Question about 1993 Ford Ranger SuperCab

Open Question

REPLACE THE FREEZE PLUGS 1993 FORD RANGER

REPLACE RTHE FREEZE PLUGS ON A FORD RANGER

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1993 ford ranger supercab

the fuse box is inside the pickup under the drivers side dash, there is a flasher which is the round one in the fuse box, it controls turn signals and emergency flashers also in the same fuse box, there is a 15 amp fuse which controls just the turn signals it sits vertical instead of horizontal.

Posted on Oct 23, 2008

Ad
  • 180 Answers

SOURCE: freeze plug needs to be replaced on 1994 Ranger

May help if you raise engine a little. But the other freeze plugs are most likley in same shape.

Posted on Feb 18, 2009

bschilz
  • 2049 Answers

SOURCE: How do I replace the fan belt on a 1993 Ford

You have a serpentine belt. Depending on your engine size, choose the following diagram to help put the belt back on.
V-6 2.3L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7007
V6- 3.0L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7012
V-6 4.0L http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7008

Follow this link for a video on how to replace a serpentine belt...
http://www.wonderhowto.com/how-to/video/how-to-inspect-and-replace-your-car-s-serpentine-belt-267229/

Posted on Sep 06, 2009

batviper
  • 120 Answers

SOURCE: HOW TO INSTALL CAM SENSER ON 1993 FORD RANGER 4.0

its right behind the intake manifold. its a B*&^h to get off but you need a special tool you can get a most auto part stores. you have to make sure your #1 piston is TDC on your compression stroke. then drop in your sensor, align it to what your specs say

Posted on Nov 18, 2009

  • 1129 Answers

SOURCE: 1993 ranger sputters until warm?

replace the Oxygen senson before catalytic converter this sensor tells the computer to send signal to fuel injectors to allow rich mixture upon start up for warm up then leans out mixture as it heats.

Posted on Feb 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing heater core 94 mazda b2300 2.3


This is a re-badged Ford ranger so watdh the video of rthe ranger heater core change out. How To Replace Heater Core On Ford Ranger

Dec 05, 2016 | Mazda B2300 Cars & Trucks

1 Answer

1993 ranger 2.3L idles ok but will not rev up.


does it have an accelerator cable ? if not , it may have an electronic
accelerator... and that could be faulty

Apr 14, 2014 | 1993 Ford Ranger SuperCab

1 Answer

Need diagram for distributor cap and spark plug wires to a 93 ford ranger 3.0. Any helpwould be appreciated


1993 Ford Ranger 3.0 liter V-6 VIN "U"

0f964b5.gif


Hope helps (remember rated and comment this).

Aug 19, 2010 | 1993 Ford Ranger SuperCab

1 Answer

I HAVE A 1993 FORD RANGER 3.0 V6 ENGINE AND NEED


For 1993 Ford Truck Ranger 4WD 3.0L MFI 6cyl the Control Module-Ignition is located under hood, center, rear engine area, mounted on distributor.

f2a2c92.jpg

Fig. 1: View of the remote mounted Ignition Control Module (ICM)

Hope this help (remember comment and rated this).

Jul 27, 2010 | 1993 Ford Ranger SuperCab

1 Answer

How do I go about changing oil in my 93 Ranger manual trans?


Check and see if the is a drain plug at the back, bottom or side of the trany, open plug and let drain and then replace gear oil. Other plug will be half way up on the side of the trany.

Jun 12, 2010 | 1993 Ford Ranger SuperCab

1 Answer

How does the spring go in on replacing back brakes on 1993 ford r


They make a brake spring installation tool. You can use vise grips, or hook the spring on a screwdriver and get the edge of the screwdriver abve the pin, and pry up, might take a couple tries.

May 02, 2010 | 1993 Ford Ranger SuperCab

1 Answer

1993 ranger sputters until warm?


replace the Oxygen senson before catalytic converter this sensor tells the computer to send signal to fuel injectors to allow rich mixture upon start up for warm up then leans out mixture as it heats.

Feb 24, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Freeze plug needs to be replaced on 1994 Ranger


May help if you raise engine a little. But the other freeze plugs are most likley in same shape.

Feb 18, 2009 | 1989 Ford F 150

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...