Question about 1995 Chevrolet Monte Carlo

1 Answer

Cant gat last bolt 2 come out of starter.

Got it loose , but the starter is keeping it from coming out

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 62 Answers

Try pulling on the bolt while moving the starter, sounds like it got jammed.

Posted on May 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

02 mountaineer I removed all bolts from the starter and now it wont come out


Check photos for the starter to see how many bolt holes you have. Sometimes they are overlooked. The starter bendix can extend and then not retract. This can cause problems in clearing the flywheel. If you disconnect the battery terminal, take a large socket on the front crankshaft bolt and move the crankshaft back and forth to shake the starter bendix loose from the flywheel.


As a last resort, sometimes taking the end bolts out of the starter will allow you to pull the starter off in pieces.

Oct 24, 2014 | 2002 Mercury Mountaineer

2 Answers

96 maxima harmonic balancer broker and cant get bolt loose to replace


If no access to an air gun, then do it old style: take the starter out and wedge a large screwdriver or pry bar against a tooth of the flywheel- two people may be needed for this. One can hold the flywheel tight, while the other attacks the crank pulley bolt. Or you could wedge a piece of wood in the starter mounting hole, tight against the flywheel. A stick of split firewood has the right angles- after a couple of attempts, the wood will wedge itself good and tight, keeping the crankshaft from turning. You really need a 1/2 inch breaker bar and socket for that bolt. It is torqued down to about 160-200 ft. lbs.

Apr 07, 2014 | 2000 Nissan Maxima

1 Answer

How do you remove the starter from 2001 grand caravan. i just cant get to the nut thats on top of the starter. is there a secret way to get to it?


what nut on top of starter ? you have 2 bolts that run's from bottom of starter upwards to engine block. after they come out starter will be loose then it will drop some to get the pos. cable,2 small hot wire's off......then finish dropping starter ---- put back in reverse order......

Dec 17, 2010 | 2001 Dodge Grand Caravan

1 Answer

Removed starter bolts but cant get it to drop didnt know if need to take loose motor mounts to raise engine for clearance


Some times you need to move the steering in one direction or the other to get room to move the starter. Look on the New starter for a Rearward bolt coming from the Trans side. Sometimes you have 3 starter bolts.

You don't need to lift the engine.

Jul 01, 2010 | 1997 Mercury Grand Marquis

2 Answers

How do I install starter for 2000 GMC Sonoma. This is a 4 cyl 2 wheel drive pick-up


e
Removal & Installation
2-Wheel Drive
- 2.2L Engine
  1. Remove or disconnect the following:
    Negative battery cable Front exhaust pipe, if necessary for access Starter heat shield, if equipped Brace rod from the front of the engine and the bell housing Drivers side wheel to access the starter motor wires and the starter motor attaching bracket-to-engine bolt through the opening in the wheel well Wires from the starter solenoid Attaching bracket-to-engine mount bolt Starter-to-engine block bolts. When removing the last bolt, be sure to support the starter to keep it from falling and possibly injuring you. Starter and shims (if equipped) from the vehicle Bracket from the starter assembly, if equipped

    e12f2d1.jpg

    Fig. Starter motor and related components - 2.2L engine

To install:
  1. Install or connect the following:
    Bracket to the starter, if removed. Tighten the bracket nuts to 97 inch lbs. (11 Nm). Starter and shims (if equipped) into position in the vehicle and thread one of the retaining bolts to hold it in position. Bracket-to-engine mount bolt (loosely), if equipped Starter mounting bolt, then tighten all mounting fasteners to 32 ft. lbs. (43 Nm) Wiring to the solenoid Brace rod and tighten the retainers Front exhaust pipe and tighten the fasteners, if removed Starter heat shield, if equipped Driver-s side wheel, if removed Negative battery cable

Hope helped with this (remember rated this help) Good luck.

Nov 18, 2009 | 2001 GMC Sonoma Extended Cab

1 Answer

My truck won't start and ineed to change the starter


Start by disconnecting the battery. This is important or you could loose fingers.

Underneath the engine, on the passengers side of the vehicle is where the starter is located. Sometimes the exhaust system can get in the way, if it's stock it will probably be ok. There will be two bolts that hold the starter in place. Keep them separate as one may be longer than the other. Be careful when removing the second bolt as the starter is kind of heavy and you don't want to have to take a trip to the dentist as well. Some starters also have a rear brace on them that goes from the starter to the block. This may or may not be there, I don't recall seeing them on the last one of these I worked on. There will be a solenoid bolted on the top of the starter. It's a smaller cylinder than the starter body itself. Leave that connected to the starter. Make a diagram of which wires went on which post here. There are 3-4 places for wires. There should be 1 - 2 3/8 inch posts and 2 1/4 inch posts. Like I said diagram where the wires go so you can get it hooked up again. Don't let the starter dangle by the wires, it's hard on them. Also there may or may not be some shims under the starter, between the starter and the engine block. Keep them if there are, you may need them. Carefully check all the dimensions of your new starter to make sure it will fit.

Nov 09, 2009 | 1992 GMC Sierra

1 Answer

Cant get last bolt out of alternator for replacement


put your socket in hold from on top take a hammer or o heavt object and knock it til it comes loose. if that doesnt work buy a spray a a hardware store that loosens stuck bolts

Mar 20, 2009 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Why does my starter bolt keep coming loose


Have you tried “lochtite strong hold” thread sealer and allowed 8 hours to setup?

Jul 06, 2008 | 1992 Mitsubishi Eclipse

Not finding what you are looking for?
1995 Chevrolet Monte Carlo Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...