Question about 2009 Chevrolet Optra 1.6

Open Question

Remote control unit not working - 2009 Chevrolet Optra 1.6

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My aircon has stoped working..only thing i have done is replace batteries


Check if the batteries both are giving at least 1.5volts each. Clean the terminals of the remote control to secure proper contact with the batteries. Check if the negative terminal of the remote have enough pressure to keep the batteries firmly inside the remote control. Point the remote to the sensor of your air conditioner and press the power button. Changing direction of the remote control pointing to the air conditioner while pressing power button. If still air conditioner does not work clean the sensor eye to remove dust and switch again the unit.

Jan 05, 2018 | Cars & Trucks

2 Answers

I NEED A KEY CODE FOR THE BUILT IN RADIO IN A FORD FIGO 1.4 AMBIENTE 2012 MODEL


Try this, found it on another answer board.

Press and hold the Auto button. While holding the Auto button, push and hold the Track Up button. The “_ _ _ _” will disappear after about 5 sec. Enter KCAR using the remote control from a higher end CD Receiver or any Excelon CD Receiver. Enter "KCAR” with the remote controller as described below. “K”: Press TRACK UP key (>>|) after pressing 5 key twice. “C”: Press TRACK UP key (>>|) after pressing 2 key once. “A”: Press TRACK UP key (>>|) after pressing 2 key three times. “R”: Press TRACK UP key (>>|) after pressing 7 key twice. * If you commit a mistake in the code entry, the unit enters the code request mode again. Press the Track Advance button on the remote to enter the override code. The unit will enter the All Off or Standby mode if done properly. Video Unlock: Use a remote from a higher end CD Receiver or any Excelon CD Receiver. Some Video remotes will work, switch on remote must be set to AUD. Press 55222277 on the remote. There will be NO visual verification when entering the override code. Head units with a Up / Down Volume control buttons: Press and hold the Volume Up button. While holding the Volume Up button, push and hold the Disp button. The “_ _ _ _” will disappear after about 5 sec. Enter KCAR using the remote control from a higher end CD Receiver or any Excelon CD Receiver. Enter "KCAR” with the remote controller as described below. “K”: Press TRACK UP key (>>|) after pressing 5 key twice. “C”: Press TRACK UP key (>>|) after pressing 2 key once. “A”: Press TRACK UP key (>>|) after pressing 2 key three times. “R”: Press TRACK UP key (>>|) after pressing 7 key twice. * If you commit a mistake in the code entry, the unit enters the code request mode again. Press the Track Advance button on the remote to enter the override code. The unit will enter the All Off or Standby mode if done properly.

Read more: How can I get the key code for ford figo radio systems? - Radio system key code ford figo :: Ask Me Fast at http://www.askmefast.com/How_can_I_get_the_key_code_for_ford_figo_radio_systems-qna4609185.html#q2909005

Dec 09, 2015 | Ford Cars & Trucks

1 Answer

Remote not working


It could be many reason for remote is not working ,check the battery with replacing it with fresh new one , check the antenna for remote receiver and then check the connectors to remote receiver control unit under driver sit for loos connection ,if all seems ok you might replace unit

Feb 23, 2015 | 1996 Toyota Camry

3 Answers

Remote lock and trunk stopped working


Have you tried replacing the fuse?

Jun 07, 2014 | 2003 Chevrolet Impala

1 Answer

Pontiac Montana 2002 remote doorr locks stopped working


Hi steve
make sure the two remotes that you have, have a good battery
and do this procedure, you will be OK
Good luck

Feb 16, 2014 | Cars & Trucks

1 Answer

Lexus 93 ls400 remote not working for driver's door


if all other doors work the door lock actuator needs replaced most likely. if door switch works the same. if not then it could be a bigger problem in the circuit or remote control module. use a meter to test for signal to lock actuator. if no signal then ck control unit. if signal replace lock actuator.

Aug 19, 2012 | 1993 Lexus Ls 400

1 Answer

The drivr door lock does not work with teh remote control or with the door control. I have to set the lock manually.


If you have the battery of the remote control changed, and still not working, check on the transceiver unit inside the car.

Feb 28, 2011 | 2006 Hyundai Sonata

1 Answer

Power locks don't work with remote or control from


The door lock/unlock input from the driver's key switch goes to the Door Multiplex control unit (main switch), the Door multiplex control unit then sends a signal on the BUS (CAN) circuit to the passenger's multiplex control unit; the passenger's multiplex control unit then controls all the door locks. The passenger's door lock key switch inputs to the passenger's multiplex control unit, if the locks work from the passenger's side key switch but not the driver's side key switch, the most likely cause is the driver's multiplex control unit (main switch) not sending the signal to the passenger's side multiplex control unit. This could also be the drivers side door lock actuator. Hope this helps!

Jan 07, 2010 | 2003 Honda Pilot

2 Answers

I can't lock the car using the remote key. the light flashes on the key but does not lock the doors


try reprograming the remote, if that doesn't work u may need a new remote these are the factory instructions.
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound.
he "Open" button is pressed once for programming the first, or a single,
remote unit.
�� When programming additional remote units for the second, third or fourth
memory addresses, press the "Open" button two, three or four times, in
one-second intervals.
�� Example: press the "Open" button once, wait 1 second, then press once
again to program the second remote unit.
�� After 6 seconds, press "Open" button once to activate the coding ocess.

4. The remote unit will now be coded, and it can be used to unlock the central
locking system. Switch ignition off.

The key must be removed from the ignition before the remote unit can be used to lock
the vehicle.The coding process can be repeated up to 4 times for additional remote units.
In between each remote unit coding, the ignition must be switched off.

Apr 10, 2009 | 2004 Volkswagen Jetta

Not finding what you are looking for?
2009 Chevrolet Optra 1.6 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...