Question about Hyundai Elantra

1 Answer

Need to installation instructions on cargo net for 2008 elantra

2008 elantra installation instructions for cargo net

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Read your Owner's Manual... best solution

Posted on May 31, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a cargo net on Hyundai Sonata?


One would hope that the dealership would have installed it for you. Beautiful car by the way. They done everything nicely in these cars.

In the instruction manual that comes with the cargo net (Dealer accessory) it will show you how to remove 2 anchor bolts on the left and ride side of the trunk. The carge net should come with the replacement anchor hooks to allow you to hook the elastic straps to both sides to get maximum use of the net.

I would say since your car is as new as it is. Come into the dealer and get them to put it in for you.

Dec 25, 2014 | 2015 Hyundai Sonata

1 Answer

What do I need to unscrew in the trunk to change the reverse light in my 01 chevy impala


Tail Lamp Assembly Removal & Installation To Remove:
  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.
  8. Remove the side marker lamp socket by turning counterclockwise.
To Install:
  1. Install the side marker lamp socket by turning clockwise.
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
prev.gif next.gif

Oct 18, 2010 | 2001 Chevrolet Impala

1 Answer

Check engine light on and heat gauge all the way to the left at 100


Need to check with OBD. Over heating means fan is not working or if newly installed engine, the mechabis did not installed the engine properly.

Oct 07, 2010 | 2008 Chevrolet Express Cargo

1 Answer

I NEED DIRECTIONS ON HOW TO CHANGE THE LIGHT


You need to replace the turn signal and brake light bulb, any auto part store will carry it $2 per bulb. In trunk remove carpet covering where the cargo net would hook.Unscrew this, then you'll see the wires just move them and unscrew the bulb, and replace with new one.

Mar 07, 2010 | 2008 Pontiac G5

1 Answer

2008 Xterra and the cargo net was shut in door


push rear hatch to closed position to release locking mechanism

Sep 20, 2009 | 1997 Chevrolet Blazer

1 Answer

Changing factory installed foglight bulbs on 2008 elntra


Your 2008 Elantra fog lamps are probably still under warranty. Take the vehicle into a Hyundai Service Center (dealership) or call the nearest one. Give them your vehicle VIN and ask them if the fog lamps are still under warranty. If they are, they will replace them for FREE!

Jun 20, 2009 | 2008 Hyundai Elantra

2 Answers

Left rear turn signal bulb is burned out.


Tail Lamp Assembly
Removal & Installation
To Remove:

  1. Open the rear compartment.
  2. If equipped, disconnect the cargo net.
  3. Remove the wingnut and pull back the rear compartment trim panel.
  4. Remove the wingnuts from the tail lamp assembly.
  5. Remove the tail lamp assembly from the rear body panel.
  6. Disconnect the electrical connector from the tail lamp assembly.
  7. Remove the tail lamp socket by turning counterclockwise.

  1. To Install:
  2. Install the tail lamp socket by turning clockwise.
  3. Connect the electrical connector to the tail lamp assembly.
  4. Position the tail lamp assembly to the rear body panel.
  5. Install and secure the wingnuts that attach the tail lamp assembly to the body panel.
  6. Position the rear trim panel to the rear compartment. Install and secure the wingnut.
  7. If equipped, connect the cargo net.
  8. Close the rear compartment.
      Please don't forget to rate !!!!!!

    Mar 28, 2009 | 2002 Buick Century

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    401 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    75797 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22114 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8152 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...