.
2. Turn the ignition switch to the “ON” position, and power up the StarSCAN®.
3. If the WCM is electronically locked up, the StarSCAN® will display the WCM as being
“off bus”.
4. If the no crank / no start condition is present, and the WCM is “off bus”, then reset the
WCM by temporarily removing the IOD fuse (with the key out of the ignition switch),
wait for 10 seconds and then reinstall the IOD fuse.
5. With the IOD fuse reset having been performed, verify that the vehicle will now crank,
start, and run.
6. If the condition is temporarily corrected by performing the above steps, and if the part
number of the WCM is earlier than the part number of the WCM listed in the part
reference table in the Service Bulletin Parts Required Section below, then perform the
Repair Procedure.

Posted on Jun 24, 2009

blueextc3221
  • 15935 Answers

SOURCE: engine will not turnover

If there is no power coming IN to the starter relay - the ignition module has failed.
Replace the Ignition.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

Posted on Sep 24, 2009

wracefans24
  • 1985 Answers

SOURCE: 2004 jeep liberty does not produce heat when

check and fill radiator and filler canister for coolant.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Jeep Liberty- Why won't it roll (if pushed ) in Neutral? Won't start, but dash lights & security works !?


wow cathy 4 post now.
get it jump started, does it start now?
charge the battery to 12.6vdc rested
does it crank now, you mean it wont crank or
cranks robustly but will not start
or cranks and runs for 3 seconds.
is the IMMO light off, it has its own lamp, mine is sold read, no words, no icons, just red. if on, it WILL NEVER RUN.

key on
cranks does it crank.???
if not jumper start it. if IMMO is off.

Aug 28, 2014 | 2006 Jeep Liberty

1 Answer

2004 jeep liberty won't turn over nor crank


The anti-theft system won't allow it to start . You replaced parts without knowing what would happen . The key has a transponder is the head of the key . The module that controls anti-theft doesn't see the transponder code an locked up the vehicle . Your best bet ,have it towed to a qualified repair shop . You don't have the tools or knowledge to fix it .

Jul 04, 2017 | 2004 Jeep Liberty

1 Answer

2004 jeep liberty 3.7 auto no crank no back up lights


you may have a problem with your neutral switch.if the switch is bad your vehicle will not start and also you will not have reverse lights.

Sep 07, 2011 | 2004 Jeep Liberty

1 Answer

My 2004 jeep liberty stopped running two fridays ago. my mother was driving it, went into her insurance place and left my 13 y/o son in the car with the car running and a/c on. about 8 minutes into that...


I would get the battery checked, even new ones can be bad, I had a Bosch that went bad after 5 months.
Get the codes read, my 2003 Liberty recently had a problem starting also, thought it was the fuel pump or filter, code came back as the Crankshaft position sensor being faulty, could be a sensor giving you trouble, mine would start right away once it got warm.
When it comes to sensors there is not a lot of difference between making the circuit complete and not.

Hope this helps!
Cheers

Jun 14, 2011 | 2004 Jeep Liberty

1 Answer

I have an 08 Jeep Liberty that has a remote starter on the key. I tried to unlock the car with the remote, however, that didn't work, so I unlocked the car with the key. The alarm went off, I tried pushing...


Sounds like you have a key without the chip in it. Replacement keys without the chip will only unlock the doors and will activate the theft alarm when you start the vehicle.

May 22, 2017 | 2008 Jeep Liberty

1 Answer

2004 jeep liberty 3.7 eng will not crank over jump start it will start battery only year old


Sounds like your altenator is bad. Most part stores will test for free, in or out of vehicle. Battery, Alt, and starter can be checked for free.

Oct 16, 2009 | 2004 Jeep Liberty

2 Answers

Tried to start jeep liberty 2005 went and opened


Aside from the part about the remote, I would first check to make sure the battery has a solid 12volts in it and that the terminal connections are clean. After this, then check to see if operation has been restored. Jumping across a battery with bad connection often prevents the vehicle from starting. Also try closing the doors and then locking and unlocking drivers door with the key itself. This should re-set the security system

Apr 15, 2009 | 2005 Jeep Liberty

1 Answer

2004 liberty


If your engine light came on, the engine module could have stored a code.
You need to have a scanner to check what code it is and that will point you toward the solution.
Possible causes could be (crank sensor, tps sensor or oxygen sensor).
Don't go replacing parts until you scan the vehicle for codes first.

Oct 03, 2008 | 2003 Jeep Liberty

3 Answers

2002 Jeep Liberty Prolonged Cranking problem


it sounds like your timing system is on its way out the belt probably has streched and is close to not working at all.when u turn your ignition and applies power to the starter for the vehicle to start the piston must be in the right position when the electrical current ignites the spark plug. if u smelled gas thats from fuel that didn't explode in the chamber from a misfire, the misfire is because the spark and the chamber position are not in sync

Jul 13, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2004 Jeep Liberty Logo

Related Topics:

1,059 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...