Question about 1995 Nissan Maxima

1 Answer

How to put in a clutch

I dont know how to put in the clutch

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

It always makes good sense to mark parts before disassembling them. Clutch parts are balanced at the factory while on the engine. If the clutch cover is to be used again, it should be replaced in its original position. Make a centerpunch mark on the flywheel and on the clutch.
CAUTION
Use a HEPA vacuum to vacuum any asbestos dust from the assembly before disassembling it. Asbestos fibers can pass through a regular vacuum bag.
Use an aligning arbor to hold the disc while removing the clutch cover.
how to put in a clutch - f63-11.jpg Use an aligning arbor to hold the disc while removing the clutch cover. This will prevent it from falling accidentally. Unbolt the pressure plate bolts evenly to prevent bending the plate when the last bolt is removed. Carefully remove the assembly. Be careful not to drop the parts; they are heavy.
Inspect the clutch parts for damage. You will want to determine the cause before replacing the parts. A repeat failure must be avoided.
Use hot soapy water, brake parts cleaner, or alcohol to clean off any grease from clutch parts. Metal surfaces can be deglazed with sandpaper.
CAUTION
Do not wash clutch parts in solvent. Solvent contains oil that will be absorbed into the friction surfaces of the metal.
A clutch cover assembly is usually replaced when a disc is worn. If it is unworn, it may be reused. If you choose to reuse a clutch cover that appears to be in good condition, inspect the pressure plate to see that it is flat.
To replace the clutch assembly:

  • Install the clutch cover.
  • Install the clutch disc.
  • Attach the disc and clutch cover to the flywheel.
  • Align the punch marks on the flywheel and clutch cover if the parts are being reused.
  • Align the clutch disc.


Posted on May 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yes i have a 1992 honda accord standard, i just replace the slave and master cylinder and it dont want to go into know gear but reverse


If you put it in gear before starting engine, and then hold clutch down and try to start engine, does car try to move as if clutch is not working? If so, bleed air from clutch system. If this does not fix problem, it is always possible you got a bad replacement part.

Jun 03, 2015 | Honda Cars & Trucks

1 Answer

When I let the clutch pedal out the vehicle will


if you put on gear whit engine runnuin and release the clutch and the car dont move you need a new clutch assy

Oct 07, 2014 | Cars & Trucks

1 Answer

1993 DODGE STEALTH A/C CLUTCH NOT ENGUAGING


check play on cluch fork ecomend quarter inch play if to loose will not engage the pressure plate to clutch disc to tight always buring

Aug 25, 2012 | 1993 Dodge Stealth

1 Answer

Can the ac compressor clutch on a 2006 dodge stratus be replaced without replacing the entire ac compressor?


i dont know of any domestic cars that dont have rebuildable/replaceable clutches on the compressor. best way to find out is to call a parts store and see if you can get the part.

Mar 07, 2012 | 2006 Dodge Stratus

1 Answer

No pressure on clutch tryn to bleed and let reservoir run empty,,havnt gpt it back,,,dont know what to do?????please help


put a bar behind clutch arm on gearbox and pull it in so the slave cylinder goes in ,then open bleed valve,now assistant pumps up the clutch so the slave pushes out then put bar in the arm again and pull in back with the bleed valve open then when its in cles it and repeat operation again and it should be`perfect,if not push pedal down and jam it down with a brick and leave overnight that normally works

Aug 25, 2011 | 1991 Jeep Wrangler

1 Answer

Transmission/clutch problems


try stomping on the clutch pedal a couple of times this should help get the fluid down to the slave cylinder, I know this sounds crazy but i have had to do it on a couple of different vehicles to get it to bleed out.

Aug 29, 2009 | 1986 GMC S-15

2 Answers

Need to know what fluid to put in the clutch fluid res.


you can use dot 3 brake fluid from you local parts store, im using it in my 99 sunfire, but just ask them and they'll reommend there product.
As I see it the clutch and brakes work very similar to one another.

Aug 19, 2009 | 2005 Chevrolet Cavalier

1 Answer

Clutch goes to floor will not engage


Bleeding won't fix it,If it can be put in gear and car doesn't move your clutch is no good.

May 28, 2009 | 1994 Dodge Stealth

2 Answers

I dont know where to put the oil for the gear box


Brake fluid is the same fluid you put in the clutch master cylinder. Any mechanic will verify this.

Nov 20, 2008 | 2003 Mitsubishi Eclipse Spyder

2 Answers

Towing my boat /seems like its slipping/new clutch?


Try having clutch adjusted first, then you will know if clutch has been slipping.
Let me know if this helps. MMP

Jun 15, 2008 | 1987 Ford Bronco II

Not finding what you are looking for?
1995 Nissan Maxima Logo

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...