Question about 2000 Dodge Ram 3500

1 Answer

I need to change the in tank fule pump in my truck its a dodge ram 3500 v10 how do you do it ryan

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

The tank has 2 straps that hold the tank to the frame(make sure tank is some what empty, the emptier the lighter) then just disconnect the fuel lines and wires then you can to the pain in the **** ring (some times the ring is loose enough to turn with a hammer and chisel) the book says make a "special tool" but you can be creative. then remove the fuel pump canister and follow the directions depending on if you bought the whole Mopar replacement canister or just a replacement fuel pump.
Hope this helps

Posted on Feb 07, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring in a transfer tank pump in 2011 dodge 3500


Will you have 2 separate tanks, You will need to run the fuel line safely up against the frame to where you want to mount it and add the new pump. You will need a valve that shuts off one tank then the other as you need it. I'm sure you can find one with the info in the box. Use your original pump to feed the motor.That is if it's a puller pump. You tube might make it simpler? Get ahold of me and
i'll walk you thru it!

Jan 28, 2013 | 2011 Dodge Ram Pickup 3500

1 Answer

2000 ram 3500 deisel dies at 2000 rpm won't start


could be fuel elated, there are two fuel pumps, the high pressure pump to feed the injector system and the lift pump to get fuel from tank to the high pressure pump. Check fuel filter also and start there. The fuel pumps are expensive. What have you checked so far and eliminated?

Feb 23, 2012 | 2000 Dodge Ram 3500

1 Answer

2004 dodge ram 3500 died in parking lot and will not start turns over and has fuil but will not start


Could be the lift pump, common problem on the 2004. There is a fix for it called an in tank lift pump conversion. Ask your dealer or check online.

May 20, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

2004 dodge p0628 code does not start


those year trucks have bad lift pumps on the diesel engine. it is located near the fuel filter. they are also known for starving the injecter pump for lubrication oil due to the pumps low capacity. it is now recomended that an in the tank pump change over kit be installed

Mar 23, 2010 | 2004 Dodge Ram 3500 Truck

2 Answers

Where is fuel filter in 1999 dodge ram


1999 Dodge Truck RAM 1500 1/2 ton 4WD 5.9L SFI 8cyl
The Fuel Filter is located: Under vehicle, center, below cargo area, mounted on top of fuel tank, in fuel pump module

For other RAM models or engine sizes, I suggest visit autozone.com (free register).

Good luck (remember rated this post).

Mar 01, 2010 | 1999 Dodge Ram

1 Answer

I have a 2004 Doge Ram 3500 cumming run 5mile Dies and restart and repets about the same miles I tride pump test and its to spec


get fuel pressure gauge ASAP. replace lift pump with after market one (not in tank from dodge..junk)

Feb 03, 2010 | 2004 Dodge Ram 3500 Truck

1 Answer

Where can i find a engine diagram of a dodge 1999 3500 van


Do need you to know where the sensor is located ? If so it's located inside distributor housing, just below rotor on (3.9L-V6 5.2L-V8 5.9-V8) 8.0L-V10 cam sensor is located on the timing chain cover.

Jul 01, 2009 | 1998 Dodge Ram 3500 2WD

1 Answer

I have a 2000 dodge ram 3500 l6 turbo diesel, just had the fuel pump and injectors replaced, but now no fuel is passing along, and can not hear the pump turn on. replaced the fuel system relay and still...


pump is your only choice at this point...HOWEVER, it does have sufficient fuel in the tank and switched to the supply tank (in case you have dual tanks) right?

Jun 22, 2009 | 2000 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...