Question about 2002 Honda Accord

Open Question

Rear wheel bearing nut torque setting

Honda accord 1.8 sport 2002 rear wheel bearing nut torque setting

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

  • 583 Answers

SOURCE: need torque setting for 1993 geo tracker front

i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"

Posted on Nov 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque requirement for rear wheel bearing


Axle nut should be torqued to 139lb-ft.

Aug 12, 2012 | 1999 Honda Accord

1 Answer

Need to know the torque setting for the rear weel bearing on my 2001 ford focus. it takes a 30mm socket.


The torque setting 49 ft. lbs.


Torque Specifications
Description Nm lb-ft lb-in Wheel nuts - steel/alloy wheels 128 94 - Wheel spindle retaining nuts 66 49 - Wheel cylinder retaining bolts 12 9 - Rear brake pipe to wheel cylinder union 8 - 71 Rear wheel speed sensor retaining bolt 9 - 80 e0001241.jpg
Item Part Number Description 1 - Tie bar and knuckle 2 - Backing plate 3 - Wheel spindle 4 - Sensor ring - anti-lock control 5 - Grease cap 6 - Wheel bearing retainer 7 - Drum

Apr 26, 2011 | Ford Focus Cars & Trucks

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

It looks like something behind my rear wheel is broken; the part the brake pad is attached to; either that part or behind that part something is broken causing the wheel to wabble like its about to fall...


Sounds like a wheel bearing. If you jack up that side of the car and the wheel flops around than the bearing is bad. It is not uncommon for these vehicles. They usually start to make a lot of noise before they get that sloppy.

The bearing is a bolt in style and as long as you have a basic set of tools, a socket to fit the axle nut, and a 1/2" torque wrench to torque the axle nut on the new bearing, it is a pretty easy job to do.

Dec 07, 2010 | 2002 Pontiac Aztek

1 Answer

Does anyone know the torque wrench settings for the rear hub/wheel bearing nuts on a 2002 Peugeot 206 1100cc please? Also the road wheel bolts?


Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Jan 23, 2010 | 2005 Peugeot 405

1 Answer

How do you change the rear wheel bearings


The rear hub and bearing are combined into a single assembly. The bearing is sealed for life and requires no lubrication or attention. If the bearing is worn or damaged, you have to replace the entire hub and bearing assembly:
loosen the rear wheel lug nuts, raise the vehicle, place it on jack stands and remove the rear wheel.
Remove the brake drum or caliper and disc.
Remove the dust cover (in the center).
Unstake the hub retaining nut (bend the part out that locks it), unscrew the nut and remove the thrust washer then remove the hub assembly.
Install the new assembly and thrust washer, tighten the new nut to torque 134 lbs, then stake in the edge of the nut (opposite of unstaking).
Tap the dust cover into place, all around the edge until it's seated.
Reverse removal for the rest.
Hope this helps you understand the process.

Nov 19, 2009 | 1991 Honda Accord

1 Answer

How tight should i make the axle nut after fitting new rear wheel bearing assembly if i don't have a torque wrench


tighten the nut down and spin the hub to set the bearings and then back it of a 1/4 turn

Oct 17, 2009 | 1994 Honda Civic

2 Answers

What is the torque specs for the front wheel bearing/hub assembly nut on a 2002 ford mustang?


Wheel bearing don't have torque specs (to the best of my knowedge). They have a procedure - in this case it is....
1. With everything clean and packed with grease, snug the bearing lock nut until it stops.
2. Reverse it about 1/8th to 1/4 turn and insert the cotter pin.
Done

Oct 11, 2009 | 2002 Ford Mustang

1 Answer

Torque specs needed


on a 1999 Honda Accord, the torque for the front axle nut is 181 ft lbs. For the most part, sung it up and then go a bit further. If you are reusing the old axle nut, tighten it until the stake mark on the nut lines up with the notch in the axle (make sure to re-stake it). check out alldata.com/diy for individual vehicle subscriptions which have all the repair info you will ever need. If you had the steering knuckle out, tighten the balljoint nuts on the upper and lower control arms until they are tight and then tighten until the hole lines up to recieve the cotter pin.

Mar 18, 2009 | 1997 Honda Accord

1 Answer

VW Jetta torque setting and hub nut size????


129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Mar 13, 2009 | 2002 Volkswagen Jetta TDI

Not finding what you are looking for?
2002 Honda Accord Logo

Related Topics:

511 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...