Remove rear axles bushings - 1995 Geo Tracker

If car is rear wheel drive.....Check you Universal joints on your driveshaft

Could also be Trailing Arm bushings.if you have coil Springs on your rear axle. These bushings keep the axle from rotating. So when you do that Clutch jumpy thing the axle is trying to rotate and with bad bushings it could be 'banging'

check steering/suspension for loose/worn out parts and replace if needed. check tires for belt separations and replace if needed. if you have a steering damper check and replace if needed.

Remove the road wheels, remove front hub from stub axles, remove the cotter pin nut and drive out the pin, remove the welch plug on the top of the king pin and with a drift drive the pin through the axle, press the old bushes from the stub axle and press in new bushes, ream the bushes till the king pin will just slide in .Then assemble make sure there is no play between the pivot bearing and stub axle use shims if required.

NOPE FIRST TURN OFF THE AIR SUSPENSION IF EQUIPPED THEN YOU REPLACE SHOCKS BY SUPPORTING REAR AXLE WITH A JACK.AND REMOVING TOP AND RETAINING NUT WASHER BUSHING.THEN REMOVE BOTTOM RETAINING NUT WASHER BUSHING THEN REMOVE SHOCK.

I bought the bushings on ebay from buyer friesian55 he has a pair of axle bushings for 100 and free shipping. Which any mechainc would be able to install

First the wheel has to be removed. Then it's a good idea to remove the braking hardware(Shoes, springs etc.) for these will have to bre cleaned or replaced later in the process. There will be 4 or 5 hex head bolts circling the axle, remove these and at the same time place a small tray underneath to catch any small amount of fluid which may drip out. Next pry the axle out with your hands or a couple of matching prybars at 3:00 and 9:00 equally. The seal may be removed using a long, large flat head screwdriver blade. Use extra care not to scratch(score) the seal housing. The new seal should be installed using a seal and bushing installer kit, however, it may be done by using the old seal flipped iover and taped at a rotational method. Make sure after all is put together to measure the fluid level. This is done by placing your pinky finger into the filler hole . If there is enough fluid to coat your fingers firest knuckle than you're all set. Thank you, Dana

IF YOU NEED THE REAR AXLE BUSHINGS THEIR AVAILABLE ON EBAY . I USED THEM ON MY 2004 AVEO AND THEY WORK FINE

i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal

1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.

1. Remove rear stabilizer bar as outlined.

1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .

1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .

1. Lower the hoist and axle housing until the rear springs are released.

1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
   -----------------------------------------------------------------

Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.

1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.

Installation

1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.

1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).

1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).

1. Lower vehicle.

-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .

1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.

1. Remove rear stabilizer bar as outlined.

1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .

1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.

1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .

1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.

1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .

-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).

1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
2. Support the rear axle assembly .
3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
4. Unsnap parking brake rear cable and conduit from upper arm retainer.
5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.

------------------------------------------------
Stabilizer Bar
WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal

1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .

1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.

1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

HI, this noise can be caused by worn shocks,even if the bushings look good, you can remove one of them and check if is hard to constracts ,if not they must be replaced,

that bushing has to be driven and removed from the inside of the case, I believe. Some trans shops can get bushing kit.

94-Up
K85901 part # thru TransTec