Question about Chrysler Sebring

Open Question

Failed NJ inspection codes 442 & 455

I have an '02 Chrysler Sebring tha failed NJ inspection codes 442 & 455? How can this be fixed?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 155 Answers

SOURCE: Codes PO 442, 449 and 455

Check all vacuum lines from the gas tank to the evaporative charcoal cannister by the gas tank and to the purge valve located at the engine. Check the electrical connector at the vent solenoid which should be located on the charcoal cannister and purge valve solenoid by the intake manifold.

Posted on Jun 10, 2009

motor1258
  • 6674 Answers

SOURCE: OBD codes 442 & 455

Check all of your EVAP lines and the charcoal canister. Also check the lines and overflow line from the gas cap to the gas tank.

Posted on Jun 12, 2009

Molson02536
  • 3854 Answers

SOURCE: Engine codes for 2001 Chrysler Sebring P0442 455 and 1685

PO442 means you have a small leak in your EVAP system. Most common cause is a bad gas cap, replace the gas cap with a factory gas cap,after market fail or does not conform to the OEM EVAP system. Other cause would be small leaks in the EVAP vacuum lines. P0445 is also related to the EVAP system and has detected a large leak in the system. Start with the gas cap as mentioned above. P1685 Is an issue with the ignition not recognizing the ignition keys and the car's ignition immobilizer my activate leaving the car not being able to start. That's going to have to be a Dealer repair. Good luck and hope this helps.

Posted on Jun 15, 2009

  • 31 Answers

SOURCE: code 442 cleared it now code 455 whats up

there is a leak within the evap solenoid and lines.find the leak with a smoke tester.

Posted on Oct 04, 2009

  • 96 Answers

SOURCE: where is bank 1 02 sensor on a 2002 chrysler

its the on cylinder 1 manifold. closest 2 the passenger side firewall rite bhind the cubbyhole

Posted on Feb 13, 2010

Testimonial: "Thank You"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The easiest way to take off a water pump for 2004 Chrysler Sebring


Take it to a garage and say "put a new water pump in this for me".

2004 Chrysler Sebring 2.7Ltr. Water Pump Replacement ...

z? 29:29 https://www.youtube.com/watch?v=ebeXcNmBnnE Sep 19, 2015 - Uploaded by Paul Veltum In this video I'll walk you through replacing the water pump on this 2004 Chrysler Sebring with it's 2.7 ...

2004 Chrysler Sebring Timing Belt Water Pump Before 90K ...

2q==? 13:03 https://www.youtube.com/watch?v=UQHRa28sRkY Nov 25, 2012 - Uploaded by Mastermind Denver This video shows why we at Mastermind Enterprises Auto Repair Shop in Denver recommend replacing the ...

WATER PUMP REPLACEMENT IN CHRYSLER 2.7L ...

9k=? 4:52 https://www.youtube.com/watch?v=z_QrXR2jcb8 Mar 7, 2014 - Uploaded by kzguy2 2008 Dodge Charger 2.7l was in need of a new water pump due to it leaking. ... 2004 Chrysler Sebring 2 ...

2004 chrysler sebring water pump weep hole inspection ...

2q==? 0:15 https://www.youtube.com/watch?v=wzqHaQ40doQ Feb 26, 2014 - Uploaded by Graeme Tolton 2004 chrysler sebring water pump weep hole inspection with borescope. ... 2004 Chrysler Sebring 2.7Ltr ...

Chrysler 2.7L Water Pump Installation Problems - YouTube

9k=? 3:30 https://www.youtube.com/watch?v=h5_VFJ1gCpI Nov 19, 2014 - Uploaded by South Main Auto Repair When I installed this water pump on the 2006 Chrysler Sebring 2.7L I ran into a ... 2004 Chrysler Sebring 2 ...




Feb 15, 2016 | Chrysler Cars & Trucks

2 Answers

Chrysler sebring code p0601


Hi Again,here's another link,to your P0601 code. P0601 OBD II Trouble Code

Jan 31, 2015 | 2002 Chrysler Sebring

2 Answers

2004 Sebring failed the emissions testing


Probably not a cheap fix.
The car will not pass the test if the light is on during the test.
The light is on when the computer has a problem that will affect emissions or performance.
You would need to have the computer scanned for trouble codes then fix the problem. Once the problem is fixed and the code is erased, the light should stay off.

Mar 03, 2013 | 2004 Chrysler Sebring Convertible

1 Answer

2001 sebring failed nj inspection - obd code p0601 - how to fix?


A code P0601 in most cases means the PCM has gone bad. This is possibly due to a short-circuit inside the PCM. Or, if you disconnect the wires/connector from the PCM while the battery is still connected, that may also cause this code.
Possible Solutions

With a P0601 OBD-II trouble code, the most common fix is to replace and reprogram the PCM. In a few cases the dealer may be able to reflash the PCM and get it working. But more than likely the PCM will need to be replaced and reprogrammed (we recommend you take it to a dealership for this). The good news is it *may* be covered under your emmissions warranty. So even if you're out of bumper-to-bumper warranty or powertrain warranty, check your warranty guide or dealer to see if this is covered.

Other people have reported that they cleared the code only for it to return again and again. Keep in mind that most shops can replace the PCM but not all can program it.

Hope thie helps.

Sep 06, 2011 | 2001 Chrysler Sebring

1 Answer

I failed my inspection the guy said it was an emissions problem the code was po442


EVAP System ---PO 442 (small leak)

I'm going to guess, that will mean nothing to you

You need to have the vehicles EVAP System checked
out by a repair shop, that does know something,of your
lucky & get the right place.

Aug 01, 2011 | Chevrolet Malibu Cars & Trucks

2 Answers

I have fault codes P1684 & P0340 on my 2002


P1684 The battery has been disconnected within the last 50 starts.

P0340


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM. Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it.
Symptoms Symptoms can include:
  • Hard starting or no start
  • Rough running / misfiring
  • Loss of engine power
Causes A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • the crankshaft position sensor may have failed
Possible Solutions With a P0340 OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required

May 30, 2011 | 2002 Chrysler Sebring

1 Answer

I have a 2001 chrysler sebring convertable with an air bag light that is on and it does not have any code numbers but it says no srim message


issue with your Computer Dash Board Dealling With a Air Bag could Be very dangerous I suggest to send Your Car to a Chrysler Dealler Garage for inspection

Sep 22, 2010 | 2004 Chrysler Sebring

1 Answer

My CHRYSLER SEBRING SHIFT KNOB DON'T MOVE FROM PARK IN TO GEAR


Thats quite common on 2007-2008 models. You should have received a letter from Chrysler Corp. addressing this issue. (I did). The y said to take it to your nearest Chrysler dealer and they will fix it free (parts & labor). They will install a clip to reinforce the mechanism that assist this button to release it from park. Mine has not failed yet on my 2008, but it did on my son-in-laws 2007 (after his warranty expired) But he never recieved a letter. Your car might have to still be under warranty...........Good luck.

Aug 19, 2010 | 2007 Chrysler Sebring Sedan

1 Answer

Rear view mirror for 98 chrysler sebring


Hello Glitterqueen,

I have had the honor of perusing some of the finest
AUTOMOTIVE SWAP MEETS in the nation...
Northern California, Carlisle & several years of Hershey
being the best memories...!!

Before that we amateurs had the option of NEW
DEALER parts... usually abusively expensive
or "junking" (looking through SALVAGE YARDS)...

THE INTERNET... specifically eBay has brought
a whole new world to my finger-tips...
Have a look at the pages below...

Surprising prices on ROCKAUTO ... (in my opinion)
but do know your prices before trying AMAZON,
especially watchful of your shipping methods & COSTS.

NEW FACTORY OEM CHYSLER SEBRING AUTO DIM REAR VIEW MIRROR COMPASS...

http://www.ebay.com/sch/i.html?_from=R40&_trksid=p2050601.m570.l1313.TR0.TRC0.H0.X1998+chrysler+sebring+rearview.TRS0&_nkw=1998+chrysler+sebring+rearview&_sacat=0

Carnac the Magnificent

Apr 01, 2017 | 2000 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...