Question about Hyundai Excel

1 Answer

Hyundai excel how do I bleed the power steering fluid on a 1997 Hyundai excel

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Hi. turn engine on take cap off resovoir keep turning steering wheel from lock to lock periodically checking level in resovoir until air bubbles stop.

Posted on Nov 28, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
elias_sgr
  • 163 Answers

SOURCE: where do I check the

Remove Transmission Fluid Level Check
Locate and remove the transmission fluid level checker, in most cars and trucks this is where the fluid is checked and added.
1687565.jpg
Insert fluid funnel and add transmission fluid until the proper amount of fluid level is reached. Let engine warm and recheck fluid level, add fluid as needed. Do not over fill the transmission, it could foam the fluid and cause low fluid pressure causing premature transmission failure. recheck transmission for leaks and recheck fluid level in a couple of days.

DIAGNOSIS AND TEST FLUID LEVEL AND CONDITION
1. Park the vehicle on a level surface. 2. Before removing the dipstick, wipe all dirt from the area around the dipstick. 3. With the selector lever in "P" (Park) and the parking brake applied, start the engine. 4. The engine should be running at idle speed and the fluid should be at normal operating temperature [80-90°C (176-194°F)]. 5. Move the selector lever to every position to fill the torque converter and hydraulic circuit with fluid, then place the lever in the "N" (Neutral) position. This operation checks that fluid level check is accurate. 6. Check if the fluid level is in the "HOT" range shown on the dipstick. If the fluid is low, add automatic transaxle fluid until the level reaches the "HOT" range.
ab7f169.gif

Posted on Aug 13, 2008

MrScary66613
  • 1990 Answers

SOURCE: hyundai excel braking squeek when steering.

This is Caused by Worn Brake Pads. Get some new Pads Installed and it will fix this Problem for you. Please Rate my Solution, I need all the Help that I can Get! Thanks!

Posted on Jan 30, 2009

  • 2 Answers

SOURCE: WHICH POWER STEERING FLUID TO USE IN 2003 HYUNDAI

You must use the fluid type stipulated by the vehicle manufacturer as there are different specs for different vehicles.

The specification for power steering fluid should be listed in your owners manual. You can then purchase a quality brand at that spec.

If you don't have the owners manual ring the dealer service department or parts department and they will give you the correct specification for your particular model.

Posted on May 17, 2009

litoshop
  • 298 Answers

SOURCE: how d i change a clutch in a hyundai excel 1994

Hi first lift the car and be sure to secure the car that it wouldn't fall when your under the car, remove the wheels then disconnect the negative cable from the battery remove the axles, remove the transmission mount, remove the starter, remove the bolts around the transmission housing once you remove the bolts use a floor jack and put it under the transmission then use a prior and separate the tranny from the engine and bring the tranny to the floor now you have the clutch expose remove the old clutch and pressure plate and pilot bearing now do the same thing in reverse good luck

Posted on Sep 02, 2009

iambanshee74
  • 3489 Answers

SOURCE: spark plug gap for hyundai excel twincam 1998

these plugs should be NGK BKR5ES-11 or PK16PR11 ND and plug gap at .044". hope this helps. cheers.

Posted on Dec 03, 2009

Testimonial: "Thank you mate.Thanks a lot"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the bleed valve for a power steering box


Open the hood and check the level of the power-steering fluid by removing the power-steering reservoir cap. Add the correct fluid recommended in your owner's manual to bring the level up to the full mark. Be aware that fluid that looks foamy is an indication of air in the system. Replace the cap.
Locate the power-steering bleed valve on top of the steering box near the bottom of the engine bay. Follow the power-steering, high-pressure lines from the power-steering pump to the steering box if you have trouble locating it.
Push a 6-foot length of rubber hose onto the end of the bleed valve. Run the other end of the hose into a drain pan.
Start the engine. Loosen the bleed valve fitting slightly with an adjustable wrench in a counterclockwise direction. Turn the steering wheel all the way to its stop one way and then the other several times. Shut the engine off.
Close the bleed valve by tightening it with an adjustable wrench in a clockwise direction. Remove the power-steering reservoir cap, and add fluid to bring the level up to the full mark.
Observe the power-steering fluid that came out of the rubber hose into the drain pan. Repeat the above procedure if there are air bubbles in the fluid. Close the bleed valve and remove the rubber hose when there are no air bubbles in the fluid expelled from the bleed valve. Close the hood.
New Arrival V15 GDS VCI Diagnostic Tool for Hyundai and Kia

Sep 16, 2014 | Cars & Trucks

1 Answer

Power steering filter


drain the fluid at the large 24mm nut just crack it open and drain the fluid . then close the nut refill with power steering fluid .then bleed it with your cap off. turn full lock left and right a few times .than refit the cap.

Dec 28, 2013 | Hyundai Elantra Cars & Trucks

1 Answer

How to bleed hyundai excel radiator?


there should be a plug (small bolt) at the thermostat housing remove it while filling the radiator. replace it when coolant runs out without air pockets

Feb 02, 2012 | Hyundai Cars & Trucks

1 Answer

How to repair a power steering pump hyundai coupe 1996


SIPHON OUT POWER STEERING FLUID.USING A HAND PUMP SIPHON TYPE YOU BUY AT ANY AUTO PARTS STORES.PLACE DRAIN PAN UNDER CAR NEAR POWER STEERING PUMP CATCH FLUID WHEN YOU REMOVE POWER STEERING LINES AT THE PUMP.REMOVE DRIVE BELT.THEN REMOVE POWER STEERING PUMP.YOU NEED TO TAKE OLD PUMP WITH YOU.TAKE NEW PUMP AND OLD PUMP TO MACHINE SHOP THEY WILL REMOVE POWER STEERING PUMP PULLEY FROM THE OLD PUMP TRANSFER PULLEY TO THE NEW POWER STEERING PUMP YOU NEED TO BUY NEW POWER.STEERING HOSES O RINGS TO GO ON NEW POWER STEERING PUMP.HOSES THE OLD ORINGS WILL LEAK. THEN TAKE NEW POWER STEERING PUMP ON INSTALL IN VECHICLE THEN BLEED POWER STEERING SYSTEM.FILL POWER STEERING PUMP UP NEW FLUID.WAIT FEW MINUTES.WHEN LEVEL DROP ADD MORE FLUID UNTIL YOU GET TO FULL COLD MARK.START ENGINE 15 SECONDS SHUT OFF CHECK FOR LEAKS. NOW CHECK POWER STEERING AGAIN ADD TO FULL COLD MARK.NOW RAISE FRONT WHEELS OFF GROUND.START ENGINES TURN STEERING LEFT TO RIGHT WITH OUT STOPPING IT DO SEVERAL TIMES THEN CHECK FLUID.ADD TO THE COLD MARK DONT OVER FILL.IF FLUID LOOKS TAN HAS AIR BUBBLES IN SYSTEM WAIT A WHILE UNTIL FLUID SETTLE CHECK FLUID LEVEL.DONT DRIVE VECHICLE UNTIL STEERING FEELS NORMAL.AND IF YOU HEAR NOISES.LOCATE PROBLEM FIX BEFORE DRIVING VECHICLE.

Jan 24, 2011 | Hyundai Genesis Coupe Cars & Trucks

2 Answers

I have a 1987 hyundai stellar that the brakes ar,nt working on.I have changed the master cylinder but they still do,nt work.I,ve tried disconnecting the two lines coming out of the master cylinder to bleed...


you will have to remove the master and bleed it on the bench, connect lines from the ports into the master fluid, then bleed , then install the master and bleed it at the lines, still no pedal, bleed the system completely

Dec 04, 2010 | 1987 Hyundai Excel 4-Door

1 Answer

Power steering in hyundai xg350 doesn't work. Put


power steering need bleeding if your reservoir was dry when you added fluid if.fluid was okay not too low.your power steering pump could be faulty.the cold weather will effect it.

Dec 13, 2009 | 2002 Hyundai XG350

1 Answer

How do i bleed the brakes on a hyundai excel 1995 no fluid getting to rear brakes


log on to youtube type in(BLEEDING BRAKES)and it's there step by step.

Oct 02, 2009 | 1994 Hyundai Excel

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

246 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77194 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...