Question about 1999 Ford F150 Regular Cab

1 Answer

A/c switches to heat at 2000 rpm`s

Ford f-150 1999 Air works fine until I reach 2000 rpm`s then I hear
the blend door (I think) switch over then blow heat. This only seems to
happen when I`m driving not idling.

Posted by on

  • tlw036 May 09, 2009

    thanks I`ll check the vac. lines. I`m a little confused about the

    propane I don`t think I know how to do that.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 28 Answers

Sounds like a vacuum leak i have run into that several times. however i haven't found any common place for the leak. i have found some under the dash, on the back of the intake manifold, and i have found them at vacuum resivors. i wish you luck. usually you can find leaks easily using propane. rarely i have seen a bad check valve cause this problem, but that is a possibility as well. hope i was helpful to you.. dustang

Posted on May 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford expedition no front heat, back heat work fine. I went through the glove box and into the side of the heater box, the blend door works fine. Any ideals?


if blend door works blower working check make sure you have enough coolant because suvs holds right much antifreeze.heater not working heater core plugged make sure both heater core hoses hot to touch if so problem could be temperature mode switch.

Jan 21, 2013 | 2000 Ford Expedition

1 Answer

Heat blows out air but does not get warm, any ideas?


If it is faulty, yes.
Does the temp gauge show the engine is warming up to normal temp ?
Is the radiator full of coolant ?
Are the heater hoses getting hot ?
It could also be a faulty blend door under the dash. The blend doors direct air thru the heater core and the vents.

Sep 28, 2012 | 2000 Ford Taurus

1 Answer

Heater blows luke warm air, both front pannel and rear.


do you hear a clicking sound under your dash if so the blend door accuator is bad and not switching all the way over for the heat or cold

Jan 03, 2012 | 2000 Ford Expedition

1 Answer

1997 ford explorer xlt. max ac works fine but when i switch to normal ac or change vent control it blows out heated air. How do i check or repair?


The blend door actuator is probably bad in it causing the warm air to blow out instead of cold air. It is behind the dash.

It may take several hours for a technician to get at it and replace the parts required for it to work again.

Aug 19, 2010 | 1997 Ford Explorer AWD

1 Answer

My heating system work and then blows cold air. one day it works fine and i have all the heat it need. I have to place the selector switch on recirculating air which sometimes blows heat. when the switch...


Sounds like a classic blend door problem. They will start to break and exceed the sensor's travel limit, and then the controller will stop trying to move the door. There is also a known problem when the recirc door breaks, but it is less common. For more info, google "Jeep Blend Doors". For a fix, google "Heater Treater".

Jan 07, 2010 | 2004 Jeep Grand Cherokee

1 Answer

No heat air is blowing cold


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is worm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest to flush the heater core.

Oct 22, 2009 | 1998 Ford Taurus

1 Answer

MY 1998 FOR TARUS HEATER WILL NOT WORK.WAS DRIVING


It is most probably the problem with blend door or blend door actuator. But just in case I would suggest to follow the entire procedure:

First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater not working


First you have to identify what causes the problem.
To do this you have to:
1) When engine is cold check the level of coolant. If it is low fill it up.
2) Start engine and check if engine reaches regular temperature. If your engine is not heated enough it means your thermostat does not work properly and should be replaced.
3) If engine temperature is normal, then check the temperature of pipes that go to/from heater core. These pipes are located up the fire wall (easier access is from the passenger side). If pipe/pipes are cold (even engine is warm) it means you heater core is plugged and should be flushed. Keep in mind, flushing the whole cooling system is different from flushing heater core.
4) If pipe/pipes are hot/warm, turn off the fan, switch controller to the hot position, wait for 3-4 minutes and turn on the fan. Note if the cold air blows first or warm air blows first but it cools down in 5-10 seconds. If the air blows cold than it is most probably the problem with blend door or blend door actuator.
5) If air blows warm first and then cools down, then while running engine and remaining the transmission in PARKING position, press on the gas pedal until your engine reaches 3,000 RPM. Check if your heater blows warm/hot air. If it does, then your water pump does not work properly and should be replaced. If the air still cold, I would suggest flushing the heater core.

Oct 17, 2009 | 1998 Ford Taurus

1 Answer

Heater does not work


Check blend door motor for proper operation (vacuum operated) if necessary, detach arm from heater box and move by hand. If you have heat then, change motor! You are reaching operating temp for engine, right? If not, thermostat is stuck open... Change.

Dec 22, 2008 | 1998 GMC Sonoma

Not finding what you are looking for?
1999 Ford F150 Regular Cab Logo

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75842 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...