Question about Daewoo Nubira

2 Answers

My rear wiper dont work at all on my Isuzu Rodeo 98, change motor but still dont work, all fuzes o.k i dont know where is relay location

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

If you have a 98 or newer with the glass that flips up and door thar swings open the problem is in the wiring in the door hinge. there is a small rubber tube the wire runs through. pop the tube out of the door and the body and remove the tape holding the tube in place. you must do this as i missed it the first time around and didnt find it as the break was deep in the tube. i had 3 wires broken in mine and from the owners i know this seems to be a common problem.. good luck

Posted on Mar 16, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Daewoo Master
  • 450 Answers

The intermitant relay is right side small black box under bonnet inner gaurd to firewall (bulkhead) area there is a nother relay next to it but more inbound (closer to middle)
there is no other relay but here is wiring diagram
sorry about the size could be the stalk switch or wiring problem
my rear wiper dont work at all on my Isuzu Rodeo - 20d01bf.jpg

Posted on Jun 29, 2009

  • Steve Hurc
    Steve Hurc Jun 29, 2009

    should be power at terminal 6 green/white wire at motor with ignition on

    earth is term.3

    power at terminal 1(high) speed

    power at terninal 2(low) speed

    terminal 5 goes to intermitant relay

    terminal 4 not used

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 isuzu rodeo where are the rear wiper relays


one more silly easter egg hunt, seems that is all we get.
now....sad..
and guess what most cars have no such thing.
ill pretend you did say that, and said
"my rear wipers are totally dead. why." HARK A REAL QUESTION.?
ANSWER:
A fuse blown.
marked rear/wiper washer 10 amps.
blown.
there is no relay have schematic here.

poof i the pudding.... below.

26158809-ump5fefdwjhjx4o31tvgr1id-3-0.jpg

Apr 10, 2016 | 1999 Isuzu Rodeo

1 Answer

How do you replace the wiper motor on a 98 rodeo


the front or rear, no way for me to guess?????
unbolt it and replace it.
start at the arms and work inward works.

ill toss coin land on front.
ill read the FSM online for you, so can you , but here ill do it.

Motor
  1. Disconnect the negative battery cable.
  2. Disconnect the wiper power motor connector (2).
  3. Remove 4 mounting bolts.
  4. Remove the nut of the wiper motor shaft, and disconnect the linkage.
  5. Remove the windshield wiper motor (1).
To facilitate the removal of the nuts, be sure to put out the tip portion of the linkage sufficiently through the mounting hole of the motor by sliding the wiper blade slowly.


my guess is this the most easy motor on earth to change.
its in plain view, not burried deep in a cowl.....

it's
easy-peasy-japanesy..

Feb 22, 2015 | 1998 Isuzu Rodeo

2 Answers

2001 rodeo, wiper problem may be caused by a bad relay in circuitry?


first off all cars have a FSM factory service manual.
and the chapter on wipers even tells you how it works.
and with a full schematic.
why work blind, just guessing and flaying about like robot in lost in space. (funny to watch tough)
why do an internet search and read 10000, wrong ways or wild guessing to do something , do you like lies and pain, that it.
here, its bad muffler bearings, doing that....
its a motor and a switch.
if intermittent, then it has what is called a intermittant controller module. and what is that, a timer and a transistors is what that is.
a motor, switch and timer.
simple as can be, a DC motor. if you know what DC motor is
then you know it needs to be controlled,
after all it would break the wipers in half if not controlled
so lets look at your car, ever heard of mitchell's DIY online
this is a virtual FSM book
we look there first to see how yours is wired, guessing will NOT WORK, in electrics, sorry but IT DONT
if you dont know how something works how can you fix. it.
sure wild guessing.
when dont guessing and wasting big bucks in worse time.
we get the drawing.
and see what.
answering for 2001 Rodeo , no SPORT RODEO.
cb17 is fuse wiper
feeds the switch wiper
if high works and low works an not int. then what is bad the interm. controllers
marked alarm relay control unit
did someone defeat the ALARM , if yes, wana bet that killed dead
the intermittent wipers, sure would.
the red arrow is INT wire to alarm box.
be wise of all to check fuses first
then check for alarm hacks.!!!


14006666-w5nwpkyfhmoujp5dymd2xtff-4-0.jpg

Aug 15, 2012 | 2001 Isuzu Rodeo

1 Answer

Where is the ECM relay located on a 98 Isuzu Rodeo


Emission control mechanism or relay is either a vacuum plunger type or a relay switch electrical plug that controls vacuum for the smog. Go to the parts store and look at one and ask where it goes or just trace it. This stops from buying one if you remove the hose or connector and the same problem is still there!

Jul 26, 2012 | 1998 Isuzu Rodeo

2 Answers

Rear wipers on rodeo wont turn off


Hello! I suspect a defective rear wiper switch...However they are very expensive...This is an unusual fault due to the off in 5 minutes factor...Is that a consistent time period or does it change? I would first remove the wiper switch...Pull the connectors...And spray with a product called DeOxit from Radio Shack...If that doesn't help... Located behind the glove box, up high, is the alarm relay control module...Take it out and visually inspect the circuit board with a bright light view the solder side for cold joints or damage...See photo of Wiper switch below...They run about $200 for a new one...I'd look for a used one...Guru..saailer




2_11_2012_8_16_08_pm.jpg

Feb 11, 2012 | 1998 Isuzu Rodeo

1 Answer

Im working on a 1999 Honda passport v6 4wd. The rear wiper motor doesnt work, I replaced the wiper motor with a new one. Still doesnt work. I inspected the wiring and found no physical damage. The rear...


Richard, I am actually going through some troubleshooting with the rear wiper on my 98 Passport. Mine runs . . . it just doesn't stop where and when it should anymore. There are some Rodeo/Passport enthusiast sites that have some threads on this. Many of them refer to replacing the Alarm Control Module (where the wiper relays are) or just removing/replacing the bad relays on the board if you know how to solder.

I've never soldered before in my life, but I replaced the relays on my Alarm Control Module the other day. Unfortunately it did not fix my problem--so I may have a bad motor or switch. But it might be worth a shot to look at the relays as your next item. It took me a couple hours to do it, but it wasn't too terrible once I figured out what I was doing.

Here is a link to the forum that helped me: http://forum.planetisuzoo.com/viewtopic.php?t=5608

You might be able to find a workshop manual online.

Nov 23, 2010 | Honda Passport Cars & Trucks

1 Answer

Have a 2000 Isuzu rodeo v6. When I go to start


Sounds like the motor has shorted and is receiving an intermittent signal. I would try a pick n pull salvage yard and replace the motor; it should not cost much at all.

Aug 26, 2009 | 2000 Isuzu Rodeo

1 Answer

1998 Rodeo Transmission Speed Sensor


i think near rear of trans near output shaft

Oct 27, 2008 | 2000 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,498 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

yadayada
yadayada

Level 3 Expert

75797 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...