Question about 1994 Toyota Camry

2 Answers

When weather is damp car will not start

I have to depress gas pedal and keep turning engine over till it starts is this ok

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Have you tried wd40 in the coils

Posted on Nov 28, 2013

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 61 Answers

It is leaking injector, after a few crank take out the spark plug one by one to see they are wet and smell gasoline. If it does, check the fuel injector.

Posted on Apr 05, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 105 Answers

SOURCE: Car starts but need to apply gas to keep it going.

you are having a problem with your throttle body intake which is directly connected to your gas pedal and deals with the flow of gas from tank thru fuel line to fuel rail and then thru injectors which spray directly into engine. if you cant feed the engine fuel it will keep dying. also check out your intake manifold for leaks and cracks too.

Posted on Jul 26, 2009

  • 64 Answers

SOURCE: 1994 corolla: hard to start

If it is happening more frequently in cold or damp weather it could be a spark issue. Wet or damp weather can effect spark plug wires if there is even minor damage to them (usually occurs durring rain). The other things that come to mind are the fuel pump and lastly the fuel line check ball that is in the fuel tank. If it is leaking then all the fuel in the line will drain back into the tank over night (pressure lost in the fuel line) and this will cause repeated, extended cranking when you first start the car in the morning or after the car has sat for several hours.

Posted on Oct 06, 2009

Testimonial: "In my case, I strongly suspect it is fuel pump problem. Very helpful."

  • 280 Answers

SOURCE: car starts but the engine does not reve when I

either broken accelerator cable or broken throttle position sensor, open the bonnet and see if the gas pedal actually turns the throttle, if the throttle is turning then the fault is in the TPS - http://cgi.ebay.co.uk/TOYOTA-AVENSIS-CAMRY-RAV-4-THROTTLE-POSITION-SENSOR-GEN_W0QQitemZ260532390938QQcmdZViewItem?rvr_id=&rvr_id=&cguid=504ea2ab1260a0aad422e2a2ffc2aa49#ht_879wt_940
That should fix it, simple to fit. one out one in + reattach the connector.

Posted on Jan 26, 2010

  • 23 Answers

SOURCE: engine stalls when starting,will not idle.

throttle control module or fuel control module is bad

Posted on Mar 27, 2010

  • 117 Answers

SOURCE: Car will not start without pressing gas pedal to

Have the idle bypass valve checked, also called idle air control valve.
If that valve is stuck in the closed position, it's not allowing the fuel to bypass the throttle plate to keep it idling, resulting in stalling, but will keep engine running if the pedal is pushed down.

Posted on May 14, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

Car will not accelerate when gas pushed


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

2 Answers

Gear noise left front 2008 prius sound like a tire rubbing against a plastic fender but it is not and the faster you go the louder it gets . Even worse when you steer to the right. And quite to the left.


It's most likely a bad left front wheel bearing or possible tire noise, switch the left front tire with the rear tire and see if the noise changes. If not have the wheel bearing checked, it may need to be replaced.

Oct 02, 2011 | 2008 Toyota Prius

1 Answer

1995 gmc serria will not start no click from starter, manual trans


replace the starter. Being a manual transmission you should be able to pop the clutch to get it going till you replace the starter. If you don't know how to pop the clutch follow these steps. That way you can still drive the car. When need to.
  1. Get inside the vehicle and depress the clutch to shift the car into "Neutral." Insert the key into the ignition and turn it to the "On" position. This is the place the key would be after a normal turn of the ignition switch for starting. Instead, with a clutch pop, the ignition will already need to be on so that when the engine is turned over, the key is in the On position.

  2. Move the car in position to be pushed from behind or sent down a slope for the starting procedure. Check to see that the brakes will work when pressed and how hard the steering wheel will need to be turned before the vehicle is started. Power steering and brakes will make both systems work poorly until the vehicle is started.
  3. 3 Sitting inside the driver's seat with the clutch depressed, put the shifter into first gear. Keep your foot depressed onto the clutch and the brake pedal without depressing the brake pedal. Roll down the window and signal to your helper to push. As the car rolls, you will steer toward any slope that will assist the helper in getting the car down the street. Allow the momentum of the vehicle to increase to constant motion.
  4. 4 Release the clutch quickly and be prepared to throttle the gas pedal as the engine is turned over by the motion of the vehicle. When in gear, the engine will be forced to crank and the ignition will send a spark for a start. The quicker the vehicle is going before the clutch is released will determine how many times the engine will turn over. More cranks equal more opportunities to ignite the gas and air for combustion and the engine to start without a battery or starter

Dec 06, 2010 | GMC K1500 Cars & Trucks

2 Answers

Experienced recent cold weather. Car will not


It's flooded like you say.
If it's really flooded, you'll have to remove plugs and dry them off.
Install them.
Now when you crank engine, hold gas pedal to floor.
That will stop gas from spraying into engine.
You need to get the gas out of the engine for it to start.
Crank for 20-30 seconds with pedal to floor. Do this 3 times waiting 2-3 minutes inbetween cranks.
The starter needs to cool down.
Then after that start normally and see if it will start.
Remember if it will not start after 2 attempts, then the possiblity of it flooding is there and you'll have to clear out the gas by holding the pedal to the floor again.

Jan 15, 2010 | 1993 Oldsmobile Eighty Eight

1 Answer

1997 circuis


replace the crankshaft position sensor it sounds like it is braking down.

Feb 11, 2009 | 1997 Chrysler Cirrus

1 Answer

Car running problem


Ok Slow deceleration rev responce was part of the ECU software to keep the emissions down ,however if this has only just started you can try to reset the IAC valve ,the procedure is as follows.

Turn ignition key on ,unplug the IAC valve ,turn the key off ,replug the IAC valve. do this 3-4 times .Then start the engine while holding the gas pedal to 2000 rpm ,then slowley let the go of the gas pedal till the engine idles .

The IAC valve is located on the throtle body and has 4 wires to it.

Sometimes the throtle body needs to be cleaned and then reset.

Jan 02, 2009 | 1999 Daewoo Lanos

10 Answers

Oil light


Hi lady d tilli,

Take off the fuse cover on the drivers side of the dash. there should be a bunch of fuses. in the middle is a red button that says "reset." turn your key to the on position, but DO NOT START. press the reset button until the change oil light blinks, then turn the key back off it should be fine after that. for the 05's theres somthing you have to do with the gas pedal. i think you do the same, by turning the key on but not starting...and then tapping the gas pedal 3 times.

Hope this helps a bit,
Good luck,
Eitan.

Jun 09, 2008 | 2004 Pontiac Grand Am

Not finding what you are looking for?
1994 Toyota Camry Logo

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...