Question about 1997 Ford Crown Victoria

1 Answer

Change license plate lamp bulb rear - 1997 Ford Crown Victoria

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

The lens over bulb should be held on by two crosshead screws remove these and remove lens with rubber seal. take bulb out replace and put seal and lens back on with screws

Posted on Nov 28, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

AlmostBob
  • 550 Answers

SOURCE: change tag bulb 2000 focus

am not familiar with the early year Focus'. Look above the license plate, if the lens for the bulb has two screws, you need to remove them to access the bulb. On other models, open the trunk and look down where the license plate is, you should be able to see and access the bulb from there.

Posted on Jul 19, 2008

michigan man
  • 3533 Answers

SOURCE: how to remove the rear light on my Freestar license plate

in most cases you have to open the rear tailgate remove the panel and then you have access to everything in the door

Posted on Jan 04, 2009

  • 12 Answers

SOURCE: Need to change license plate light on 2004 F150

Try turning the socket that holds the bulb to the left and pull it out to get to the bulb some times these get so hot that they start to melt so it might be hard to turn

Posted on Mar 13, 2009

c17hydro
  • 2984 Answers

SOURCE: how to change the license plate light on 2001 ford focus zx3

Take a thin blade screw driver and gently pry between the rubber seal and the metal and pop the light out, replaced the bulb and pop the light back in. works fine.

Posted on Mar 22, 2009

  • 20 Answers

SOURCE: Replace license plate bulbs on 2003 ford focus

if you buy some of those "on tv only" lights that are bubble shaped and plastic, you can duct tape those onto your license plate area and click them on or off when needed.

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change license plate bulbs in 2004 buick lesabre custom


  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove the tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.

Sep 22, 2014 | 2004 Buick LeSabre

1 Answer

How do I change my license plate bulb?


{: ) You need to remove first the screws from the license lamp, afterwards you can remove the license lamp from the rear compartment lid. Then ypu have to remove the bulb/socket from the license lamp by rotating counterclockwise. You may remove now the bulb from its socket ( if required).

Aug 31, 2011 | 2003 Oldsmobile Alero

1 Answer

How do I replace a rear license plate bulb in 2004 Jeep Liberty?


  1. Remove the screws that secure the license plate lamp assembly to the rear bumper fascia
  2. Pull the license plate lamp assembly down and out through the mounting hole in the rear bumper fascia far enough to access and disconnect the wire harness connector.
  3. Remove the license plate lamp assembly from the rear bumper fascia.

Apr 16, 2011 | 2004 Jeep Liberty

1 Answer

Tag light is not working. is there a fuse that will get the light turned back on?


The fuse labeled REAR PARK LP 15A in the right instrument panel fuse box powers the rear park lamps, and the tag lamps. If your rear park lamps are working then you most likely need to replace the tag lamps (bulbs). Use the following procedure to replace the lamps.

To Remove:
  1. Remove the two mounting screws from the license plate lamp.
  2. Remove the license plate lamp from the rear bumper fascia.
  3. Remove the license plate lamp socket by turning it counterclockwise.
To Install:
  1. Install the license plate lamp socket by turning it clockwise.
  2. Position the license plate lamp to the rear bumper fascia.
  3. Install the license plate lamp mounting screws.

Feb 17, 2011 | 2004 Chevrolet Impala

1 Answer

Change tag light bulb


  1. Remove two screws retaining the lamp to the rear license plate lamp shield.
  1. Rotate socket one quarter turn from backside of lamp and remove the miniature bulb (13466) .

  1. Install new miniature bulb into socket.
  1. Install socket in lamp .
  1. Secure lamp to rear license plate lamp shield with two screws and tighten to 2 Nm (18 lb-in).


    ak1473a.gif


    Item Part Number Description 1 13508 Rear License Plate Lamp Shield 2 14A583 Lamp Lead Wire 3 383356-S Nut (4 Req'd) 4 56000-S Screw (4 Req'd) 5 13550 Lamp (2 Req'd) 6 13466 Miniature Bulb (2 Req'd) A — Tighten to 2 Nm (18 Lb-In)

Feb 27, 2010 | 1998 Ford Windstar

1 Answer

2007 Pontiac G6. Rear license plate bulb socket dead


park lamp and license plate share same fuse.check park lamp fuse.if fuse good you have ground wire problems.

Nov 30, 2009 | 2007 Pontiac G6 GT Convertible

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

License plate bulbs on 98 Park Avenue


License Plate Lights Removal & Installation 1997 – 2000 To Remove:

License/backup Lamp Assembly


76707d9.gif

  1. Remove the rear compartment lid trim. (if necessary)
  2. Disconnect the license/backup assembly connector from the body harness.
  3. While removing the license/backup lamp assembly from the rear compartment lid, disconnect the harness grommet from the rear compartment lid.
  4. Remove the license lamp housing from the license/backup lamp assembly.
  5. Remove the license lamp bulb from the housing and socket.
To Install:
  1. Install the license lamp bulb into the socket and housing.
  2. Install the license lamp housing onto the license/backup lamp assembly
    • Torque the fastener to 18 in-lb (2 Nm).
  3. While holding the license/backup lamp assembly, install the harness grommet to the rear compartment lid.
  4. Install the license/backup lamp assembly
    • Torque the fasteners to 53 in-lb (6 Nm).
  5. Connect the license/backup assembly connector to the body harness.
  6. Install the rear compartment lid trim. (if necessary)

Jun 30, 2009 | 1998 Buick LeSabre

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

1 Answer

How do i get the cover off the license plate bulbs?


REMOVAL PROCEDURE
  1. Disconnect the tail/back up lamp harness connector from the from the body wiring harness.
  2. Remove the tail/back up lamp assembly from the rear compartment lid.
  3. While supporting the tail/back up lamp assembly, unplug the tail/back up lamp harness grommet from the rear compartment lid and remove tail/back up lamp from the vehicle.
  4. Remove the license plate lamp bulb from the lamp housing.
INSTALLATION PROCEDURE
  1. Install the license plate bulb into the lamp housing.
  2. While supporting the tail/back up lamp assembly, install the tail/back up lamp harness grommet to the rear compartment lid and install the tail/back up lamp. NOTE: Refer to Fastener Notice in Service Precautions.
  3. Install the tail/back up lamp fasteners to the tail/back up lamp studs. Tighten Tighten the tail/back up lamp fasteners to 6 N.m (53 lb in) .
  4. Connect the tail/back up lamp electrical connector.
  5. Connect the tail/back up lamp harness connector and clip the connector to the metal edge of the rear compartment lid.

Feb 25, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
1997 Ford Crown Victoria Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...