Question about 1999 Ford Ranger SuperCab

1 Answer

Pin fell out of shifter what do i have to do to put it back

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Well if it broke off,but there is still a little left u could just take a hammer and a pin and pound the little part of the pin thats in there out so it will at least fit on the shifter on the top of the transmission.or u could go to a junkyard and buy one,they only sell them for 20.00

Posted on May 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

A pin fell onto my foot from the steering colum while I was driving my Ford 150 truck, 4.6 liter. I can't figure where it goes, the shifter is now slopy and closer and even touches the dash when putting it...


looks like the shift lever pivot pin. Your description indicates that you are currently using the shift lever slot (the hole which the shift lever passes through) to actuate your gear selection. The fact it fell out, suggests it was originally installed upside down (wide end towards floor). May have to remove the cowling from around the steering column to find the proper location for the pin.

Jan 27, 2015 | Ford Cars & Trucks

1 Answer

Adjust shifter linkage


2002 neon is cable shift and usually the cable fits in brackets. there is alignment pin in shifter base. put a pin in to hold it in neutral position until you have the cables in place and all brackets tightened then remove the alignment pin and put console back together.

Jun 03, 2013 | 2002 Dodge Neon

1 Answer

Shifthow to put transmission in neautral on 91 ford f150 without shifter


IF ITS AN AUTOMATIC COUNT BACK 2 CLICKS FROM PARK AT THE TRANSMISSION LEVER ON THE ******

Oct 10, 2012 | 1991 Ford F150

1 Answer

Gear shift feels like a pin fell out. Seems to be flopping around. Won't engage in any gear.


Look at the tube the shifter goes into, is there a pin in a hole there? If not find it and reinstall the pin that retains the shift arm to the steering column barrel.

Oct 09, 2012 | Cars & Trucks

1 Answer

I can't put gear shifter into park


drop steering collum to replace lost screw and tighten all of the other shifter screws best solution is to replace the shifter tube ,plunger ,bushings and straps takes about an hour.do not forget to use loctite on the screws.

Oct 22, 2017 | 1997 Mercury Mountaineer

1 Answer

Shifter will not go into Park to Start Vehicle. I have to put into neutral to start. A little pin with threads fell onto my foot when this problem started.Where did this threaded pin come from?


I would say it came from the neutral safety switch. They used to be on the side of the transmission but now most are located at the bottom of the steering column. You'll probably have to get it replaced. Hope this helps.

Nov 06, 2011 | 2000 Ford Explorer

2 Answers

What causes the gear shifter to feel like there is no gears at all I can move the shifter all around no gears to be found


There is a bushing held in by a pin which attatches to a cable lingage. The cable and linkage fell apart . Its mainly a plastic bushing that came out cansmo_171.gifcansmo_172.gif

Sep 02, 2011 | 1998 Saturn SL

1 Answer

I recently replaced the manual transmission on my 1991 Geo Tracker. A small pin fell out of the shifter box when we turned the transmission on its side. Now the car won't go into 1st 3rd or 5th. What is...


This pin actually goes into the bottom of the shifter and allows it to push and pull the transmission into these gears. You will have to break down the shift box to get this pin back in. I can't find any diagrams online, but, if you go to advance or auto zone they can let you look in a manual.

May 20, 2010 | 1991 Geo Tracker

1 Answer

Shifter button fell out


Look under the grip. There should be either a pin or a set screw. Remove the pin/set screw and pull the shift lever up. The installation is the opposite. Good luck.

Aug 22, 2009 | 1999 Oldsmobile Intrigue

1 Answer

Shifter very loose wont stuck in gear i left it in (sunfire)


see if there is a shear pin that goes thrrough the connection. A shear pi is used to prevent evxcessive forcing and is supposed to break under conditions you described.. It is easily replaced with a new oin and light hammer. Good luck.

Mar 18, 2009 | 1995 Pontiac Sunfire

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

Related Topics:

141 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

fordexpert

Level 3 Expert

5575 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...