Question about Cars & Trucks

1 Answer

Will not go into gear

1991 corvette, will not go into gear after change master and slave cylinder

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,494 Answers

You may have to bleed the slave cylinder to get it to work. Bleed it just like brakes-pedal going to floor, open valve. Close valve, pump pedal and pedal to floor again with bleed valve open. When fluid comes out in steady stream with pedal pressed, done. Watch the plunger on the slave cylinder when clutch is pressed-it should move out to move the clutch lever.

Posted on Nov 29, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Hydraulic clutch problems

i have a ktm 125 wich all ktms have hydraulic cluthcs and i have the same problem as all these fellas even when im riding it just sucks right down all the fluid reply to me on X-KTMrida-X@hotmail.com ok thanks fellas

Posted on Oct 27, 2008

emissionwiz
  • 79865 Answers

SOURCE: Can't bleed master and slave clutch cylinders on

U will need a special tool called a pressure bleeder and a source of pressurized air..

Posted on Mar 10, 2009

  • 1 Answer

SOURCE: 1985 TOY 4X4 PICK UP HARD TO GET INTO FIRST GEAR

May be a syncro ring going out. A tranney shop can rebuild the trans and change out the syncros or if you are good with mechanics you can get a book for your tranny and do it yourself. Most manual tranneys are not too hard to do.

Posted on Mar 23, 2009

  • 14036 Answers

SOURCE: 2001 Ford ranger edge. The gears won't change.

CLUTCH SLAVE CYLINDER IS IN THE TRANSMISSION GOING TO PRESSURE PLATE AND CLUTCH.YOU HAVE TO DROP TRANSMISSION TO GET TO SLAVE CYLINDER.IF CLUTCH IS LOOSE MAKE SURE BOLTS TO CLUTCH PRESSURE PLATE TO CLUTCH IS TIGHT.THAT COULD BE YOUR PROBLEM.

Posted on Nov 06, 2009

  • 70 Answers

SOURCE: On 1991 stealth r/t 5 speed manual , yesterday

ok starting where you did... on the side of the transmission itself there will be a 1/2 inch socketed plug that can be undone to add gear oil there will be another on the bottom that can be used to drain the oil. for clutch master, standard brake fluid can be used and is recommended. the causes is most likely low fluid or worn out syncros in the tranny.. check the level of fluid in the clutch system and fill and bleed system at the slave cylinder. after that check fluid in the tranny. if all there is fine then i would recommend bringing it to a trans shop for diagnosis. if the syncros are going out then you will be looking to spend between 750 and 1500 to have it rebuilt or 2000+ for a new trans

Posted on Aug 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a rover 45 2002 and cannot put car into gear when engine running. got told it was slave cyclinder but wasn't, any ideas??


try to bleed the system, if you have presure the clutch master cylinder is ok, but if the slave cylinder retracts by it self after holding the pedal , the slave is the problem, the slave is on the transmission, pushes the fork, the master is at the pedal where you apply the force.

Nov 28, 2014 | 2005 Rover 45 1.6

1 Answer

Clutch needs bled


check the fluid level in the clutch master cylinder reservoir. Get assistance and bleed the air out of the clutch system. IF there is a leakage at the slave cylinder and the vehicle is over 5 years old replace both the slave and the master cylinders.

Apr 05, 2014 | 1991 Mitsubishi Mighty Max

1 Answer

Changed slave cylinder will still not go in gear


if you bead the system and still have no pedal action the master cylinder would be bad if the fork arm is moving the pressure plate could be bad

Aug 01, 2012 | 1991 Dodge Stealth

1 Answer

I have a 91 acura legend and its very hard to shift gears


The problem is most likely the slave cylinder,or the master.You can try bleeding the system,this might help,but most likely you will be replacing a part(slave cylinder,or master).

Apr 30, 2012 | 1991 Acura Legend

1 Answer

91 nissan pathfinder 5 speedmanual.... Clutch pedal feels stiff and when i start it in gear the truck lunges forward like the clutch it still engaged.... Master and slave have been replaced and all hyd....


It really sound like you are going to need a new clutch. If the slave or master cylinders were bad they would feel loose, a stiff pedal usually means something came apart in the pressure plate.

Jun 03, 2011 | 1991 Nissan Pathfinder

2 Answers

2008 corvette 11,200 miles on it clutch won't release


YOUR WARRANTY SHOULD FIX IT. SHOULDNT HAVE TO FIX YOUR SELF.POSSIBLE CAUSE CLUTCH MASTER CYLINDER FLUID LEVEL.IF LOW CHECK MASTER CYLINDER SLAVE CYLINDER LINES FOR LEAKS FIX AND BLEED CLUTCH HYDRALIC SYSTEM.IF CLUTCH MASTER CYLINDER FLUID LEVEL OKAY.THE CLUTCH DRIVEN DISC PRESSURE PLATE NEED ADJUSTMENT.I WOULD LET YOUR FACTORY WARRANTY FIX IT.YOU SHOULDNT HAVE TO PAY ANYTHING.JUST MAKE SURE FLUID IN CLUTCH MASTER CYLINDER NOT LOW WHEN YOU TAKE IT TO DEALERSHIP.IF THEY CHECK IT OUT FIND ANY KIND NEGLECT TO VECHICLE.THEY WILL NOT PAY.THEY WILL FIX BUT YOU WILL PAY OUT OF POCKET EXPENSE.

Oct 14, 2010 | 2008 Chevrolet Corvette

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

1 Answer

Won`t go into gear.i changed the slave and master cylinder.any other solutions?


You still have air in the system. Have you bled it at the slave cylinder yet? If so try unbolting the slave cylinder and fully extend the cylinder, careful not to push the cup out. Sometimes you have to fully extend it and then bolt it back in place to get the air to move.

Jan 12, 2010 | 1991 Toyota Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14445 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...