Question about 1995 Dodge Dakota

1 Answer

Abs and break light flashing 10 times then pause then ten times again. this is happening when i drive all the time. what does this mean? 95 dodge dakota slt 4x4 v6

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 14,036 Answers

Have abs brakes scan it could be a bad wheel sensor.or abs failure dont keep driving.

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to go about fixing a code my 89 Dodge D 100 2


By cycling your ignition key 3 times in 5 seconds command codes to be flashed through check engine light key off,on,off,on then watch lamp first series is the ten digit and pause then single digit So a flash flash pause flash flash pause would be code 22 at the end of display is code 55 (end of message).

Aug 31, 2014 | Cars & Trucks

1 Answer

Abs light stays on and is flashing a i think acode


hi Robert

you can check the ABS fault code as following:

switch ignition on and wait for the abs light to start to flash.
it will flash in long and short flashes, long flash stands for ten, short flash stands for one, there is a short pause in between, and long pause after each code, take a note of the code and Google it
good luck
9ba390f1-ca01-44ac-85b4-4603e1244a3a.jpg

CODE 12 CODE 21

Jan 17, 2014 | 1993 Ford Ranger SuperCab

1 Answer

Abs light on


read the FSM?
read the TSBs?
car off then on, you mean starting,
and the only difference is the time off, ?
the abs glow, key on?, is self test passing, if you flip key fast and drive it crazy , you are the problem. let the poor thing finish its tests, key on, then start car.


the tests are in the FSM read it, ABS is complex.
ill try to look up 95, on line.

the 95 ABS has its own diagnostic jumper plug
did you jumper it and see if there are any DTC error codes, flashing out.?

the FSM page 19-68-70

see those flow charts, did you follow it?
did you see the list of 10 causes, for lamp stuck on? (not DTC)
one is alternator stuck on. charge lamp on, running.

here you can look for free. RTM,
http://hondatech.info/downloads/Auto/Manuals/Accord/

Oct 08, 2013 | 1995 Honda Accord

1 Answer

2002 dodge intrepid sxt 3.5l. what does 10 flashes of check engine light mean?


Are you sure is not 5 flashes with a short pause in between and then 5 more flashes? Code 55 indicates the end if the diagnosis.

Mar 02, 2013 | 2002 Dodge Intrepid

1 Answer

Engine light on 1988 dodge caravan


Cycle key to on (not start) then off, then on, then off, then back on & leave in on position. Now watch check engine light and it will begin to flash. When it does, it will flash a certain number of times, then pause, then flash some more. Count those flashes and write them down. All numbers will be 2 digits. For example: flash,flash,flash, pause, flash ,flash,flash. will be code 33. Then small pause starts next set of numbers. When you get 5 flashes, pause, 5 more flashes, =55, that means end of message/codes. Do that a couple of times until your sure of the number(s) and get back to me/us and we will be able to help better from the codes.Saves time and money.

Mar 09, 2012 | Dodge Cars & Trucks

1 Answer

My check engin light for my 2002 dodge neon is flashing 10 times. what does this mean?


I believe the flashes come in 2 groups. Some number, a pause, then more flashes. If you're getting 5, pause, 5; that means there are no errors. I could be wrong, because I thought cars newer than '96 had OBDII systems that need a reader to determine problems. You can get them read free at some auto parts stores (AutoZone for one). I hope this helps you.

Oct 24, 2009 | 2002 Dodge Neon

2 Answers

I have a 1989 s-10.The parking brake light blinks six times,pauses then flashes again.I was wondering what trouble code that would be???Thanks.


RWAL Fault codes
Codes for Dodge RWAL, Ford RABS and GM RWAL applications are similar but have a few differences:
  1. Should not occur (replace the controller if it does)
  2. Open isolation valve circuit or defective ABS module
  3. Open dump valve circuit or defective ABS module
  4. Grounded or closed RABS or RWAL valve switch
  5. Excessive actuations of dump valve during ABS braking
  6. Erratic speed sensor signal
  7. Shorted isolation valve or defective ABS module
  8. Shorter dump valve or defective ABS module
  9. High resistance or open speed sensor circuit (resistance should be 1000 to 2500 ohms)
  10. Low speed sensor resistance (Dodge & Ford only)
  11. Open speed sensor circuit (GM only)
  12. Stop lamp switch circuit (Dodge & Ford)
  13. ABS module speed processor (Dodge & Ford only)
  14. ABS module program (Dodge & Ford only)
  15. ABS module RAM memory failure (Dodge & Ford)
To manually clear a stored fault code on GM and some Dodge trucks with RWAL, remove the ABS fuse or disconnect the battery for 5 seconds. Ford RABS codes will automatically clear when the ignition is turned to the off position.

Aug 26, 2008 | Chevrolet S 10 Cars & Trucks

1 Answer

2000 Dodge Stratus


The first thing I would do is check the Transmission Control Module (TCM) for stored codes. To call up codes, cycle ignition switch on, off, on, off and on within 5 seconds. Stored codes will be indicated by flashes of the check engine lamp. The codes will be indicated as two digit numbers, with a four second pause between codes. An example of a code scan is as follows:
  • Power Loss/Check Engine Lamp illuminated for approximately 2 to 3 seconds as a bulb check, then turns off.
  • Lamp flashes 2 times, pauses, then flashes 6 times.
  • Lamp pauses for approximately 4 seconds.
  • Lamp flashes 3 times, pauses, then flashes 1 time.
This would indicate that code 26 and 31 are stored. The lamp will continue to flash until all stored codes have been displayed.
If we are lucky we'll get some codes to work with. This will show you any transmission codes.

I found that a code 31 on a 94 Voyager indicates an evaporative emissions problem, but I'm not sure whether that code applies to your car as well. Have the ECU scanned at AutoZone and see what comes up. They'll do it for free and will give you the codes. Then you can post them up and we'll see what we can do about them.

Jul 22, 2008 | 2000 Dodge Stratus

Not finding what you are looking for?
1995 Dodge Dakota Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8531 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...