Question about Cars & Trucks

Open Question

Engine temperature sensor location vw polo 1.4tdi

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
3dmaster
  • 183 Answers

SOURCE: 2001 vw polo

Dear Customer,

1
check your sensors 1st,all sensors must be good

2
if all sensors are working good than check your engine firing sequence,some times happens when sequence was wrong,

3
check your exhaust and carborator tuning pin that creates the batter combination for firing in bore for batter performance & less emitions ,so check is it ok or not than go to your nearest service center that havad certified mechanics,

till you read this you had solve this problem definatly,

THNX

Posted on May 18, 2008

Ad
  • 155 Answers

SOURCE: How do I change the temperature sensor under the

It’s located on the driver’s side of the engine on top /side of the head.. midway.. I don’t think you need to remove the engine cover to see it.. if it is the correct one it will have a dark green top.. the bad version has a black top… but they can all go out to lunch on you if old enough.

To replace.. make sure the car is cool..
You need a hood tool.. or small pair of pliers to remove the retaining clip that holds it in place.
Place a rag under and around it to catch the coolant.. you will lose less than a half a cup.. if that.

Pull the retaining clip back toward you.. try not to drop it.. (another good reason for the rag)

Wiggle the sensor.. pop it out.. and replace with the new green top one make sure you clean the area well.. and when you reinstall the new one that the c clip goes back on straight or it will leak.

Once you see the part out of the box.. you will understand how it works

Start the car.. check for leaks.. run until warm with the heater on.. top up the coolant overflow bottle with distilled water.. (if more than a half a cup.. you should mix the proper anti freeze and distilled water and then top up with that)

Good luck

Posted on May 06, 2009

  • 169 Answers

SOURCE: sensor locations

air intake look at snorkel it could be part of mass air flow check intake for eng coolant

Posted on Aug 29, 2009

  • 21 Answers

SOURCE: MY VW POLO SHOWS FAULT CODE ; P0106 ABSOLUTE MANIFOLD PRESSURE SE

this a map sensor, probably just need the sensor replaced, it measurese intake vaccum and adjusts air/fuel mixture accordingly

Posted on Oct 07, 2009

Testimonial: "MANY THANKS TO HONDABOY 47. SPOT - ON. PROBLEM SOLVED!"

smhb1
  • 146 Answers

SOURCE: crankshaft sensor for vw polo where is the

Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing

Posted on Sep 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My VW Polo 2002 1.4i engine cooling light has suddenly come on. What should I do? Is it the temperature sensor?


CHECK ENGINE COOLANT LEVEL SOUND LIKE COOLANT VERY LOW IN RADIATOR.ADD MORE COOLANT TO THE CORRECT LEVEL.

Mar 01, 2011 | Volkswagen Polo Cars & Trucks

2 Answers

Crankshaft sensor for vw polo where is the


Crankshaft sensor is located on the right side of the cylinder block behind or under the starter. It is fitted into the rear crankshaft oil seal hausing

Sep 12, 2010 | 2002 Volkswagen Passat

1 Answer

VW Polo engine cut-out


Tty a temperature sender unit.

Sep 11, 2009 | 2004 Volkswagen Golf

1 Answer

Location of temp.control sensor on vw polo 2002 1.2


Hi rabing

This sensor is located in cylinder head. Depending on engine code, this sensor is also a sensor for tick-over fuel / air mixture. If this is the case there will be 4 wires fitted to it
John

Aug 30, 2009 | 2002 Volkswagen Jetta TDI

2 Answers

2003 VW Polo 1.2 - Won't start when the engine is warm!


hi come across this on skoda same engine changed the g62 temp sender fixed this problem we had it was only £15.00

Jun 10, 2009 | 2005 Volkswagen Jetta

1 Answer

Vw polo keeps overheating and the fan dont come on what could it be


Volkswagen 2002 Polo

I take it you have the radiator full and the drive belts properly tensioned.
Here is the ordered check list;
1) Get the error codes read-out. Many chain auto part stores will loan a meter to get this for free. Call. They may be mis-leading because of other problems, but may still be useful.
2) Check the fuses
3) If the radiator fan is not running while the car is hot you may need to check the thermal switch. This switch will turn on the radiator fan. If the connection to the switch was good, you may need to replace the switch. I believe the switch is in the lower section of the radiator with wires connected to it.
4) Check the thermostat and its housing for damage. Water has to flow through it.

I believe the temperature sensor that you see displayed on the dash is located on the engine near the heater hose. if everything else checks ok you may check this for false readings.

The problem should be corrected for the temperature sensor. The engine can be in hot/cold start mode and Lambda probe would get the wrong info.

May 17, 2009 | 2002 Volkswagen Jetta TDI

4 Answers

VW Polo Map sensor fault code idling pooly


Hi, I have a 2001 polo 1.4 mpi it lackes power when you hit a hill it just dies, It has had new cat, fuel filter, fuel pump and throttle body, but is still the same it just dose not want to give me full rev's?

Mar 30, 2009 | 2002 Volkswagen Golf

2 Answers

2001 vw polo


Dear Customer,

1
check your sensors 1st,all sensors must be good

2
if all sensors are working good than check your engine firing sequence,some times happens when sequence was wrong,

3
check your exhaust and carborator tuning pin that creates the batter combination for firing in bore for batter performance & less emitions ,so check is it ok or not than go to your nearest service center that havad certified mechanics,

till you read this you had solve this problem definatly,

THNX

May 18, 2008 | 2001 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...