Question about 2000 Chevrolet Venture

1 Answer

Trying to reinstall belt tensoner on a 2000 chevy venture van with 3.4 engine has two bolt holes can not remember what goes where as far as bolt and doel pin

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 710 Answers

THERE SHOULD BE A HOLE WHERE THE DOWEL PIN GETS INSERTED. I BELIEVE THE PULLEY GOES ABOVE THE TENSIONER. HOPE THIS HELPS. GOOD LUCK. THANK YOU IN ADVANCE FOR AN HONEST RATING AND FOR USING FIX-YA. KEEP ME POSTED PLEASE

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 chevy venture won't crank with key


The pk3 system has a sensor ring around the lock cylinder these go bad a relearn will not fix this because no security code is being sent to the pass key module.

Mar 23, 2014 | 2000 Chevrolet Venture

1 Answer

How do i change a alternator for a escort van 1.8 diesel van


This is for a 1999 1.8 Diesel 55 Escort Van.

You have to remove a few parts but its not a major dilema. Almost all work needs to be carried out from under the van, so it needs jacking up.

1. Disconnect battery. Loosen bolts on FR wheel, jack up high and take wheel off. MAKE SURE HANDBRAKE IS ON AND WORKING!!!

2. Inside the wheel arch is a cover that goes over the alternator, three bolts to remove.

3. From under the van you will see a tension wheel keeping the belt tight. It requires a star shaped fitting to loosen, if you dont have one you can use a small ratchet piece that grips it.

4. Once belt is loose remove the two nuts holding the tension wheel in place. Keep to one side and remember how it goes back.

5. You now have access to the three bolts holding the alternator in place. Its tight and a little tricky but persevere and they will come out.

6. Wiggle the old unit out, unbolt the two wires on the alternator, bolt back onto the new unit.

7. Do the rest in reverse. When putting tension back on the belt do not over tighten, belt should just feel firm.

Remember to connect the battery again! And use a volt meter to test battery. You should get around 14v with engine running.

Done.

Aug 16, 2010 | Ford Escort Cars & Trucks

2 Answers

Location and placement of a water pump


ok you will see a pulley with NO GROVES with FOUR 10mm bolts
that's the water pump
remove that pulley
then there are FIVE 8mm bolts holding the water pump to front cover
remove the 5 water pump bolts
then use a screwdriver and hammer and tap the pump to seperate the pump from the cover
clean the old gasket off and reassemble
hope this helps

Dec 01, 2009 | 1997 Chevrolet Venture

1 Answer

Replacing serpentine belt on 2000 chevy van need belt diagram


My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

I am assuming this "van" is a Chevy Venture?
CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2000/make/chevrolet/model/venture/2000_chevrolet_venture_drive_belt_routing_diagram.htm

Sep 21, 2009 | 2000 Chevrolet 2500

1 Answer

Where is the air injection pump and smog pump in a 2000 Chevy Venture van?


If you look at the engine and see some tubes attatched to the exhaust manifolds ( these are called asperator tubes) follow the hose( usaualy a heavy duty rubber hose it will lead you to the pump. also you can see it from the front of the motor it is driven by the belt . ( cooling fan belt or the Harmonic ballancer belt ) .

Jul 12, 2009 | 2000 Chevrolet Venture

1 Answer

2000 Chevy Venture


wow are you serious it takes alot to loss an axle it had to be making noise for a long time and for the motor to drop all the motor mounts had to be bad did anyone work on it and forget to put the mount bolts back in your talking your looking at about $800-1000 if it just needs all the mounts and axles

Nov 01, 2008 | 2000 Chevrolet Venture

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...