Question about Cars & Trucks

Open Question

Toyota camry 200 si 1998 model torque settings

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: 1998 toyota camry interior dome light replacement

Look closely at the cover. You will see a small slot. Insert a small flat blade screwdriver, and pry it off. Very easy..

Posted on Nov 10, 2008

  • 92 Answers

SOURCE: torque specs for 1998 tercel 1.5L

Main Bearing Cap Torque-42 Ft. Lbs.
Head Bolts Step 1-33 Ft. Lbs. Step 2- Additional 90 Degrees
Rod Bearing Nuts-29 Ft. Lbs.

Hope this helps

Posted on Sep 20, 2009

  • 318 Answers

SOURCE: 1998 toyota camry , 2 codes, p0171. + p1133

P0171 lean code. Clean the maf sensor. A f sensor is inthe exhaust pipe.

Posted on Oct 27, 2009

  • 3433 Answers

SOURCE: 1998 toyota camry le 4 cylinder How do you set the

Just make sure the timing belt is on properlyy, lining up the cam and crank in proper position to each other. The engine willstart when fully assembled because the electrical has not be altered. If it has a crank position sensor , be sure to put it back on after cleaning it and the connector.

Posted on Nov 14, 2009

  • 496 Answers

SOURCE: I need the torque settings

cylinder head bolts:

step one: 22 Ft-lbs.
step two: tighten additional 90 degrees
step three: tighten additional 90 degrees

Posted on Feb 22, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

3 Answers

Hi, what is the cylinder head, conrod and main bearing torque settings for a toyota camry 2L,1996 model.

-Always follow its repair manual. Never trash any body.
-Good mechanic always did. doesn't matter how many car he or she repair or same model.

Good Luck


Jun 03, 2015 | 1996 Toyota Camry

1 Answer

How many huors power did toyota camry 1998 grand had ?

The 1998 Camry 2.2L engine has 133 horse power, and produce 147 (lb/ft) torque @ 4400 RPM.

Aug 12, 2014 | 1998 Toyota Camry

1 Answer

Motor se apaga cuando lo hacelero o y despues como que si se ahoga toyota camry 1998

google translator
Motor shuts off when hacelero oy then as if toyota camry 1998 drowning
ok , the engine stalls. by flooding, (gross excess fuel)
ever do a tune up, do the 60k, mile critical service points.

Dec 13, 2013 | 1998 Toyota Camry

1 Answer

How do u remove auto trans from Toyota camry sdv10r

Have ya removed the bolts holding torque converter normally have to remove one by onehole in bell housing

Oct 18, 2012 | 1998 Toyota Camry

1 Answer

What does it take to replace a rear right lateral arm on a 1998 toyota camry

I have read of some fasteners in this area being corroded on, Mine look alright, and I'd certainly give it a go. Here is information for an earlier model which may assist, p89

Mar 08, 2012 | 1998 Toyota Camry

1 Answer

Transmission fluid capacity for 1998 Toyota Camry

According with the repair guide, with automatic transmission...Transmission model A541E (17 bolt fluid pan): - Service change only - 3.7 quarts.
- Total refill - 8.5 quarts.
Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 01, 2012 | 1998 Toyota Camry

1 Answer

Cost of replacing a 1998 Toyota Camry brake booster

Labor-6hr Labour
Disconnect piping Flares nut
Drain Brake Fluid
Disconnect brake pedal assembly
Remove Brake Boost (4 nuts behind the Instrument panel)
Remove Brake Booster.

Jun 09, 2010 | 1998 Toyota Camry

1 Answer

I have a 1998 camry and after an oil change my check engine light came on. What could be the problem?

on your model (after 1996) the check engine light can come on for over 200 reasons, so the only sane thing to do is have the system tested for the trouble that is stored in the memory of the cars computer to see what is causing the problem.

Aug 13, 2009 | 1998 Toyota Camry

1 Answer

Torque settings for big ends on a 97 toyota camry 220sei

On the V-6 it's 25 Nm (18 ft lbs) on the first pull and then you rotate the next pull 90 degrees using a torque angle wrench.

Checking the specifications for the four cylinder:
25 Nm (18 ft lbs) on first pull and 90 degrees
on the second pull using a torque angle wrench.

May 01, 2009 | 1990 Toyota Corolla

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides