Question about 1990 Ford F250

1 Answer

90 F250 7.5L e4od what is the trade secrit for removing the bell housing bolts exply the top two

Posted by on

  • yadayada
    yadayada May 11, 2010

    You have to drop the back of th engine down as low as you can, then u can reach them.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

Swivels and extentions

Posted on Sep 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bolts out of 2003 for removal of transmission


If you are talking about the two bolts on top of the bell housing. You will need a three foot extension with a swivel and 15 mm socket. To access the top bolts you need to put your jack with a piece of wood under the transmission pan, jack it up just enough so you can remove the rear cross member then slowly lower your jack supporting the trans. Until you see those top bolts approx. Three inches assuming you have removed all the other bolts on bell housing and the three bolts that attach the flywheel to the pumpkin.

Apr 25, 2014 | 2004 Chevrolet TrailBlazer

1 Answer

Where are the bolts located that mount the starter on a 1995 audi 90


some go thru the trans bell housing into the starter nose and by all means they will be metric..also some models have a torque bar attatched to the back of it especial;ly diesel engines..

Feb 24, 2013 | Cars & Trucks

1 Answer

A cannot get the top center bolt out of the bell housing into the engine block on my 4l60e transmission in my 2001 chevy silverado 4x4


to remove the upper bell housing center bolts on a 4L60E (not an E if it's 4wd by the way but we'll go with that for now)
you will have to unbolt the transmission from the crossmember and drop it down which will in turn tilt your motor back and allow you better access to those two top bolts. Put your two bottom bolts back in finger tight before you drop the transmission down though or you stand the chance of breaking the bell housing when it's tilted back. you can also use a floor jack on your crank pulley on the front of the motor. Jack up on it and the motor will tip back but not if you have the transmission bolted in place still. hope this helps

Feb 22, 2013 | Cars & Trucks

1 Answer

How do i remove a dip stick housing?


If it's an oil dip stick tube and it presses into the bottom of the engine block. There should be a mount on the tube with a bolt whole that bolts to the block. If it is a Transmission Tube for automatic the same thing but bolts to the bell housing bolt top left of bell housing. Good Luck. Have a great day. Eddy the Master Mechanic.

Mar 09, 2012 | 1999 Dodge Ram

1 Answer

Transmission removel


FRONT WHEEL DRIVE, OR REAR WHEEL DRIVE? REAR WHEEL DRIVE: REMOVE THE DRIVE SHAFT, AND STARTER! UNHOOK BATTERY FIRST! CARRAMPS WILL BE HELPFUL! LOOSEN ALL BOLTS AROUND THE BELL HOUSING TO THE BACK OF THE MOTOR, AS WELL AS THE TWO CROSSMEMBER BOLTS AT THE BACK OF THE TRANSMISSION! TAKE ALL THE BOLTS OFF THE TOP AND BOTTOM OF THE BELL HOUSING LEAVING TWO SIDE BOLTS IN UNTIL YOU GET A HELPING HAND, OR A FLOOR JACK TO HELP SUPPORT IT! REMOVE THE LAST TWO BOLTS, AND WIGGLE THE TRANSMISSION LOOSE! CONTINUE BACKWARDS WITH THE TRANSMISSION UNTIL IT CLEARS THE FLYWHEEL, AND LOWER IT TO THE GROUND!

Feb 26, 2011 | 1999 Buick Regal

1 Answer

Trying to change a stater cant find the bolts on top


the top bolts come in from the rear of the bell housing. They these bolts mount both the bell housing to the block and the starter motor to the block. Under neath just line up wich mount bolts are close to the starter and undo them, possibly 2 that hold them. once remove starter should fall straight into your hand

Jan 22, 2011 | 1997 Ford Expedition

1 Answer

How do i connect my starter to the battery


REMOVAL & INSTALLATION 2.2L (VIN 4) Engine Fig. 1: Removal and installation of the starter — 2.2L engine shown 87952039.gif
Fig. 2: Remove the starter electrical connections from the back of the starter 91142p05.jpg
Fig. 3: Remove the three bell-housing cover retaining bolts and . . . 91142p06.jpg
Fig. 4: . . . remove the bell-housing cover 91142p07.jpg
Fig. 5: Remove the starter support brace-to-engine bolt 91142p08.jpg
Fig. 6: The starter is retained by two bolts 91142p09.jpg
Fig. 7: Remove the bolts and . . . 91142p10.jpg
Fig. 8: . . . remove the starter from the engine 91142p11.jpg
Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside 91142p12.jpg
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter. To install:
  8. Transfer the starter support bracket to the new starter if the starter is being replaced.
  9. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  10. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  11. Install the bell-housing cover.
  12. Install the starter electrical connections on the back of the starter. Tighten the "S'' terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  13. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines 87952040.gif
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable access to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle. To install:
  9. Raise the starter to the vehicle, then attach the wiring.
  10. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  11. If moved, reposition the engine wiring harness.
  12. Carefully lower the vehicle.
  13. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  14. Fasten the air inlet duct to the throttle body.
  15. Connect the negative battery cable.
prev.gif next.gif

Aug 19, 2010 | 1996 Chevrolet Cavalier

1 Answer

How do i replace the crank position sensor on a 2000 jeep grand cherokee


If you have the type of crank angle sensor shown in the image, then it will be located on the bell-housing towards the top of the bell-housing and usually on the drivers side. Dis-connect the faulty crank angle sensor and then un-bolt the two bolts that secure the crank angle sensor to the bell-housing and then remove the sensor. The best access to the crank angle sensor is from under the vehicle.


47ada7e.jpg

Jun 21, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Steps required to remove the standard transmission from a 1992 Toyota pickup. Bell housing bolts, starter, and rear trans. support have been removed, but the trans/bell housing will not separate from from...


Make sure you have removed all the bolts ....you will have to pry hard to remove it out .....be careful not to crack the bell housing ..Pry around the bell housing .good luck

Jan 02, 2010 | 1992 Toyota Pickup

2 Answers

Where is the starter on a 1998 cavalier z24


1998 Chevrolet Cavalier 2.4L SFI DOHC 4cyl - Repair Guide
Look at the the lower end of the engine behind the radiator.

REMOVAL & INSTALLATION

2.2L (VIN 4) Engine

b30d4a5.jpg

Fig. 1: Removal and installation of the starter-2.2L engine shown

ce77b94.jpg

Fig. 2: Remove the starter electrical connections from the back of the starter

a7d8ae8.jpg

Fig. 3: Remove the three bell-housing cover retaining bolts and ...

3580a66.jpg

Fig. 4: ... remove the bell-housing cover

95f5421.jpg

Fig. 5: Remove the starter support brace-to-engine bolt

225716e.jpg

Fig. 6: The starter is retained by two bolts

51b21e5.jpg

Fig. 7: Remove the bolts and ...

35a623c.jpg

Fig. 8: ... remove the starter from the engine

3658d11.jpg

Fig. 9: Note that the starter bolts are two different lengths, the longer one goes on the inside
  1. Disconnect the negative battery cable at the battery.
  2. Raise and safely support the vehicle.
  3. Remove the electrical connections from the back of the starter.
  4. Remove the bell-housing cover.
  5. Remove the starter support bracket bolt from the engine block.
  6. Unfasten the starter motor-to-engine bolts, then carefully lower the starter.
  7. Remove the nuts/bolts that hold the starter support bracket to the starter.
To install:
  1. Transfer the starter support bracket to the new starter if the starter is being replaced.
  2. Raise the starter into position and secure the starter using the starter motor-to-engine bolts. Tighten the bolts to 32 ft. lbs. (43 Nm).
  3. Install the starter support bracket-to-engine bolt to 24 ft. lbs. (32 Nm).
  4. Install the bell-housing cover.
  5. Install the starter electrical connections on the back of the starter. Tighten the S terminal to 22 inch lbs. (2.5 Nm) and the battery terminal to 106 inch lbs. (12 Nm).
  6. Carefully lower the vehicle, then connect the negative battery cable.
2.3L (VIN D) and 2.4L (VIN T) Engines

7ac0166.jpg

Fig. 10: When installing the starter, tighten the mounting bolts to 66 ft. lbs. (90 Nm) on the 2.3L and 2.4L engines
  1. Disconnect the negative battery cable at the battery.
  2. Detach the air inlet duct from the throttle body.
  3. Remove the top starter bolt.
  4. Raise and safely support the vehicle.
  5. Remove the lower starter retaining bolt.
  6. If necessary, position the engine wiring harness aside.
  7. Position the starter to enable accese to the solenoid wiring, then detach the wiring.
  8. Remove the starter from the vehicle.
To install:
  1. Raise the starter to the vehicle, then attach the wiring.
  2. Position the starter, then secure using the lower starter bolt. Tighten to 66 ft. lbs. (90 Nm)
  3. If moved, reposition the engine wiring harness.
  4. Carefully lower the vehicle.
  5. Install the top starter bolt, then tighten to 66 ft. lbs. (90 Nm).
  6. Fasten the air inlet duct to the throttle body.
  7. Connect the negative battery cable.

I hope help you with this (remember rated this help) Good luck.

Oct 12, 2009 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
1990 Ford F250 Logo

Related Topics:

127 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...