Question about Chevrolet HHR

Open Question

Tools needed to replace alternator in 2007 hhr

Alternator replacement

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
keemo68
  • 1263 Answers

SOURCE: 2007 HHR Wiring diagram

is there spark? is their fuel? also if it was wrecked chances are that the fuel cut-off switch was triggered. i have not ever worked on one so i don't exactly know where it is but i would check behind the fabric/hard plastic right rear/left rear wheel hosing and see if you can hit the reset switch. another suggestion is go to napa or oreillys and get a repair manual for it it has diagrams and schematics in it and it cost about 20 bucks.....good luck please rate this.....thanks

Posted on Sep 01, 2008

Ad
txkjun
  • 409 Answers

SOURCE: how do i replace the alternator on mazda mpv 2000?

Remove negative (-) battery terminal from battery. Remove drive belt from alternator pulley. Remove wiring harness (electrical connections) from alternator. Remove attaching bolts for alternator. Pry out alternator. Reverse steps to reinstall. 

Posted on Dec 28, 2008

  • 1 Answer

SOURCE: REPLACE ALTERNATOR 98 MAXIMA

Try checking a Maxima forum you have a 4th generation Maxima for instruction on how to replace the alternator. I have a Haynes Publication on that model car, but I not an easy proceedure to do. You have to raise up the car and remove it from the bottom.

Posted on Mar 15, 2009

  • 2 Answers

SOURCE: 98 saturn sl1 won't start

I have a 98 Saturn SL1 from time to time it would not start, it wouldn't even try. I knew the battery was good. It turned out to be the cranshaft position sensor.

Posted on Jul 22, 2009

roniecon
  • 6826 Answers

SOURCE: need a wiring diagram for a bosch alternator

If you ask for a one wire delco alternator,all you have to do is connect the large wire on back of the alternator to the positive battery post on the battery.The alternator is self energizing,there for no problem with wiring up a harness.If I can help,let me know my name is Ron.>>>roniecon@gmail.com

Posted on Aug 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I connect the battery the blinkers come on constantly glowing, nothing else works, check the fuses, the alternator fuse is blown, replace that, connect the battery fuse blows again. 2007 solara.


Bad alternator or short in alternator wiring. You much need a wiring diagram. Is that the car? Was in an accident? You may have pinched wiring or a wire shorted to ground. Try new fuse with alternator disconnected, then with key on, connect alternator-watch for sparks, or clicks, -you might want to have the alternator tested, just to be sure. You have to start somewhere...
Maybe a wiring short in the blinker system? Or is the fuse blowing an alternator fuse?

Oct 23, 2016 | 2007 Toyota Solara

1 Answer

Replacing alternator belt on 2007 1.3 cdti combo is it easy to do


Loosen alternator, push it towards the block until belt is loose. Pull the belt off and replace. Once the new belt is on push the alternator away from the block until belt is tight and tighten bolt/bolts. You might need a bar to keep tension on the alternator while tightening bolt/bolts.

Oct 18, 2016 | Cars & Trucks

1 Answer

Why do gauges keep flickering on and off at all speeds and blinkers tend to work on and off?


Do the headlamps flicker also ? Possible excess AC voltage ripple from alternator ! Suggest you take it to a ASE certified repair shop an have it checked out . If it is excess AC voltage ripple it could damage complex electronic components , engine computers ,abs modules , instrument clusters , body control modules etc.... Hope this helps .

Aug 23, 2015 | 2007 Chevrolet HHR

2 Answers

I have a Chevy hhr and there is a clicking noise when I try to start the car. Please help


If the battery is fully charged, the starter solenoid may be weak

May 16, 2013 | Cars & Trucks

1 Answer

My chevy 2007 hhr doesn't seem to be charging the battery, it's a new battery


run engine get meter for V,has to be 14.5+V.if less replace alternator.

Mar 03, 2013 | 2007 Chevrolet HHR Fall

1 Answer

2006 chevy hhr wont start and is making a clicking noise and the dash lights are flickering on and off


the starter could have a short in causing it to that. are the batter is dead or you need a new alternator

Jan 10, 2012 | 2007 Chevrolet HHR Panel LT New Cars

1 Answer

How to replace alternator on 2007 toyota tundra


Hi. Please see procedure below:

Determine which alternator your Toyota Tundra will need. You'll want to be sure the new alternator is compatible with your Tundra's engine. Models built from 2000 to 2004 have a 3.4 L or 4.7 L engine. Models made from 2005 to 2006 offer options for a 4.0 L or 4.7 L engine. Starting in 2007, the Tundra is available with 4.0 L, 4.7 L and 5.7 L engines.

Disconnect the negative battery cable with a socket wrench. Remove the gravel shield if you need to access the alternator from under the car. Remove the electrical connector and unfasten the retaining nut on the alternator terminal with a socket wrench. This will allow you to remove the battery terminal wire.

Unfasten the lock nut, pivot bolt and adjusting bolt on the alternator with a socket wrench. Remove the drive belt and take the alternator off the vehicle.

Install the new alternator assembly. Use a torque wrench to tighten the lock nut to 25 ft. lbs. and the pivot bolt to 38 ft. lbs. Attach the adjusting bolt.

Connect the electrical harness and battery terminal wire to the alternator and fasten the retaining nut to the alternator terminal with a socket wrench. Install the gravel shield if you removed it. Replace the drive belt and restore it to the proper tension. Reconnect the negative battery cable with a socket wrench.

Thanks!

May 25, 2010 | 2007 Toyota Tundra

1 Answer

Hello, 2008 hhr, battery went dead,replaced, went dead again over night, re-charged and now i have no power at all, chacked all fuses and they are good ?


the alternator as got one way diodes in it. charge up the battery and disconnect the negative battery terminal for a few hours etc, put the lead back on , if it starts you need a new alternator, the alternator will of been discharging to earth when not running, good luck.

Mar 06, 2010 | 2008 Chevrolet Hhr

1 Answer

How to change front disk brake pads on a 2007 chevy hhr


good day,

although it can be done yourself, i suggest that you seek assistance from a competent technician from chevy when replacing your brakepads since this involves proper settings and allignments. it may also need special tools to disassemble and reaasemble the unit.

i hope this will help

Oct 13, 2008 | 2007 Chevrolet HHR Special Edition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...