Question about 1999 Lexus LS 400

1 Answer

Low winshield washer light is on i have refilled reservoir how do you reset light

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 122 Answers

Should have reset itself when you filled it,possiblly the sensor is bad, and or corroded up, window solovent is pretty ruff stuff when its alloewed time too dry up,

Posted on May 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset low brake fluid light and brake light on chevy impala 2005


The fluid light should go out when you refill the reservoir. You may have tot remove the brake light switch from the brake m/cyl to allow the switch to reset.

Mar 27, 2013 | 2005 Chevrolet Impala

1 Answer

Frozen winshield washer lines


Find a heated garage, you need to thaw out he lines, or use a hair dryer if you can follow the line path. When working, drain all the fluid by holding down the spray button on the car. Go and buy he heavy duty washer fluid with the lowest freezing point you can buy and refill your washer reservoir with it. Don't add any water Most likely you had water in the reservoir and it froze.

Jan 20, 2013 | 1998 Ford Taurus

1 Answer

2011 Toyota Camry winshield washer fluid light on dashboard won't turn off after filling tank.


The sensor inside the tank is defective or covered in goo. Remove the sensor from the tank or remove the tank and flush it clean with hot water and a mild solution of white vinegar, if the sensor still reads the tank is low replace it.

Sep 25, 2012 | 2011 Toyota Camry

2 Answers

Turn on my wipers try to spray wwasher on winshield nothing happens ....what could be wrong?


A few possiblities. Lets start with the cheapest first. Washer fluid, could be low, I'd check it first. When you press the spray button you should be able to hear the pump turn on (usually ON the washer reservoir). If it turns on you probably have a leak or blocked line. If you don't hear it cut on I'd check your fuses and then check to see if it's getting power to the plug with a multi-meter or test light. If it's getting power and not cutting on then it's probably the washer pump. Hope this helps.

Jan 17, 2012 | 1995 Cadillac DeVille

1 Answer

Which fluid do I top up with in the reservoir next to the converter under the bonnet? Toyota prius 2005.


Is a old school habit to top up fluids, if is low is , then there is a leak, or somebody serviced wrong, the reservoir that you are mentioned is call inverter reservoir, it uses long life toyota coolant, if the water pump leaks it is the one that will get low.

for the record, the only fluid that you refill is the windshield washer fluid.

Jan 20, 2011 | Toyota Prius Cars & Trucks

1 Answer

Winshield Washer Fluid extremely low pressure


The washer pump is located in the right front fender, mounted infront of the wheel. Remove the front portion of the wheel well splash cover to gain excess. This pump does the work for the front and rear washers. Verify that the pump is working and then check for a pinched hose.
However, if you hear the pump working,as you say, open the hood and take the hoses off the squirter nozzles to see if there is good flow of fluid. If there is, then your nozzles are plugged. You may be able to clean them out with some air pressure. Careful working with the nozzles, as they are plastic and break easy.

Steve

Jan 11, 2010 | 2004 Hyundai Santa Fe

1 Answer

Washer pump for winshield doesn't work


This should just push into a grommet in the washer fluid reservoir. I hope this helps!

Jan 30, 2009 | 1991 GMC S-15 Jimmy

2 Answers

Winshield washer fluid


Sometimes they have a port in the back along the inside behind an access panel. Others have a seperate washer fluid tank in the motor compartment. See if there is an access panel behind the rear seat on either side.

Dec 10, 2008 | 2000 Dodge Caravan

2 Answers

Replacing windshield washer pump


I assume you access from underneath. Remove plastic shroud and expose reservoir and pump? right?

Nov 11, 2008 | 2001 Hyundai Elantra

1 Answer

Winshield washer motor does not run


These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, inner+fender+w+text.jpgyou know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually 2384f71.jpglocated inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.

Jun 08, 2008 | 2001 Honda Civic

Not finding what you are looking for?
1999 Lexus LS 400 Logo

Related Topics:

232 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

907 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...