Question about 2004 Jeep Grand Cherokee

1 Answer

The range of my remote door opener has decreased on my 2004 jeep grand cherokee; I have replaced the bateries and no improvement. Is there an adjustment on the car that may effect this.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Jeep Master
  • 1,348 Answers

The output of the transmitter needs to be checked.it is a rf type .
if not,the front end of the remote module is no good.
it is part of a module that controls alot of other functions.

Posted on May 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Keyless remote 1996 jeep grand cherokee laredo programing


Instructions
  1. Programming the First Transmitter
    • 1

      Unlock all of the Jeepicon1.png Grand Cherokee's doors and open the driver's side door. Keeping the door open, lock it using the manual lock on the door itself.

    • 2

      Put the manual key into the ignition and switch it to the "On" or "Run" position, whichever applicable, without starting the engine.

    • Sponsored Links

    • 3

      Point the remote at the receiver (located by the little bulb on the caricon1.png ceiling) and hold down the "Lock" button for up to 5 seconds.

    • 4

      When the driver's side door unlocks, you know the remote has been programmed correctly. If you are only programming one remote, jump to the next step. If not, manually re-lock the driver's side door and repeat steps 5 and 6 using each remote you would like to program and then continue.

    • 5

      Turn the key to the "Off" position and turn the ignition on immediately. This must be done within 20 seconds of programming the last remote. You're finished!

Sponsored Links

Read more: How to Program the Remote on a 1996 Jeep Grand Cherokee ' eHow.com http://www.ehow.com/how_7433787_program-1996-jeep-grand-cherokee.html#ixzz2KdCc5PQq

Feb 11, 2013 | 1996 Jeep Grand Cherokee

1 Answer

Difficulty to open doors with the remote control


Replace battery in remote
Look for slot near key ring slot prise open with small screwdriver
After changing battery press unlock button 6 times

May 31, 2010 | 2004 Jeep Grand Cherokee

2 Answers

2004 Jeep Grand Cherokee blend door replacement


its not the door its self that doesn't work,it is opened by a vacume valve and closed with a vacume valve,and it is not an easy job even for a mechanic

Dec 24, 2009 | 2005 Jeep Grand Cherokee

1 Answer

Remote won't unlock door lock


Not to bad. Just need to remove all bolts including the ones behind the control panels, and behind ashtray and the ones in glove box. More time consuming then anything. It may also be the battery in the remote itself. Or the remote needs replacement

Jul 09, 2009 | 2004 Jeep Grand Cherokee

1 Answer

The range of both of my remote unlock transmitters has decrease.


I have seen some autozone parts stores with keyless remote displays. These were used to see if your keyless was transmitting so they could sell batteries for them. You could try to use their display and see how much range you are getting. I have never taken apart the unit in the car, but if it does not have an antenna it must use the body as an antenna. You might want to try a Salvage yard to see where the mating part is and what the wires attach to.

Jul 01, 2009 | 2004 Jeep Grand Cherokee

2 Answers

Automatic door locks wont work on my 2004 jeep grand cherokee


There is a broken wire in the rubber casing between the door and the vehicle. Take the rubber casing off and you will more than likely find a broken wire or one about to break. Been there and done that.

Jan 16, 2009 | 2004 Jeep Grand Cherokee

1 Answer

2004 CHEROKEE, WONT RECONIZE DRIVERS DOOR OPEN,


its the ground wire for the driver door, and posably an ornge one, in the black shielding to the door they rip all the time but yet for some reason jeep has yet to make a recall. any who you disconect the battery then pull the shielding back and patch the wires together.

Dec 14, 2008 | 2004 Jeep Grand Cherokee

2 Answers

2004 GRAND CHEROKEE DOOR LOCKS


Ground wire (black) open between drivers door conector and door pillar due to flexing. Locate break and solder in some extra wire to relieve the stress when the door is used.

Sep 15, 2008 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...