Question about Chevrolet Cars & Trucks

1 Answer

How to remove the upper portion of back seat 1982 monte carlo

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Under the seat there should be 2 bolts (sometimes the factory didn't install them. the seat hangs on 3 hooks. push in on the top of the seat about 5" from the side and lift up. center next. then the other side.

Posted on Nov 29, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 4 Answers

SOURCE: ignition switch replacement 1983 monte carlo

you have to take off the steering wheel.if you dont have the right tools to do so i would not attempt it.the turn signal switch has to be moved it just pulls over the end of the column.then there is a torx head screw at about 1 oclock in the column that has to be removed.and the ign.just pulls out.the dimmer switch is kinda tricky.a locksmith usually dont charge to much to do this job.it would probably cost you more to buy the tools you need to do it yourself

Posted on Jan 22, 2009

  • 24 Answers

SOURCE: how do you remove the rear back seat to a 2002

Most cars that do not have bolts are hook at the front end of the seat. You need push down really hard on the front end of the seat and pull the seat forward and up. This will unhook the latch. Good Luck

Posted on Oct 06, 2009

  • 1 Answer

SOURCE: removing rear seat back

there my be bols holding the seats in place

Posted on Oct 21, 2009

  • 8404 Answers

SOURCE: What would cause a loud roaring in the back seat

I agree, either the wheel bearing or the ring bearing in the rear end. My Plymouth Fury III (that is going back a bit) had a cracked ring bearing and roared loudly.

Posted on Mar 28, 2010

SOURCE: 2004 monte carlo power seat does not move forward

get the penny out of the track.

Posted on Dec 14, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the back seat in my 1996 Chevrolet Monte Carlo?


REMOVE THE SEAT BOTTOM FIRST BY PUSHING THE LEADING EDGE OF SEAT TOWARD THE TRUNK UNTIL IT RELEASES. THEN REMOVE THE BOLTS AT THE BOTTOM OF THE SEAT BACK AND LIFT TOWARD THE ROOF TO REMOVE FROM ITS HANGERS

Mar 10, 2015 | 1996 Chevrolet Monte Carlo

1 Answer

How remove front seats from 02 monte carlo ss ?


Remove the plastic trim over the front and rear seat rails and you will see two bolts in the front and two in the rear, reach under the seat, disconnect the wiring to the seat and then remove front and rear bolts and careful pull seat out through the door opening, it is a tight fit don't damage anything, take your time.

Aug 29, 2012 | Cars & Trucks

1 Answer

Where do i find the thermostat on a 2000 monte carlo


Follow upper radiator hose to housing on engine Remove housing make note how thermostat is installed Clean both surfaces Install new thermostat.Locate the upper radiator hose and trace it back to the engine. It connects to the T-Stat housing with a band clamp.Thanks

Dec 08, 2010 | 2000 Chevrolet Monte Carlo

1 Answer

03 monte carlo ss power seat wont go down. how to fix?


i have a 2003 monte carlo and the wires came out of the plug under the seat. im trying to put them back in so my seat will be able to work. there are 12 wires that make up 6 connections. i need to know what wires go together. the wires are red with blue strip, red with green strip, red with white strip, yellow with blue strip, yellow with green strip, yellow with white strip, light green, green, peach, blue, light blue, and yellow.

Jun 08, 2010 | 2003 Chevrolet Monte Carlo

1 Answer

My 1996 monte carlo brake lights wont work?


You need to replace the stop light switch. Most are mounted on the upper portion of the brake pedal, on some vehicles they are attached to the master cylinder. It's an $8 part.

Nov 25, 2009 | 1996 Chevrolet Monte Carlo

1 Answer

How do you remove the rear back seat to a 2002 chevy monte carlo


Most cars that do not have bolts are hook at the front end of the seat. You need push down really hard on the front end of the seat and pull the seat forward and up. This will unhook the latch. Good Luck

Oct 05, 2009 | 2002 Chevrolet Monte Carlo

2 Answers

Can't get belt off


just rotate the belt in a clock wise direction

Jul 15, 2009 | 1996 Chevrolet Beretta

2 Answers

Vehicle compatibility


The "base" alternator in your car fits a wide range of vehicles. The pulley is easily removed with an allen key and wrench and the body can be taken apart and easily turned to match the plug position you need. (usually the rear portion is removed, brushes are re-installed and held in position with a paperclip,or toothpick, which is removed after the unit is bolted back together.

May 31, 2009 | 1984 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...