Question about Cars & Trucks

Open Question

High beams don't work on my ford f53 - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

motor1258
  • 6674 Answers

SOURCE: My low beams work on my headlights but my High beams wont come on

Take a look at this link regarding DRL system. I know it's not exact truck but most of it would apply to yours too. It should give you hints on what to test & how.
http://www.fordf150.net/howto/drl.php

Posted on Mar 28, 2009

  • 14036 Answers

SOURCE: I have a 1999 ford explorer sport and low beams not workiing.

replace driver module relay .it controls the low beam lights.

Posted on May 03, 2009

  • 1 Answer

SOURCE: high beam lights and driving lights don`t work

Hi,
I got my daughter a 2003 Pontiac Sunfire. They are a lot of electrical work.
The problem is the wiring harness which splits and travels under the battery and the windshield washer reservoir. The wires oxidize and fall apart.
The low beams will work but if you turn on the high beams the lights will go completely out, right?
If this is the case I can pretty much guarantee that you will have to remove the battery, the drivers side front inner fender, the air filter housing, the air throat, and the windshield washer reservoir. You will then be able to open the wiring harness feeding the headlights. The wire that feeds your high beams is a pink wire. Test the wires from the harness plug (located just under the battery) to a point as close to the headlight as you can, Use a simple continuity tester. Also feel and bend the wires. If the insulation cracks and you see a green or lite blue powder then patch a new wire in.
All in all I found 4-wires which I replaced. Everything works now.
Good Luck,
Jay

Posted on Jun 15, 2009

  • 158 Answers

SOURCE: the low beams of my

mdsarnes, The first thing that I would check is the fuse for the low beams located in the engine compartment power distribution box. (Fuse box) GM does have a legend written right on the cover so you know which fuse to check. Also, when the low beams are on try and wiggle the connectors to each bulb. If these dont work, replace one bulb and see if it works. If it does then take the same bulb and try it on the other side. If you have a test light then you can test for power at the plugs before you purchase any bulbs. Good luck with this.

Posted on May 22, 2011

clifford224
  • 1975 Answers

SOURCE: I have a 2001 ford

There is a relay for the high beams that may be faulty. That relay is located in the power distribution box located under the hood of the vehicle in the engine compartment. The relay location will be in the "R5" position in that panel (see diagram of layout below). Other then that you could be looking at a bad switch or a wiring problem nut pretty sure this will be your problem. I hope this helps and good luck.


clifford224_609.gif

clifford224_610.gif

Posted on May 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Ford Focus high beams work low beams don t


un plug one of the light connectors and check for power and verify ground with a 12v test light tool (available for cheap at the part store.) if there is 12v present, and a ground when switched to low beam, remove the bulb, inspect the filament. you will likely find it just has two burnt light bulbs

May 04, 2014 | 2002 Ford SVT Focus

1 Answer

High beam headlights stuck on replaced switch same problem


It can be issue with headlight switch,but as its already been replaced.Try disconnecting high beam headlight wiring from headlight assembly and reconnect direct external wire from headlight switch to headlight assembly,then by switch see if headlight is getting off and turning on or not.
See below related help links,similar to your issue.Click the link below:----
Only high beams work but head lights not working on Ford F350?

http://howtobyme.blogspot.com/2011/11/only-high-beams-work-but-head-lights.html

----------------
Only high beams working on GMC Savana?---------- High beams stopped working but headlights still work? http://howtobyme.blogspot.com/2011/11/highbeams-stopped-working-but.html
---------- Working of Headlight switch? ----------

Both headlight bulbs blow together?
----------

Car headlight bulbs don't last long?

------------ Only one head light works on 2001 Dodge Caravan? http://howtobyme.blogspot.com/2011/11/only-one-head-light-works-on-2001-dodge.html

----------
these will help.
Thanks.

Nov 06, 2012 | 2007 Chevrolet Tahoe

1 Answer

The headlights do not come on but the high beams do this keeps happening and they say it blew a fuse do high beams and low beams run off a different fuse and would'nt a dead short be causeing this


Forget the dealer,they obviously don't care to help you

They say it is a fuse,why don't they resolve the issue

Go to a competent repair shop

Oct 27, 2012 | 2002 Ford Focus

1 Answer

High beam headlights don't work on 2003 ford explorer


Gotta be in the steering column somewhere!

Oct 07, 2012 | 2003 Ford Explorer

1 Answer

Low beam headlight drivers side don`t work. high beam it works.


Check tour bulbs first and replace if blown. If OK then check wiring backwards from light to dip switch.

Oct 05, 2012 | 1996 Ford Explorer

1 Answer

Bright lights work low beams don't2005 excursion


ck for power to bulbs ck fuses ck switch

Jul 29, 2012 | 2005 Ford Excursion 4x4

1 Answer

99 ford contour daytime running lights work, but high beams do not.


I live in Australia & I don't fully understand the term " daytime running lights " but high beam & low beam lights are on separate fuses as is the parking lights so you probably have a blown fuse, check all the fuses in the fuse box......hope this helps......cheers.

Jul 05, 2011 | Ford Contour Cars & Trucks

2 Answers

Ford 2003 Focus. Low beam headlights not working. Hi beam do. Can get low beam to come on if flip between hi and low but don't stay on.


That sounds like a problem with the high beam switch in the low beam position. The contact is bad or the detent retainer isn't keeping the contact engaged.

Jun 22, 2011 | 2003 Ford Focus

2 Answers

2005 Ford Focus ZX3 SES, the blue high beam indicator in the dash comes on with low beams, and goes off with high beams. The indicator is on at the wrong time! I have tried the following: The turn signal...


It sounds like you are confused about how your headlamp system is supposed to work. The DRL does not run on the High beam circuit, it runs on the low beam circuit. The fog lamps are supposed operate with the park lamps and also with the low beams, not the high beams. From your description, I would say that your system is operating as designed and you are having trouble telling High from Low. (Don't feel bad, that is why high beam indicators were invented in the first place.)

May 08, 2011 | 2005 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...