Question about Nissan Pulsar

Open Question

2002 nissan micra head bolts torque specs - Pulsar Nissan Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

Ad
polarcycle
  • 1392 Answers

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Posted on Aug 16, 2009

outdoorsman5
  • 631 Answers

SOURCE: head bolt torque specs for 2000 dodge neon 2.0 SOHC

I have the specs and diagrams. If you want me to send them to you, give me your email address. Outdoorsman592003@yahoo.com

Posted on Sep 05, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1861 Answers

SOURCE: need torque specs for a 2002 toyota camry 2.4 for

The 2002 2.4 engine head bolts are 'torqued to distance'.

First, install all the bolts, and, in a sequential fashion, starting at the innermost, working outward, torque all bolts to 70 N-m/806 kgf-cm/58 foot lbs.

Next, mark the front side of each head bolt with a dot of paint. Retighten te cylinder head bolts 90 degrees, starting at the inner 2, and working outward.

We hope that this helps you out.

Posted on Dec 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque specs for the heads on a 2000 Nissan Xterra 3.3 l


AutoZone has a lot of info on torque specs for various vehicles.
The Xterra uses torque to yield bolts which must be replaced every time the bolt is removed.
Here's the site -
https://www.autozone.com/repairguides/Nissan-Frontier-Xterra-1998-05/Engine-Mechanical-Components/Cylinder-Head/_/P-0996b43f8037f9d4

Jan 09, 2018 | Nissan Cars & Trucks

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

1 Answer

2004 nissan frontier head torque specs


You should have torque to yield bolts there. That means single use - you need to buy new bolts. Then, you would torque to spec (maybe 10-12 ft. lbs.) then an additional 65 degrees of tightening rotation.
Call your local auto parts supplier.
Repair Guides Specifications Torque Specifications AutoZone com

Feb 26, 2015 | Nissan Frontier Cars & Trucks

1 Answer

2002nissan3.5cylinderheadtorque



2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:

  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Apr 12, 2012 | Cars & Trucks

2 Answers

2002 nissan maxima 3.5 cylinder head torque


Hi there:

2_17_2012_6_58_18_pm.jpg

Fig. Cylinder head bolt loosening sequence - Altima & Maxima 3.5L engine

Install the cylinder head bolts and torque in sequence as follows:
  1. Step 1: 72 ft. lbs. (98 Nm).
  2. Step 2: Completely loosen all bolts.
  3. Step 3: 26-32 ft. lbs. (34-44 Nm).
  4. Step 4: plus 90-95 degrees clockwise.
  5. Step 5: plus 90-95 degrees clockwise.

2_17_2012_6_59_54_pm.jpg

Fig. Right cylinder head bolt torque sequence- Altima & Maxima 3.5L engine


2_17_2012_7_00_21_pm.jpg

Fig. Left cylinder head bolt torque sequence- Altima & Maxima 3.5L engine

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Feb 17, 2012 | Nissan Cars & Trucks

1 Answer

Replacement of a head gasket on 2.5 liter nissan altima 2002


frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Mar 10, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...