Question about Dodge Dakota

1 Answer

Need to find the location of the heat sending unit on the engine so i can replace it

I need to find the location of the Heat Sending Unit on the engine of a 1999 dodge dakota 3.9L, V6 magnum

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

By the thermostat hausing

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to know where is the oil sending unit at on my 2008 Chevy impala


On Chevrolet Motors, it depends on which engine you have and that will vary the location... Start by looking close to the Oil Filter. On the 5.7 Liter engines, it is on the Back side of the Engine, On some of the smaller, it si located below the Exhaust.

Apr 05, 2013 | Cars & Trucks

1 Answer

I need to replace the oil sender switch on my 2002 Buick La Sabre


first need to buy oil pressure sending unit 3/8 deep socket remove oil pressure sending unit you need teflon tap sealer for oil sending unit threads.okay to replace oil pressure sending unit.you need safe raise support vechicle locate oil pressure sending unit next to the oil filter.disconnect oil pressure sending unit wire connector then use oil pressure sending unit 3/8 socket remove the sending unit.then take new oil pressure sending unit use teflon tape white plumbers tape or use thread sealer apply to the oil pressure sending unit threads then install new oil pressure sending unit and reconnect electrical connector to sending unit.then crank engine check for oil leak if all is good lower vechicle back to ground wait several minutes check engine oil level.you good to roll.

Feb 09, 2013 | 2002 Buick LeSabre

1 Answer

Where is heat sending unit ford f250 2002 located on engine


Do you mean the temp sending unit for the gauge, and also what engine do you have ?

Feb 01, 2013 | Ford Cars & Trucks

1 Answer

Need to replace the heat sending unit on 1991 buick regal but cannot find where the part is located can you please advise me of where the heat sending unit is


If you mean the engine temperature sending unit, it should be on the cylinder head and has a single wire attached to it. It looks a little like a miniature spark plug with a black insulation. To simplify your search, buy the new one and look for the same thing on the engine.

Feb 02, 2011 | 1991 Buick Regal

1 Answer

My van has poor heat and changed antifreeze and temp hand stopprd working does that effect heat the temp sending unit


the sending unit will not affect heat but if its broken it will effect the fuel control by giving computer false info, i dont think theres a problem with the temp unit, i think the thermostant is bad and is stuck open or you are very low on coolant, if the thermostat was stuck open then you would get some heat not very hot and would take a long time to get heat. i would start by replacing the thermostat, it is very important to bleed air from system after coolant change or thermostat replacing, after filling run engine until fan turns on , let cool some to release preasure then remove cap start engine and top off, drive for 15min then park let cool and recheck coolant, hope this helps,

Dec 19, 2010 | 2001 Oldsmobile Silhouette

1 Answer

Thermostat was replaced on a 99 ford explorer sport but now ithe heat gauge on the car not coming on ???


the temp sending unit is located close to the thermostat. check to see if it came unplugged or clean the connector it may have corrosion inside causing it to lose contact othertwise u may need to replace the sending unit. leave comment

Jun 27, 2010 | 1999 Ford Explorer

2 Answers

The tempertature gauge does not work on my jeep what may be the problem?


Could be the coolant temp sensor:


d3ad89d.gif
4.0L engine shown




7a3db5f.gif
5.2L engine shown



To test it:

Perform this test on a cold or cool engine.
  1. Disconnect the negative (-) battery cable.
  2. Unplug the electrical wiring from the sending unit.
  3. Using an ohmmeter, measure the resistance between the terminal and the sending unit's metal body
    1. Infinite resistance or zero resistance: the sending unit is bad, replace the sender with a new one.
    2. Other than infinite or zero resistance: continue test.
  4. Remove the temperature sender from the engine.
  5. Position the sending unit so the metal shaft (opposite end from the electrical connectors) is in a pot of water. Make sure that the electrical connector is not submerged and only the tip of the sending unit's body is in the water.
  6. Heat the pot of water at a medium rate. While the water is warming, continue to measure the resistance of the terminal and the metal body of the sending unit:
    1. As the water warms up, the resistance goes down in a steady manner: the sending unit is good.
    2. As the water warms up, the resistance does not change or changes in erratic jumps: the sender is bad, replace it with a new one.
  7. Install the good or new sending unit into the engine, then connect the negative battery cable.
  1. With the engine cold, remove the ECT sensor.
  2. Immerse the tip of the sensor in container of water.
  3. Connect a digital ohmmeter to the two terminals of the sensor.
  4. Using a calibrated thermometer, compare the resistance of the sensor to the temperature of the water. Refer to the sensor resistance illustration.
  5. Repeat the test at two other temperature points, heating or cooling the water as necessary.
  6. If the sensor does not meet specification, it must be replaced.

75c7153.gif
Submerge the end of the temperature sensor in cold or hot water and check resistance


082c068.gif
Temperature-to-resistance relationship of the ECT and MAT sensors

Apr 28, 2010 | 1995 Jeep Grand Cherokee

3 Answers

Where is the oil pressure sending unit located?


The pressure sending unit is located on the passenger side rear of the engine just above and slightly to the left of the filter and filter housing.

May 10, 2009 | 2000 Buick LeSabre

5 Answers

Where is the oil pressure sending unit on 2004 dodge stratus?


per the Haynes manual for the 95-05 Dodge Stratus on the 2.0L & 2.4L DOHC 4 cyl engines, the oil pressure sending unit is located at the left end of the rear side of the block. On 2.4L SOHC 4 cyl engines, the sending unit is located at the left end of the rear side of the block. On 2.5L & 3.0L V6 engines, the sending unit is located on the oil filter housing, on the front side of the block. On 2.7L V6 engines, the sending unit is located at the left end of the rear side of the block. To access it, remove the heat shield.

Jan 23, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

261 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...