Question about 2002 Chrysler Sebring

2 Answers

Key won't turn and steering column is locked up.

Posted by on

  • dustang25 May 11, 2010

    a couple of silly questions here. have you tried shaking steering wheel hard while trying to turn key also try to wiggle shifter, making sure it is fully engaged in park. they are interrelated. you should be able to get it.. dustang

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Try spraying wd40 or other light oil into keyway. this did the trick for me!

Posted on May 10, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 22 Answers

Try jiggling the steering wheel while turning key

Posted on May 09, 2009

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1214 Answers

SOURCE: Steering column frozen

You may have bound the steering wheel up against the locking mechanism.

Put the key in the ignition, and try to turn, while attempting to rotate the steering wheel to the left or right. When you rotate it the right direction, the key will turn fully and you can start the car.

Posted on Jan 16, 2009

  • 1 Answer

SOURCE: 2000 Chrysler T&C Ignition Switch Locks up

I used a combination of the above on my 2003 Town and Country but I did it the easy way. I simply placed a screwdriver in the ignition where the key goes and I tapped the screwdriver with a hammer (LIGHTLY). Apparently, this freed the stuck pins and everything works fine now. I then sprayed WD40 into the ignition so it will, hopefully, not stick again.

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Steering column won't unlock


The front wheels are at a angle putting pressure on the steering lock , rock the steering wheel from side to side while turning the key.

Mar 27, 2015 | 1996 Toyota Camry

1 Answer

2003 honda accord/ key wont turn,steering wheel is locked


To fix your problem, you have to turn the steering wheel either to the left or right as much as you can, then try to turn the key in the ignition. When the steering wheel locks, the key won't turn. By manually holding the steering wheel out of the lock position, the key will turn again and you're steering column will be back to normal.

Oct 19, 2011 | 2003 Honda Accord

1 Answer

Key stuck in ignition but it will turn, and steering column won't lock and car won't start.


you most likely have a bad key switch cylinder assembly. you can try to spray wd40 solvent into the switch before you have the switch replaced,but sometimes it's a switch replacement that repairs the problem. have you inspected your ignition key to look for damage to the key itself? try a spare key to make sure it's the key,and not the key switch. you can also try turning the key while turning the steering wheel at the same time to get the key to work.sometimes the switch locks when parked in a bind,such as on a hill,or against a curb and so on. try this 1st before you have the ignition switch replaced. AAA auto club,if you're a member covers part of the replacement costs for a replacement switch also. you may have coverage through a cell phone also.one more thing to try, if you have a tilt steering column,try to reposition the steering wheel to see if you can get the key to turn. remember never force it enough to break your key off into the switch! thank you for choosing fixya.com!

May 13, 2011 | 2002 Chevrolet TrailBlazer

2 Answers

The car will turn over but won`t start but if I turn the key on and jump the starter it starts


Sounds like the ignition switch has gone kaput. The ignition switch come in two pieces, an electrical switch and a mechanical switch.

The switch electrical portion can be replaced separatly from the mechanical portion (tumbler that the key engages). It is not a real difficult repair but requires some mechanical knowlege of how the column is assembled.

This can be verified with electrical test equipment prior to buying a new electrical switch.

Apr 18, 2011 | 1994 Volkswagen Golf

1 Answer

My key won;t turn in the ignition> The wheel


Try this -
Turn the steering wheel HARD - in the same direction the wheels are pointing - have a strong person do this - while you try to turn the key WITH the foot on the brake and the car in park or neutral.
This releases the pressure on the steering column.

Please let me know if this workd
Gary
riceski@gmail.com

Jan 28, 2010 | 2002 Saturn L-Series

1 Answer

How to remove key unit from steering column 1986 F150 Ford


COUTESY OF EXPERT "C17HYDRO"
With Key
  1. Disconnect the battery ground.
  2. On tilt columns, remove the upper extension shroud by unsnapping the shroud from the retaining clip at the 9 o'clock position.
  3. Remove the trim shroud halves.
  4. Unplug the wire connector at the key warning switch.
  5. Place the shift lever in PARK and turn the key to ON.
  6. Place a 1/8 in. wire pin in the hole in the casting surrounding the lock cylinder and depress the retaining pin while pulling out on the cylinder.
  7. When installing the cylinder, turn the lock cylinder to the RUN position and depress the retaining pin, then insert the lock cylinder into its housing in the flange casting. Assure that the cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will allow the cylinder retaining pin to extend into the cylinder cast housing hole.
  8. The remainder of installation is the reverse of removal.

This section is for a NON-TILT with no key or non-functioning cylinder:
Fixed Columns
  1. Disconnect the battery ground.
  2. Remove the steering wheel.
  3. Remove the turn signal lever.
  4. Remove the column trim shrouds.
  5. Unbolt the steering column and lower it carefully.
  6. Remove the ignition switch and warning buzzer and pin the switch in the LOCK position.
  7. Remove the turn signal switch.
  8. Remove the snapring and T-bolt nuts that retain the flange casting to the column outer tube.
  9. Remove the flange casting, upper shaft bearing, lock cylinder, ignition switch actuator and the actuator rod by pulling the entire assembly over the end of the steering column shaft.
  10. Remove the lock actuator insert, the T-bolts and the automatic transmission indicator insert, or, with manual transmissions, the key release lever.
  11. Upon reassembly, the following parts must be replaced with new parts:
    • Flange
    • Lock cylinder assembly
    • Steering column lock gear
    • Steering column lock bearing
    • Steering column upper bearing retainer
    • Lock actuator assembly
  1. Assembly is a reversal of the disassembly procedure. It is best to install a new upper bearing. Check that the vehicle starts only in PARK and NEUTRAL.

This section is for TILT and no key or non-functioning cylinder:

Tilt Columns
  1. Disconnect the battery ground.
  2. Remove the steering column shrouds.
  3. Using masking tape, tape the gap between the steering wheel hub and the cover casting. Cover the entire circumference of the casting. Cover the seat and floor area with a drop-cloth.
  4. Pull out the hazard switch and tape it in a downward position.
  5. The lock cylinder retaining pin is located on the outside of the steering column cover casting adjacent to the hazard flasher button.
  6. Tilt the steering column to the full up position and prepunch the lock cylinder retaining pin with a sharp punch.
  7. Using a 1/8 in. drill bit, mounted in a right angle drive drill adapter, drill out the retaining pin, going no deeper than 1/2 in. (12.7mm).
  8. Tilt the column to the full down position. Place a chisel at the base of the ignition lock cylinder cap and using a hammer break away the cap from the lock cylinder.
  9. Using a 3/8 in. drill bit, drill down the center of the ignition lock cylinder key slot about 13/4 in. (44mm), until the lock cylinder breaks loose from the steering column cover casting.
  10. Remove the lock cylinder and the drill shavings.
  11. Remove the steering wheel.
  12. Remove the turn signal lever.
  13. Remove the turn signal switch attaching screws.
  14. Remove the key buzzer attaching screw.
  15. Remove the turn signal switch up and over the end of the column, but don't disconnect the wiring.
  16. Remove the 4 attaching screws from the cover casting and lift the casting over the end of the steering shaft, allowing the turn signal switch to pass through the casting. The removal of the casting cover will expose the upper actuator. Remove the upper actuator.
  17. Remove the drive gear, snapring and washer from the cover casting along with the upper actuator.
  18. Clean all components and replace any that appear damaged or worn.
  19. Installation is the reverse of removal. Check for proper operation.

Nov 23, 2009 | 1986 Ford F150 SuperCab

1 Answer

Install a Ignition lock cylinder 1997 Pontiac Grand Am


  • Ignition Removal Instructions
  • Disconnect the negative battery cable from the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
v\:* {behavior:url(#default#VML);} o\:* {behavior:url(#default#VML);} w\:* {behavior:url(#default#VML);} .shape {behavior:url(#default#VML);} Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Remove the upper and lower shrouds. Refer to Steering Column Trim Covers - Disassemble - Off Vehicle or Steering Column Trim Covers - Disassemble - Off Vehicle .
  • Put the key in the steering column lock cylinder set (1).

  • Turn the key to the "START" position.
  • Install a 1/16 allen wrench (2) into the hole on top of the lock module assembly in order to release the steering column lock cylinderset retaining pin.
  • Turn the steering column lock cylinder set (1) into the "RUN" position.
  • Pull the steering column lock cylinder set (1) out from the lock module assembly.
  • Remove the key from the steering column lock cylinder set (1).

19eb1ff.png


  • Installation Instructions
Normal 0 MicrosoftInternetExplorer4 st1\:*{behavior:url(#ieooui) } /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman";}
  • Insert the key into the steering column lock cylinder set (1).
  • LIne up the locking tab (2) and the positioning tab (3) of the steering column lock cylinder set with the locking tab slot (5) and the positioning tab slot (4) in the lock module assembly (6).
  • Push the steering column lock cylinder set (1) into the lock module assembly (6).
  • Rotate the steering column lock cylinder set (1) in the lock module assembly (6) into all positions.
  • Install the upper and lower shrouds. Refer to Steering Column Trim Covers - Assemble - Off Vehicle or Steering Column Trim Covers - Assemble - Off Vehicle
  • Remove the ignition key from the lock cylinder set (1).
  • Connect the negative battery cable to the battery. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical

d612a25.png

I hope this helps and good luck.
Please remember to vote 962e1fb.jpg and leave a testimonial. Thanks.

Nov 02, 2009 | 1997 Pontiac Grand Am

1 Answer

Can.t lock steering colum


is there a button on the botom of the stering column> sometimes you have a button you have to push to get the key to go to the lock position. you might take alook and see if theres a button there to release the lock

Jan 04, 2009 | 2002 Pontiac Grand Prix

Not finding what you are looking for?
2002 Chrysler Sebring Logo

Related Topics:

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...