Question about 1993 GMC Sierra

Open Question

Tighten bolts on truck bed - 1993 GMC Sierra

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Torque for main bearings on a 2002 3.7 ltr. liberty?


the book is free to read? KJ
chapter 9s
(7) Before installing bolts, lubricate the threads
with clean engine oil, wipe off any excess oil.
(8) Install main bearing bedplate to engine block
bolts 11, 17 and 20 finger tight. Tighten these bolts
down together until the bedplate contacts the cylinder
block.
(9) To ensure correct thrust bearing alignment,
perform the following steps:
² Step 1: Rotate crankshaft until number 4 piston
is at TDC.
² Step 2: Move crankshaft rearward to limits of
travel.
² Step 3: Then, move crankshaft forward to limits
of travel.
² Step 4: Wedge an appropriate tool between the
rear of the cylinder block (NOT BED PLATE) and
the rear crankshaft counterweight. This will hold the
crankshaft in it's furthest forward position.
² Step 5: Install and tighten bolts (1-10) in
sequence shown in (Fig. 49) to 41 N·m (30 ft. lbs.).
² Step 6: Remove wedge tool used to hold crankshaft.
(10) Tighten bolts (1-10) again to 41 N·m (30 ft.
lbs.) PLUS 1/4 turn in sequence shown in (Fig. 49).
(11) Install main bearing bedplate to engine block
bolts (11-20), and torque each bolt to 28 N·m (20 ft.
lbs.) in sequence shown in (Fig. 49).
(12) After the main bearing bedplate is installed,
check the crankshaft turning torque. The turning
torque should not exceed 5.6 N·m (50 in. lbs.).

why not just read the chapter, here.

http://colorado4wheel.com/manuals/Jeep/KJ/

Jan 17, 2017 | 2002 Jeep Liberty

1 Answer

How to tighten cab mounts


Bolts located on underside of the truck. I believe that 6 bolts hold the cab on to the frame if its a crew cab. Four bolts can be seen from laying under the truck. You can see the rubber mounts that attach it the the cab from the frame. The other 2 in the back are on the floor board by rear seat or back panel. they connect to the frame also. Make sure the cab is aligned with the bed. It can be shifted. Make sure the bolts are straight and not leaning forward or backwards. Inspect the rubber cab mounts to make sure they are good. You will understand when you start investigating the mounting area.

Sep 11, 2016 | 2005 Ford F 350 Super Duty

1 Answer

Fuel tank and fuel pump removal on 1991 ford ranger


Open the hood and support it with the hood prop rod. Unhook the negative battery cable from the terminal with the battery wrench. Position the cable end away from the battery so that it cannot accidentally contact the battery during the rest if this procedure.

  • Disconnect the fuel filler neck from the side of the truck bed with the socket set. Unbolt the truck bed retainer bolts from the floor of the bed with the socket set.

  • Lift the bed up and off the Ranger's frame with the assistance of another person. Walk the truck bed off the back of the Ranger and set it off to the side.

  • Rap the rag around the tip of the screwdriver, place the tip against the fuel pump retaining ring and tap the screwdriver's handle with the rubber mallet to turn the retaining ring counterclockwise. Remove the ring by hand.

  • Disconnect the fuel pump wiring harness and fuel lines with the screwdriver. Lift the old pump out of the gas tank and insert the new pump in its place. Make sure the new pump occupies the same position and orientation the old pump had prior to removal.

  • Tighten the fuel pump retaining ring with the rag, screwdriver and mallet by rotating it clockwise. Reconnect the wiring harness and fuel lines with the screwdriver.

  • Lift the truck bed off the ground and place it back on the Ranger's frame with the assistance of another person. Make sure the fuel filler neck clears the frame and seats into the filler neck hole in the bed wall when you're lowering the bed onto the frame.

  • Reinstall the bed retaining bolts with the socket set and reconnect the negative battery cable to the battery with the battery wrench

  • Jul 16, 2016 | Ford Cars & Trucks

    1 Answer

    How do i remove the truck bed from 2005 chevrolet avalanch


    disconnect all electrical wiring that is attached to the bed then disconnect the fuel filler tube. there is 4 bolts that hold the bed to the frame that you will have to remove. some trucks the bolts are removed from inside the bed and others from under the bed though the frame. then get help to pickup the bed and turn it to gain access to the pump or remove the bed from the frame.

    Sep 19, 2014 | 2005 Chevrolet Avalanche

    1 Answer

    TRUCK BED SQUEAKS


    No idea without a good look but it could be the body retaining U bolts are loose ,oil the threads then leave for a day before tighteneing

    Sep 24, 2012 | 2004 Dodge Ram 1500

    1 Answer

    How to remove truck bed 2002 gmc sonoma


    There are 4 bed bolts under the bed on each side that need removed, also 1 bolt on each side for the ground for the tail lights, and 3 screws in gas door for the filler neck. And then get a couple buddies to help lift off the bed or use tie-down straps and an engine lift and lift the bed off.
    Thank you and good luck,
    Lee

    Nov 12, 2010 | 2002 GMC Sonoma Extended Cab

    1 Answer

    2000 Chevy Silverado 2500 6.0 litre fuel pump


    lifting the truck bed off the frame works best if you dont have a lift..take the fuel neck loose from bed and remove bolts holding bed to frame from the drivers side..loosen the bolts on passenger side..raise the bed on drivers side while watching bumper to bed clearance on passenger side.. you should get enough clearance to remove fuel pump from tank

    Dec 26, 2009 | 2000 Chevrolet Silverado

    3 Answers

    How do i get the old fuel pump off


    Remove the fuel fil hose,and vent hose,and remove fuel tank straps,with jack supporting tank,lower enough to remove wire connector,and fuel lines .Remove tank from under vehicle,and remove the ring retainer,and pull the fuel pump assem,from tank.Follow instructions in the box with the new fuel pump.

    Nov 13, 2009 | 1992 Dodge Dakota

    1 Answer

    How do you adjust the parking brake on a 1994 ford ranger,manaul trans,4wd


    Start by adjusting up the rear brakes, if those are tight and you still want to tighten up the parking brake running down the driver's side, outside the frame are the parking cables. somewhere around the back of the cab/front of the bed should be a plate with 2 cables and a bolt. tighten the bolt/nut up to make the parking brake tighter

    Oct 04, 2009 | 1994 Ford Ranger Supercab

    1 Answer

    Torque specs for truck bed mounts


    Torque specs are not important in this application, apply some thread locking compound and tighten the bolts.

    45-60 ft lbs is about right for the size bolts that are used on that box.

    Sep 22, 2009 | 2006 Chevrolet Colorado

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    18 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    77169 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22265 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...