Question about 1987 Peugeot Liberte

1 Answer

Starter motor peugeot 106

Started car in gear starter mortor stuck how do i release it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 234 Answers

Aveu tried puting car in gear and just rocking it bath and forward

Posted on May 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Starter motor


problably the anker goes not direct back in its housing.
so he does more turn then he can handle.when you turn the ignition,
a gear in the starter comes forwart and turn the flywheel.when the,
fly wheel runs higher then the gear off the starter it flips back in its ,
housing.some times this dont happen and makes a specific sound.
replace the starter.

Feb 17, 2014 | Peugeot 306 Cars & Trucks

1 Answer

Turn key motor start but starter eeps turning over stops when put in gear


Sounds like the Pinon(gear) in the starter is getting stuck and not disengaging when you release the key. It may need to be lubed up or replaced.

Dec 07, 2012 | 1999 Ford Escort

1 Answer

How do we time a 1998 1999 106 peugeot diesel car


if i remember rightly then their are holes in the timing gears which you push a 8 mm drill bit through to lock the gear wheel for the timing pump and the camshaft into position ,the crankshaft keyway points to the top of the engine ,make sure you turn engine over 360 degrees after fitting the new belt by hand to ensure the valves clear ,look at the gears and the back behind the gears for the locating hole ,think the cam is 90,to the right and the pump is to the left m,sorry iam and suffering from old timers so memory is not what it was

Oct 06, 2012 | Cars & Trucks

1 Answer

Just changed my clutch on my peugeot 206 1.6 now my car wont start what are the likely things wrong


Not a Peugeot expert, but there should be a safety switch to keep you from cranking the engine in gear.

Jul 12, 2012 | Peugeot 206 Cars & Trucks

1 Answer

Peugeot 106 won't start


Hi and welcome to FixYa!

If your car doesn't even crank please be sure that the battery has a good charge. If the battery is good then the problem will be on the starter itself.

If the battery and starter is good then the problem may rely on the fuel pump itself so this will require replacement for the car to work again.

Hope this helps and thank you for using FixYa!

Nov 29, 2010 | Peugeot Liberte Cars & Trucks

1 Answer

Gears stick


If your car is a manual gear change, your clutch may need adjusting or repair or the gearbox oil may need changing.
If your car is an auto check to see if you are using the correct transmission fluid , Peugeot autos do not use normal ATF and will fail if the correct fluid is not used.
Hope this helps Marshall

May 26, 2010 | 1990 Peugeot 405

1 Answer

Where do you put the gear box oil in a peugeot 106 1994?


there is a plug on the end of the gearbox with a square hole in it this is the level and refill plug
fill up untill oil starts coming out of the filler

Nov 02, 2009 | 1991 Peugeot 405

2 Answers

Not starting when warm


when u turn the ignition on before firing the starter do you hear a humm? if not maybe petrol pump or auto choke playing up, check ur fuses, under the bonnet2

May 29, 2009 | 1991 Peugeot 405

1 Answer

It wont start


That sounds more like a dead battery than anything else. The bendix, the bit that engages the starter to the flywheel, usually goes bad a bit more slowly and causes more dramatic persistent grinding. A bad starter is also possible, as are bad battery cables. The starter mortor and bendix are both replaced when you install a rebuilt starter. If a jump start doesn't solve the problem, and connecting a jumper cable directly from the + battery terminal to the starter motor doesn't help then replace the starter. If it does help, then the problem is probably the battery cables.

Mar 12, 2009 | 1991 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

429 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Wahs Team

Level 2 Expert

205 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...