Question about 1997 Mercury Sable

1 Answer

Where is the vehicle speed sensor located on a 95 mercury sable 3.0...please be very specific and a diagram or picture would be greatly appreciated.

Posted by on

  • Woody J Hiatt May 11, 2010

    Bring it over and I'll show you but it is normally on the transmission
    and the Auto zone web site may be as specific as your request. Type in
    speed sensor and find part location. I ain'tgoing to do fit or you. You
    learn how or go to your local library and check out a service manual.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,669 Answers

It is in the end of the transmission on the top. Look where the passenger side CV shaft comes out and look back toward the drivers side from there. It is on top tucked under the rear exhaust manifold.

Posted on May 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 94 mercury sable speed sensor located ?


in the transmission but if you have 4 wheel abs then each wheel would have speed sensors as well.

Aug 03, 2014 | 1994 Mercury Sable

1 Answer

How do I locate the turbine speed sensor on a ford mercury sable 2001


I don't have a picture--but recall that it may be
on top of the trans case

Try You Tube & put that in there after you get to
the site

Nov 29, 2012 | 2001 Mercury Sable

2 Answers

Where is my throttle position sensor located on my 1995 mercury sable 3.8l


The Throttle Position Sensor is located at the top center rear of the engine, on the throttle body.
Here is a diagram showing where the TPS is located on this vehicle.
Hope this helps...

9_9_2012_1_02_38_am.gif

Sep 08, 2012 | 1995 Mercury Sable

1 Answer

What is the component atached to the underside of the spare tire well on my 1996 Mercury Sable? It has 3 tubes runing to or from it. 1 is rubber and 2 are metal. The brackets that held it up rusted thur...


MERCURY SABLE , manufactured by FORD MOTOR COMPANY had a problem with SUSPENSION:FRONT . AT HIGHWAY SPEEDS, VEHICLE SWAYS AND VEERS EXCESSIVELY IN MODERATE CROSSWINDS. *AK.Vehicle Identification Number (VIN):1MEHM55S31A. MERCURY SABLE 2001 problem was reported in ANDOVER, MA. Original Owner. Vehicle was purchased on 20000901. Vehicle was using ANTI-LOCK BRAKES.Vehicle was using Cruise Control.MERCURY SABLE 2001 drive type:FWD. FUEL SYSTEM:N/A. FUEL TYPE: GAS. VEHICLE SPEED: 65 mph.

May 25, 2011 | 1996 Mercury Sable

1 Answer

1998 mercury sable.need to change vss,does this have to be done from underneath vehicle'am a little afraid of breaking exhaust bolts


Vehicle Speed Sensor (VSS) Removal
  1. Raise and suitably support vehicle.
  1. Remove dual converter Y-pipe from exhaust system. -
  2. Remove heat shield from transaxle.
  1. Disconnect vehicle speed sensor (VSS) electrical connector.
  1. Remove VSS retaining bolt and remove VSS from transaxle.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten VSS retaining bolt to 5-8 Nm (45-70 lb-in).


    ad0002a.gif

Mar 22, 2011 | 1998 Mercury Sable

1 Answer

Mercury sable code P0500 P


Basically this means that the vehicle's speed as read by the Vehicle Speed Sensor (VSS) is not working properly.

Symptoms of a P0500 DTC may include:
* loss of anti-lock brakes
* the "anti-lock" or "brake" warning lamps on the dash may be lit
* the speedometer or odometer may not work properly (or at all)
* your vehicle's RPM limiter may be decreased
* the shifting of an automatic transmission may become erratic
* other symptoms may also be present

Causes: A code P0500 may mean that one or more of the following has happened:
* The Vehicle Speed Sensor (VSS) is not reading (functioning) properly
* There is a broken/frayed wire leading to the vehicle speed sensor
* The vehicle's PCM is not correctly configured for the actual tire size on the vehicle

Possible Solutions: The simplest thing to do is to reset the code and see if it comes back.
Next, check all wiring and connectors that lead to the speed sensor. The location of the sensor depends on your vehicle. The sensor could be on the rear axle, transmission, or perhaps the wheel hub (brake) assembly.

If the wiring and connectors are OK, then check the voltage at the speed sensor. Again, the exact procedure wil depend on your make and model of vehicle.

If everything looks OK, replace the sensor.

Hope this helps (remember to rate this answer).

Mar 15, 2011 | 1999 Mercury Sable

2 Answers

EGR DP sensor location on a 1999 mercury sable 3.0 engine


This sensor delta pressure feedback sensor for the egr is located on the top right side of the intake manifold, heres a diagram that will also help in locating this sensor, hope this is helpful. johnjohn2_12.gif

Nov 07, 2010 | 1999 Mercury Sable

1 Answer

Can not locate the vehical speed sensor on my 95 sable 3.0


It's on the transmission, usually a 2 pin connector

Jan 28, 2010 | 1993 Mercury Sable

1 Answer

Need diagram/schematics for fuse panel on a 1988 mercury-sable


Ford Taurus/Sable 1986-1995 Repair Information
Fuse Panel and Fuses

721188f.jpg

Fig. 1: On most vehicles covered by this information, the fuse panel is located to the left of the steering column, attached to the instrument panel

aaffea7.jpg

Fig. 2: Fuse panel/block location-Early model Taurus shown

0a488be.jpg

Fig. 3: Location of fuses and the circuits they protect-1995 vehicle shown

More details you can find in autozone.com (free register) with 46 wiring diagrams about Mercury Sable.

Hope helped with this (remember rated this help) Good luck.

Nov 09, 2009 | 1988 Mercury Sable

Not finding what you are looking for?
1997 Mercury Sable Logo

346 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...