Question about Mitsubishi Lancer

1 Answer

Changing rear wheel bearing on a 1991 CB Lancer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 209 Answers

You have to take off the wheel then also the breakes theres a bolt on the center of it take that off then you can pull the bearing off...

Posted on May 11, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 315 Answers

SOURCE: noisy wheel bearings

Yea man, take it to the shop.

Posted on Mar 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a front wheel bearing?


front wheel bearing is pressed into hub and has retaining clip on rear and then cv axle shaft comes through center and has a nut and keeper pin. Rule of thumb is to replace both front wheel bearings at same time. raise front of vehicle place on jackstands for safety remove front wheels remove brake calipers remove front rotors and cv axles remove steering hub assy from lower ball joint,tie rod end and struts take hub to shop and have bearing pressed out have new bearings pressed in reassemble front wheels in reverse order of disassembly.

Aug 03, 2014 | 2002 Mitsubishi Lancer

1 Answer

Lancer vibrates at 90 to 100 ks at front at front left


bent rim, tires out of balance, worn cv axle, bad wheel bearing, warped brake rotor, bad tire. Change that wheel to the rear, and see if the vibration moves with the wheel. Depending on the vibration, could be a motor/transmisson mount.

Dec 17, 2013 | 2002 Mitsubishi Lancer

4 Answers

The right rear wheel of my 1991 Justy 4wd sways and made noise on the road. What would be the problem thanks


the rear Hub bearing is out!! need to jack it up take the wheel off and the caliper and disk and replace the bearing if it has drum brakes which is should!! you will have to pull the axle to get to the bearing

Jan 17, 2010 | 1991 Subaru Justy

2 Answers

The rear wheel bearings on my k reg mitsubishi lancer was replaced by a garage 3 weeks ago but it has just disintergrated on the motorway, any idea what the garage may have done wrong ,i know they did not...


Hi:
Your guess is probably correct that they were over tightened on installation, or perhaps not greased at all? even if they were loose, they wouldn't be destroyed.

Nov 20, 2009 | 2002 Mitsubishi Lancer

1 Answer

How do you change the rear wheel bearings


The rear hub and bearing are combined into a single assembly. The bearing is sealed for life and requires no lubrication or attention. If the bearing is worn or damaged, you have to replace the entire hub and bearing assembly:
loosen the rear wheel lug nuts, raise the vehicle, place it on jack stands and remove the rear wheel.
Remove the brake drum or caliper and disc.
Remove the dust cover (in the center).
Unstake the hub retaining nut (bend the part out that locks it), unscrew the nut and remove the thrust washer then remove the hub assembly.
Install the new assembly and thrust washer, tighten the new nut to torque 134 lbs, then stake in the edge of the nut (opposite of unstaking).
Tap the dust cover into place, all around the edge until it's seated.
Reverse removal for the rest.
Hope this helps you understand the process.

Nov 19, 2009 | 1991 Honda Accord

1 Answer

1991 mr2 rev 2. car sways left to right at 80 mph


Clunking? Probably one or both wheel bearings. Dude, that car is like UNSAFE to drive!! Jack the rear of the car up and yank on the wheel. If it moves the bearings are bad. Pull in and out and also pry up and down with a bar. Check for broken or bent rear suspension parts, or just plain worn out bushings.

Jun 30, 2009 | 1991 Toyota MR2

1 Answer

Noisy wheel bearings


Yea man, take it to the shop.

Mar 17, 2009 | Mitsubishi Lancer Cars & Trucks

1 Answer

02 Lancer ES help with diagnosing left side of Engine Vibration noise.


sounds more like a wheel bearing,jack the car up and support with axle stands,then grab the front left wheel at both sides and shake it hard.then grab it at the top and bottom and shake it hard.if a knocking can be felt through the wheel then its most likely a wheel bearing.repeat the test for the rear wheel.also with the vehicle jacked up,spin the wheel and put your ear next to it,if it makes a dry whirring or grinding sound as it spins,this is a symptom of a worn wheel bearing

Oct 11, 2008 | 2002 Mitsubishi Lancer

3 Answers

Replacing front wheel bearing


those are sealed units and are intergrated with the wheel rotor if the bearings are bad they must be replaced and those are dealer only items. labor for each side is about 1 hour for remove and install per side. unfortunately there are no aftermarket parts available just yet. hope this helps

Aug 28, 2008 | 2003 Mitsubishi Lancer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

495 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...