Question about Cars & Trucks

Open Question

Diagrams for quantum timing on all pulleys d4d 2,5 engine diesel

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
simontricket
  • 235 Answers

SOURCE: Isuzu bighorn diesel 4jg2 engine timing diagram

http://www.jeepolog.com/UserFiles/downloads/trooper_manual.pdf

This site has it .

Posted on Aug 25, 2009

Ad
  • 277 Answers

SOURCE: Toyota diesel hilux D4D noisy engine.just

Take the Vehicle back to the Installer/Supplier, for a Free of Charge CHECK and ADVISE under New Engine Warranty. If the OIL PRESSURE is LOW, when starting up from COLD, there is a genuine fault, so do not drive any distance.
Regards,DT

Posted on Aug 28, 2009

  • 1 Answer

SOURCE: 120 series prado diesel d4d aircon and indicators not working

Hi,

Have any luck with this as I have exactly the same problem except the ign2 fuse under the dash also keeps blowing. Alternator does not appear to be charging either.

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove all the front covers on a toyota d4d diesel engine ?


i suggest that you get a workshop manual as if it has a belt there will be no gears
the belt runs the cam shaft/s and the fuel pump
if you have to get to where you want then all the cam pulleys , idlers , crank pulley, possible water pump will all have to be removed first but that will be explained in the workshop manual

Jul 10, 2016 | Toyota Cars & Trucks

1 Answer

My quantum start idle but does not rev up


My Toyota Quantum 2.7GL idles but does not rev up. i ve ...

www.fixya.com/.../t15670829-toyota_quantum_2_7gl_idles_but_not_re...
Jan 5, 2013 - My Toyota Quantum 2.7GL idles but does not rev up. i ve changed the fuel pump and filter but still it starts, idles - Toyota 2007 Quantum 2.7 question. ...SOURCE: 1985 toyota 4x4 22re missing and rough idle. Have you pulled ...
Toyota quantum d4d idle but when u rev it doesn't pick up ...www.fixya.com/.../t24694524-toyota_quantum_d4d_idle_but_when_u_...Jun 24, 2014 - Toyota quantum d4d idle but when u rev it doesn't pick up reves - Toyota 2007 ... what will cause the car not to start after cylinder head repairs?Toyota quantum 2.7gl idles but when u rev it doesn not pick upwww.fixya.com/.../t17117064-toyota_quantum_2_7gl_idles_but_when_...Mar 14, 2013 - Toyota quantum 2.7gl idles but when u rev it doesn not pick up reves - Cars ... I have a 2006 toyota quantum,the engine starts,i doesn't idle,no ... and rear wheels will not drive? just makes terrible fringing noise but will drive in ...VWVortex.com - help, volkswagen idles but wont rev up 2liter 16 ...forums.vwvortex.com > ... > Golf II & Jetta II

Dec 21, 2015 | Cars & Trucks

1 Answer

I REPLACE THE FUEL FILTER IN TOYOTA FORTUNER D4D.BUT THE INDICATOR IS ON LIGHT.HOW CAN I ERASE THE LIGHT


Replacing the diesel filter - Engines - Fortuner 4x4 Fans

www.fortuner4x4fans.co.za/...fortuner/.../382-replacing-the-diesel-filter/
May 15, 2013 - 12 posts - ‎8 authors Car: Fortuner 3.0 D4D 4X4 2010 ... It would also be great to have the knowledge if you need to replace it in the bundu. ... Unplug the top connector on the fuel filter ... Toyotacharged me over R400 labour to do a 5 min job! .... doesnt create an air lock or vacuum of some sort- its free but you have to ask for it. Low fuel warning light - Fuel
5 posts
May 31, 2014
ABS problems - Electrics
9 posts
Feb 26, 2014
Low Fuel light on permanently - Electrics
17 posts
Sep 26, 2013
D4D Fuel FIlter issues. - Others
20 posts
Jan 1, 2013
More results from www.fortuner4x4fans.co.za

Nov 23, 2015 | 2006 Toyota Fortuner 3,0

1 Answer

Where are Cam and crankshaft timing marks on nadia d4d engine


follow this link for a video showing change of timing belt , this will show the timing marks etc
Toyota avensis D4D 2 litre diesel timing belt installation

May 04, 2015 | Cars & Trucks

1 Answer

I have a 2006 d4d toyota landcruiser that wont start . it has been lyning up for two years now . when u try to start it with key it wil try to run for a spilt second but just cut out . we tryed to pull...


the D4D ENGINE on Toyota Landcruiser has electronic injectors common rail engine and there is the possibility for gummed injectors and also but quality of diesel fuel in tank. Change the fuel and filter,and also a fuel treatment additive to be use as soon as started. and remember for good also treatment with cleaning use 250ml 2-stroke oil in a tank full of fuel and carry on with this for a month filling. Tank full to empty position and then use 2-stroke every time

Sep 16, 2012 | 2006 Toyota Land Cruiser

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

1 Answer

Serpentine belt diagram for a 5.9 diesel with air and 9 pulleys


5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Sep 13, 2008 | 2008 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...