Question about Dodge Cars & Trucks

1 Answer

Water in engine oil - Dodge Cars & Trucks

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,113 Answers

If that isn't an indicator of a cylinder head gasket leak then there must be a crack in the block. It could also be from recently power washing the engine and not having a good gasket seal on your oil pan or similar.

Posted on Nov 28, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why engine oil and water mixed in mazda3


Um, most likely not good. Most likely means the block is cracked allowing the water and oil to mix. Major engine repair.

...

May 16, 2016 | Cars & Trucks

1 Answer

How to replace oil; cooler on this year


  • Service and Repair
Oil Cooler Replacement

Removal Procedure

  1. Raise and support the vehicle. Refer to Vehicle Lifting.
  2. Drain the engine oil and remove the oil filter housing.
89116492

  1. Loosen the oil cooler outlet (1) and the inlet (2) lines from the engine block.
  2. Lower the vehicle.
  3. Remove the intake plenum.
  4. Remove the intake manifold.
89116493

  1. Disconnect the following electrical connectors from the water crossover:
    • The engine coolant temperature sender (2)
    • The engine coolant temperature sensor (4)
84936658

  1. Remove the water crossover bolts (1).
  2. Remove the water crossover upper and lower seals (2).
84942881

  1. Loosen the upper heat shield bolts on the left side of the exhaust manifold.
89116496

  1. Remove the oil cooler outlet line from the engine oil cooler.
  2. Remove the oil cooler inlet line from the engine oil cooler.
84942883

  1. Note the positioning of the 4 seals.
84972057

  1. Position the oil feed and return,lines out of the way and secure with mechanic wire.
  2. Remove the engine oil cooler, inlet and outlet nuts (1).
  3. Remove the engine oil cooler cover bolts (2).
84942883

  1. Remove the engine oil cooler cover.
  2. Remove the engine oil cooler.
  3. Clean all sealing surfaces.
Installation Procedure
84972056

  1. Install the engine oil cooler.
  2. Apply a 2 mm (0.08 inch) bead of RTV silicone sealant, GM P/N 12346240, in the groove around the engine oil cooler cover.
  3. Install the engine oil cooler cover.
Notice: Refer to Fastener Notice in Service Precautions.
84972057

  1. Install the engine oil cooler cover bolts (2). Tighten the engine oil cooler cover bolts to 30 Nm (22 ft. lbs.).
  2. Install the engine oil cooler inlet and outlet nuts (1). Tighten the engine oil cooler inlet and outlet nuts to 20 Nm (15 ft. lbs.).
  3. Reposition the oil feed and return lines.
84942883

  1. Install the oil cooler outlet and install the oil cooler inlet lines to the engine oil cooler. Use 4 new seals.
Tighten the oil feed and return lines to 30 Nm (22 ft. lbs.).
84936658

  1. Install the water crossover:
    • Position the crossover.
    • Install the upper and lower seals (2).
    • Install the water crossover bolts (1). Tighten
Tighten the water crossover bolts to 30 Nm (22 ft. lbs.).
  1. Connect the electrical connectors at the following locations:
    • The engine coolant temperature sensor (4)
    • The engine coolant temperature sender (2)
  1. Install the intake manifold.
  2. Install the intake plenum.
  3. Raise the vehicle.
89116492

  1. Install the oil cooler outlet (1) line to the engine block. Tighten the oil cooler outlet (1) line to 30 Nm (22 ft. lbs.).
  2. Install the oil cooler inlet (2) line to the engine block. Tighten the oil cooler inlet (2) line to 30 Nm (22 ft. lbs.).
  3. Install the oil filter housing to the engine block. Tighten the oil filter housing to 45 Nm (33 ft. lbs.).
  4. Lower the vehicle.

Dec 22, 2014 | 2001 Cadillac Catera

1 Answer

Added coolant to resovoir yesterday today its empty where did the coolant go


as you said the expansion tank is running out of water and the engine oil level is getting higher. Question: does your oil become creamy color or not. If is a creamy color means that the water gets into the oil. Now check whether your engine is fitted with an oil cooler by the engine oil filter. if so possible is that, Is mixing the water with the oil, Replace the oil cooler. If not fitted then the things are getting worse.

Either you do have a cracked compression Gasket or a cracked cylinder head,depends to the water temperature you do have,or the engine behaviour.

Aug 28, 2014 | 2003 Pontiac Grand Am

1 Answer

VZ commodore alloytech motor, oil in coolant but no water in oil


Just because you have no water in the oil, you cannot rule out a head gasket issue or a cracked head. Do a bleed-down test.

Aug 14, 2014 | Cars & Trucks

1 Answer

VZ commodore alloytech motor, oil in coolant but no water in oil


It could be a crack or head gasket, when the engine is cold the steel is contracted and there is little water pressure, when you start the engine the oil pressure comes up quick and stays above the coolant pressure, I believe the radiator cap is set at 19-23lbs before it pushes past it. When the block heats up the steel expands and opens the crack or pushes by the head gasket.

Aug 14, 2014 | Cars & Trucks

2 Answers

My problem is toyota 2lt engine oil in water the oil is clean


Check the engine's oil dipstick. Brown, bubbly oil or any inconsistencies or traces of water on the dipstick can be symptoms of a severe head gasket failure. Have the car's engine checked right away. god bless!

Apr 03, 2014 | Cars & Trucks

1 Answer

Water in oil


Water in oil is usually caused by a cracked engine block. This is a serious problem which could have been caused by the water freezing inside the engine. Water freezing in the engine could be caused by insufficient anti-freeze in the water. Of course the other possible cause of finding water in the oil could be by a defect in the metal structure of the engine block. Either way....that indication usually points to a worthless engine.

Mar 20, 2014 | 1993 Chevrolet Cavalier

1 Answer

I have oil in my water resivior and its overflowing with oil.


Sounds like you have a leak that may be due to a bad seal,a bad gasket or a cracked head. When the engine is running. Oil pressure is higher than water pressure. But when the engine is shut off oil pressure goes to zero but water pressure is still at 15 psi. untill the engine cools off. that's when you get water and oil to mix. If you do an oil change you could find water in the oil pan. Doing a water pressure test will verify a leak but won't tell you where.

Nov 23, 2010 | 1999 Cadillac Catera

1 Answer

1999 tahoe 5.7L has a problem. Water mixed with engine oil.


If it was not overheated real bad the intake gaskets are a big problem on those engines

Nov 04, 2009 | Chevrolet Tahoe Cars & Trucks

3 Answers

Nissan Sentra GA14 engine - Water in Engine Oil


If the engine has been flushed well including the radiator and you are still getting water in the oil. The culprit is the cylinder head or the block has a crack internally allowing water into the oil.

Oct 10, 2009 | 1997 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...