Question about 1995 Lexus ES 300

1 Answer

LOOKING FOR PLASTIC PLUGINS FOR CONNECTOR BLOCK TO IGNITION COILS

Connector block to ignition coils. 6 coil system.changing out spark plugs and they were so brittle ,they broke.not wiring harness. primary. don't know what they are called , so i can order the parts

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Lexus Master
  • 358 Answers

You cannot get yhem with out getting the harness. will be ok the way they are. I see it all the time.

Posted on May 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a misfiring problems with cylinders 1 and 6. Which ignition coil do i need to change?


Ignition coil one and six or course.The 3.7L uses separate ignition coils for each cylinder. The one-piece coil bolts directly to the cylinder head. Rubber boots seal the secondary terminal ends of the coils to the top of all 6 spark plugs. A separate electrical connector is used for each coil.
Because of coil design, spark plug cables (secondary cables) and a distributor are not used.
Two knock sensors (one for each cylinder bank) are used to help control spark knock.
The Auto Shutdown (ASD) relay provides battery voltage to each ignition coil.
The ignition system consists of:
² 6 Spark Plugs
² 6 Separate Ignition Coils
² 2 Knock Sensors
² Powertrain Control Module (PCM

Dec 10, 2016 | Jeep Cars & Trucks

1 Answer

What controls the fire to the coil


The ignition system is controlled by the Powertrain Control Module (PCM) on all engines.
Here is a generic breakdown of most ignition systems incorporated after 1996;

The system uses separate ignition coils for each cylinder. The one-piece coil bolts directly to the cylinder head. Rubber boots seal the secondary terminal ends of the coils to the top of all 6 spark plugs. A separate electrical connector is used for each coil.
Because of coil design, spark plug cables (secondary cables) and a distributor are not used.
Two knock sensors (one for each cylinder bank) are used to help control spark knock.
The Auto Shutdown (ASD) relay provides battery voltage to each ignition coil.
The ignition system consists of:
  • Spark Plugs
  • Separate Ignition Coils
  • Knock Sensors
  • Powertrain Control Module (PCM)
  • Also to be considered part of the ignition system are certain inputs from the Crankshaft Position, Camshaft Position, Throttle Position, 2 knock and MAP Sensors

May 14, 2011 | 1997 Dodge Intrepid

1 Answer

Cylinders #4 and #6 not firing even after changing spark plugs, fuel injector, compression checkup.


The coil on plug style ignition coils have been a very weak spot in the 2002 and later MPV. Moisture can get inside and short out the internal workings. Also make sure that you have the correct electrical connectors plugged into the correct ignition coil. It is possible to accidently swap the connectors for #4 and #6 ignition coils and the harness still looks like it is routed correctly.

May 01, 2011 | 2002 Mazda MPV

1 Answer

How to change spark plugs on 5.4l


Your van uses a coil on plug ignition system. Use the following procedure to change the plugs.

  1. Remove the engine cover and air cleaner assembly.
  2. Disconnect the ignition coil electrical connector.
  3. Remove the ignition coil mounting bolt.
  4. Remove the ignition coil.
  5. Remove the spark plug.


tecnovative_21.gif

Jan 13, 2011 | 1999 Ford Econoline

1 Answer

How to change the spark plugs on peugeot 406 v6 3l coupe is this straight forward like a 4 cylinder car


1. Spark plugs removal

1.1. Front cylinder bank spark plugs removal:
1.1.1. Disconnect the battery from car terminals.
1.1.2. Remove the engine plastic cover.
1.1.3. Disconnect the ignition coils electrical supply cable and all three coils connectors.
1.1.4. Remove all three ignition coils screws.
1.1.5. Remove all three ignition coils out from cylinder head.
1.1.6. Remove all three spark plugs out from cylinder head (straight forward).

1.2. Back cylinder head bank spark plugs removal:
1.2.1. Remove the inlet manifold out from cylinder head.
1.2.2. Disconnect all three ignition coils connectors.
1.2.3. Remove all three ignition coils screws.
1.2.4. Remove all three ignition coils out from cylinder head.
1.2.5. Remove all three spark plugs out from cylinder head (straight forward).

2. Spark plugs installation

2.1. Refit all in reverse order.
2.2. Spark plugs tightening torque = 2,8 +/- 0,3 daN.m
2.3. Ignition coils tightening torque = 0,8 +/- 0,2 daN.m

Nov 16, 2010 | 2005 Peugeot 405

1 Answer

Changed fuel pump. getting fuel to engine. but will not start.


Check for spark. Maybe a crankshaft position sensor is bad or a module.

Secondary Spark Test This spark tester looks just like a spark plug, attach the clip to ground and crank the engine to check for spark 91052p10.jpg
This spark tester has an adjustable air-gap for measuring spark strength and testing different voltage ignition systems 91052p11.jpg
Attach the clip to ground and crank the engine to check for spark 91052p12.jpg
This spark tester is the easiest to use just place it on a plug wire and the spark voltage is detected and the bulb on the top will flash with each pulse 91052p10.jpg
The best way to perform this procedure is to use a spark tester (available at most automotive parts stores). Three types of spark testers are commonly available. The Neon Bulb type is connected to the spark plug wire and flashes with each ignition pulse. The Air Gap type must be adjusted to the individual spark plug gap specified for the engine. The last type of spark plug tester looks like a spark plug with a grounding clip on the side, but there is no side electrode for the spark to jump to. The last two types of testers allows the user to not only detect the presence of spark, but also the intensity (orange/yellow is weak, blue is strong).
  1. Disconnect a spark plug wire at the spark plug end.
  2. Connect the plug wire to the spark tester and ground the tester to an appropriate location on the engine.
  3. Crank the engine and check for spark at the tester.
  4. If spark exists at the tester, the ignition system is functioning properly.
  5. If spark does not exist at the spark plug wire, perform diagnosis of the ignition system using individual component diagnosis procedures.
---
Ignition Coil Testing
  1. Remove suspect coil.
  2. Disable fuel pump by disconnecting inertia switch electrical connector.
  3. Reconnect the ignition coil electrical connector to the coil.
  4. Install spark tester 303-D307 (D81P-6666-A) or the equivalent.
  5. Crank engine while observing the tester.
  6. If a blue-white spark is not observed replace coil.
---
Removal & Installation To Remove:
  1. Remove the air cleaner outlet pipe if interfering.
  2. Disconnect the connector from the ignition coil. coilconn.gif

  3. Remove the bolt from the ignition coil. coilbolt.gif

  4. Remove the ignition coil on plug.
To Install:
  1. Install ignition coil on spark plug.
  2. Install ignition coil bolt. Tighten to 10 Nm (89 in. lbs.). coilbolt.gif

  3. Reconnect the ignition coil electrical connector. coilbolt.gif

  4. Install the air cleaner outlet pipe if removed earlier.
prev.gif next.gif

Oct 28, 2010 | 1999 Ford Crown Victoria

1 Answer

There is a misfire in my engine, changed plugs & wires. now it reads that the fuel leveling sensor is bad, will this help?


If there is a misfire, the cylinder that it is misfiring in will be recorded as a code in the computer.

Have the car scanned to determine which cylinder is bad. Then, replace the coil pack going to that cylinder.

Ignition Coil Pack Removal & Installation 2V Engine To Remove:
  1. Twist the spark plug wires off of the ignition coil towers. Mark the spark plug wire positions so they can be installed in their original positions.
  2. Disconnect the electrical connector from the ignition coil. CAUTION
    When removing the spark plug wires, a slight twisting motion will break the seal and ease removal.
    coilconn.gif

  3. Remove the mounting screws and remove the ignition coil.
To Install:
  1. Position the ignition coil pack on engine.
  2. Install mounting screws and torque to 53 in-lbs. (6 Nm). coilbolt.gif

  3. Connect ignition coil pack electrical connector.
  4. Match previously marked spark plug wires to ignition coil and install.
4V Engine To Remove:
  1. Remove the RH cowl grille cowlpic.gif
  2. Remove the screws and the water shield
  3. Mark spark plug wire positions
  4. Disconnect the spark plug wires from the ignition coil CAUTION
    When removing the spark plug wires a slight twisting motion will break the seal and ease removal.
  5. Disconnect the ignition coil electrical connector coilconn.gif

  6. Remove the mounting screws and remove the ignition coil
To Install:
  1. Position ignition coil pack. Install mounting screws and torque to 56 in-lbs. (6Nm)
    coilbolt.gif

  2. Connect ignition coil pack electrical connector
  3. Match previously marked spark plug wires to ignition coil and install
  4. Position water shield and install screws
  5. Install RH cowl panel
prev.gif next.gif

Aug 11, 2010 | 2002 Ford Taurus

1 Answer

Where can I find the Ignition Coil in a 2006 Ford Taurus?


Ignition Coil adobe.gif Printable View (79 KB) Removal and Installation
  1. ani_caut.gif CAUTION: It is important to twist the spark plug wire boots while pulling upward to avoid possible damage to the spark plug wire.
    ani_caut.gif CAUTION: Spark plug wires must be connected to the correct ignition coil terminal.
    Disconnect the 6 spark plug wires from the ignition coil by twisting while pulling upward.
  1. Disconnect the ignition coil electrical connector.
  1. Remove the 3 bolts and the ignition coil.
    • To install, tighten to 6 Nm (53 lb-in).
  1. To install, reverse the removal procedure.
fbf58a7.jpg

Hope this helps.. Cobra

Jun 12, 2010 | 2006 Ford Taurus

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Change spark plugs


My 2004 Verona had factory installed "NGK BKUR6ETB" regular spark plugs which I replaced at 30,000 miles. The 2005 model year is supposed to have Iridium spark plugs. To replace the spark plugs: 1. Remove plastic top engine cover. 5 nuts 10mm socket. 2. Unplug connector from each ignition coil. qty 6. 3. remove 2 hold down bolts per ignition coil. 10mm socket. 4. remove ignition coil, lifting straight up. 5. Spark plug is now accessible, use deep well 5/8 spark plug socket to remove.

May 15, 2008 | 2004 Suzuki Verona

Not finding what you are looking for?
1995 Lexus ES 300 Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...