Question about 1994 Toyota Camry

3 Answers

94 Camry brades won't bleed

Bench bled the new and replaced the old leaking master cylinder this weekend. Bled RR first, then went to LR next and got nothing, hardly a few drops. Went to the RF and got the same results as LR, no fluid, no air, no anything. Moved to LF which bled fine. Repeated this process 4-5 times with no change. The RR and LF bleed normally but can't get a thing out of LR or RF. I'm 56 yrs old and been under cars all my life but this one has got me stumped. This car is an automatic with the 2.2 4cyl w/o abs.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Theres is a other way to bleed brakes.
1: get a gar with a lid
2: punch a hole in it the same size of a brake line
3:insert the brake line in the hole put in almost to the bottom leave some space put the brake fluid in the gar put the top on.
4: use duck tape and tape the line to the gar so no air gets in.
5: get a rubber hose that fits a little bit over the brake line.
6: loosen the bleeder a little bit a little put the rubber hose on the bleeder.
7: push your brakes andwatch the air come out and **** the brake fluid in then tighten the bleeder go on to your next tire. watch your fluid make sure its full and the cap on.

this work on my friends van and i bleeded my clutch too hope this helps.

Posted on Jul 12, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

Try pumping the brakes a few dozen times to push air down the lines a ways then open all the bleeders and walk away for a while and let the mystery of the car do the work for you,then of course add fluid, tighten the bleeders and try them.if that doesnt work then maybe the proportion valve is bad.if this doesnt work then im right beside you on this-stumped

Posted on May 10, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 98 Answers

Try starting the car then bleed them

Posted on May 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Spongy braks


When you do that, you must bleed the whole system in a sequence order. You start with the brake line that is the longest and bleed that and then move to the next and so on. So you should have bled RR, LR RF and LF brake lines in that order.

Dec 04, 2014 | Cars & Trucks

1 Answer

No brake pedal. pads good, fluid up in master. pedal won,t come up when bled?


fluid is by passing rubbers in master cylinder . replace unit. noise if you are running engine could be air leaking from faulty booster unit

Feb 01, 2013 | Cars & Trucks

1 Answer

No pressure on brake pedal 95 suburban 2500 4x4 7.4L


try bleeding your ABS block first, if that doesn not work could need a master or proportioning vavle. Some scan tools are capable of bleeding the ABS system on some vehicles, and some you have to bleed manually.

Apr 07, 2012 | 1995 Chevrolet Suburban

1 Answer

Installed new master cly.,bench bled, bled rr, broke off lr bleed valve (not opened), bled rf, tried bleeding lf but getting no fluid to caliper. is problem with proportiner valve?


The problem is probably that you must do the lr before moving to the front. The air in the lr will make it too spongy to bleed the front.
A wheel cylinder is only $25, so you might as well just replace it. And if you use vasoline or brake lube on the bleeder, it will not rust up on you next time.

Proportioning valves are not supposed to block a bleed. They can malfunction, but should not supposed to. And if you have the back working, that should reset the proportioning valve anyway. You can't leave the back. It must be finished.

Jun 07, 2010 | 1990 Plymouth Voyager

3 Answers

No brake pressure


should not need to bleed module try giving the proportion valve afew good smacks sometimes this will dislodge the valve then rebleed

Jun 03, 2009 | 1998 GMC Jimmy

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

2 Answers

2005 f150 spongy brakes


possibly new master cylinder is defective

Mar 24, 2009 | 2005 Ford F-150

2 Answers

1989 Ford F350 2 wheel drive dually 460 ci gas motor


5 Inspect Brake Fluid Type Brake fluid loss or contamination grey_line.gif 10 Inspect Master Cylinder (Brake System) Worn or leaking brake master cylinder. grey_line.gif 11 Inspect Brake Power Booster Damaged booster vacuum line/check valve, or diaphram

Nov 24, 2008 | 1989 Ford F 350

2 Answers

Brakes


HAS THE LARGE VACUUM LINE TO THE MASTER CYLINDER COLLAPSED, I.E. FLATTENED?

Aug 11, 2008 | 1984 Volvo 240 Series

Not finding what you are looking for?
1994 Toyota Camry Logo

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...