Question about 1995 Mercedes-Benz S-Class

2 Answers

Changed brake pads! Success.. Now I need to bleed the brakes.

Changed front brake pads. Now I need to bleed the brakes. The brakes are not firm. I read to use a brake nipple to bleed. What and where the heck is that? Does this require taking for the tires off again to get to the caliber?

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

To bleed you brake system, you will need brake fluid, a jar, and a couple feet of small hose that fits tightly on the bleeder screws. You should not need to remove the tires to access the bleeder screws, but you may need to raise the vehicle a bit to access them.

To bleed the system, start with the right rear wheel. Put a couple inches of brake fluid in the jar, attach the hose to the bleeder screw, put the hose in the jar of brake fluid, then open the bleeder screw. Once the bleeder screw is open, pump the brake several times. Next, close the bleeder screw. After you close the bleeder screw, remove the hose and jar, then fill the master cylinder with brake fluid.
Repeat the steps going to the left rear second, right front third, and left front last.

Once you have bled the system your brakes should be tight and working nice.

I hope this information helps you, and I wish you luck on your repair.

Posted on May 10, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 41 Answers

START UP TOP WITH MASTER CYLINDER BEFORE YOU GO TO CALIPERS,IF YOU HAVE A BLEEDER START WITH MASTER CYLINDER FIRST.

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replaced all 4 brake pads bleeding them now and not getting g a firm pedal


Why do you need to bleed the brakes for changing pads?

Mar 24, 2016 | Cars & Trucks

1 Answer

Brake pedal soft after changing pads and bleeding brakes


You will need to bleed the brake system. I would start with the rear brakes lines and work towards the front.You must have key off engine off when bleeding brakes, apply pressure on brake pedal 10 times and hold. The brake line is now ready to be open. Open and let the stream of fluid come out and close the line tight. Then release brake pedal once bleeder screw is close. This procedure must be repeated twice front and back. After, brakes have been bleed pump the brake pedal before putting in drive.
Note: Don't let the resevoir run low on brake fluid. This will cause air bubbles to accumulate on the brake system. Always top off before opening bleeder screw.

Nov 21, 2011 | 1992 Chevrolet Corsica

1 Answer

Changed both front (rears are drums and did not change) brake calibers and pads on my 1998 F150 pickup 2 wheel drive. In doing so I let the master cylinder go empty. How do I bleed the brakes now. I have...


your probably going to have to bleed the entire system.1st try & bleed the master cyl.
basicly the same as you would bleed the front/rear brakes. pump pedal & hold while someone
loosen the brake line on the master cyl. after m/c is bleed move to r/r,l/r,r/f,l/f wheels in
that order. if you have abs brakes & you got air in the pump a scan tool may be needed
to bleed properly.

Jul 17, 2011 | Ford F-150 Cars & Trucks

1 Answer

I have a 2001 BMW 318I, E46 MODEL , HOW DO YOU FIT BRAKE PADS TO FRONT AND REAR, THANKS TREVOR.


YOU NEED A PISTON COMPRESS TOOL TO PRESS PISTON BACK IN THE BORE WITH THE BLEEDER SCREW OPEN ON THE CALIPER*.CLOSE BLEEDER SCREW JUST BEFORE THE CALIPER PISTON IS PUSHED FULLY INTO CALIPER.THIS WILL ALLOW ROOM FOR NEW BRAKE PADS AND CALIPER FIT OVER THE BRAKE ROTOR.WHEN FINISH.PUTTING BRAKE PADS ON YOU HAVE TO BLEED BRAKE SYSTEM.DONT DRIVE VECHICLE IF YOU CANT GET A GOOD FIRM BRAKES.

Oct 15, 2010 | BMW 318 Cars & Trucks

2 Answers

After changing pads and roto's on the front the brake petal goes to the floor and won't recover pressure? I didn't loosen brake lines or bleeders


You obviously got air in your lines while you were changing the pads. The brakes now need bleeding. Once you bleed them, your pedal will come firm again. But the good news is that you will only have to bleed the front brakes....Please don't forget to rate this answer for me...

Feb 22, 2010 | 2002 Ford SVT Focus

1 Answer

Need help bleeding the front calipers


THERE IS A BLEEDER NUT ON EACH CALIPER,ONE PERSON BLEEDS AND THE OTHER PUMPS THE BRAKE PEDAL

Oct 27, 2009 | 2007 Chevrolet Malibu SS Sedan New Cars

2 Answers

How do I bleed the front brakes on a 2004 audi a4 quattro?


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Oct 01, 2009 | 2004 Audi A4

2 Answers

1999 Chevy Tahoe- Soft Brake Pedal


Try having the dealer flush and bleed your system. It is very hard to bleed ABS systems yourself and have safe brakes that still work afterward. Bleeding non-ABS brakes yourself is easy not the same for ABS brakes. Valving, sensors and what-not require a tech and the correct equipment in my opinion. You do it wrong and you could ruin your ABS system. Do that and see if they firm up. I replaced my brake shoes/pads at the same time all new everything in back, drums/springs everything and new rotors up front. then I had the chevy dealer flush, refill and bleed system. Stiffer pedal and brakes work better. Keep in mind the brakes on 99 Tahoes are inaedequate, require new rotors often, heat up and fade/glaze pads regularly. I replace my pads long before they wear down because they glaze up and start fading early. I'll rough em up once maybe, next time, new ones. Every two brake jobs, new rotors for me. Just how it is. They will stiffen a bit and work better but they will never be awesome brakes. Just how it is on 99 and earlier Tahoes. Hope it helps. Very important to bleed correctly though. I'll bleed my 83 Toyota 4x4 myself but not the Tahoe.

Aug 06, 2009 | 1999 Chevrolet Tahoe

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

92 dodge van rear ABS-brake and ABS lights on/can't reset?


Its probably how your bleeding your brakes, but first make sure the bleeding nipples are facing upward. You should bleed diagonaly, front pass wheel then rear driver wheel. Then front driver wheel and rear pass wheel. The abs light has its own computer your have to get it scanned to clear the codes and turn off the light

Mar 18, 2009 | 1992 Oldsmobile Ninety Eight Regency

Not finding what you are looking for?
1995 Mercedes-Benz S-Class Logo

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76109 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...