Question about 2006 Mazda 6

6 Answers

Check engine light want go off

My check engine light came on and stayed on. It don't drive different. can you help me with this

Posted by on

  • sandraf0123 May 09, 2009

    I have a code for my car it is P0455

  • Anonymous Mar 20, 2014

    Check engine light stays on ? Engine seems ok

×

6 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mazda Master
  • 6,674 Answers

Run over to an autozone, or pep boys for a free trouble code scan & go from there. Get back to us with codes if you need more help. Easier & cheaper than guessing.

Posted on May 09, 2009

  • Mike Butler
    Mike Butler May 09, 2009

    One of the most common causes of this code is the gas cap is faulty.
    Remove gas cap, clean all areas where threads meet, maybe a even apply a little vaseline to threads & "O'" ring seal, erase codes & try a gain & see what happens. If it came on not long after putting gas in it, then there's a good chance. If cleaning it doesn't remove the code, I'd buy a new one.


×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 68 Answers

You can go to autozone and have the error codes pulled off your car's computer for free. Then once you know the problem, you can decide whether to tackle it yourself or call a mechanic. Hope this helps.

Posted on May 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 316 Answers

Your check engine light is telling that a sensor somewhere has failed. If you take your car to your local "autozone" they will check it for you for free, and let you know what sensor has failed. From there, the actual replacement is up to you; I'm sure your autozone associate would be happy to show you the location of, and explain the process of replacing the bad sensor.

I hope this information helps you, and I wish you luck on your repair.

Posted on May 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

First of all if you have a autozone need you and take the car there they will test it for free but for the most part its a EGR valve,Vaccum line off or bad or a O2-Sensor get it on a machine and then you know what you need to repair Michigan Man.

Posted on May 09, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Mazda Master
  • 599 Answers

Car needs to be scanned,most big auto stores will do this for little or no charge, get back to me with the codes and we'll go from there. please rate my fix as i strive to be the best Thanks Ray

Posted on May 09, 2009

  • Ray Keckeisen May 09, 2009

    codePO455 is evaporative emission(EVAP),control system leak detected (no purge flow or large leak, bring the car to a shop that can do a smoke test,most shops charge very little for this test,this is the only way for sure to find the leak, please rate my fix as i strive to be the best. ps don't start changing parts without this test as it could get expensive,read my motto TEST DON'T GUESS, if you need more help get back to me and we'll go from there Ray

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 957 Answers

Have the computer scanned for active codes and write back. If you don't have a mechanic, AUTOZONE, PEPBOYS, and ADVANCE AUTO will do it for free.

Posted on May 09, 2009

  • larry blais
    larry blais May 11, 2009

    P0455 is an emission code. It reads, evaporative emission control system, gross leak detected. And also evaporator control incorrect purge flow. This has to do with your E-VAP system. Check your fuel cap, see if it is loose or if the O-ring is damaged. Also inspect your vacuum lines. see if one of them is cracked or broken.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine light is on


Hi there:
If it stays on, then you have a stored code that indicates a malfunction of some kind in your engine or transmission control systems.



The four most common Check Engine light scenarios and what to do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 22, 2012 | 2006 Mazda 6

1 Answer

My dashboard lights blink erratically. The check engine light then comes on and stays on while the RPM and oil gauge go crazy. Then all returns to normal with the exception of the check engine light


Check this about the four most common Check Engine Light scenarios and what to do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day

Aug 20, 2012 | 2005 Mini Cooper

1 Answer

1990 volvo 740 check engine light is on


Hi there:
When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.

The Four Most Common Check Engine Light Scenarios and What to Do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 06, 2012 | 1990 Volvo 740

1 Answer

Malfunction indicator light stays on when driving.


Scanned the computer in order to know what fault codes is stored there;

The Four Most Common Check Engine Light Scenarios and What to Do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

May 17, 2012 | 2008 Dodge Nitro

1 Answer

Engline service soon


Hi there:
When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.

The Four Most Common Check Engine Light Scenarios and What to Do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps.

Apr 28, 2012 | 2005 Nissan Sentra

1 Answer

Check engine soon light


Hi cura:
When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.

The Four Most Common Check Engine Light Scenarios and What to Do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps.

Apr 28, 2012 | Cars & Trucks

1 Answer

Service engine light flashes


Hi there:
When the light comes on, one or more diagnostic trouble codes (DTC) are stored in the engine control module. These DTCs remain even if the light goes out. To address a Check Engine Light problem, the DTCs are retrieved and the appropriate troubleshooting information is followed in order to determine the problem.

The Four Most Common Check Engine Light Scenarios and What to Do:
* The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

* The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

* The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

* The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps.

Apr 25, 2012 | 1998 Chevrolet K1500

1 Answer

Service engine light


The Four Most Common Check Engine Light Scenarios and What to Do

The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all -it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Mar 04, 2012 | 1990 Chevrolet Corsica

1 Answer

Check engine light code 0


The Four Most Common Check Engine Light Scenarios and What to Do


The Check Engine Light turns on and off or flickers.
If the Check Engine Light comes on in the city but goes off on the freeway, then the fault is present during city driving conditions. Pay attention to whether or not the vehicle runs or drives any differently when the Check Engine Light illuminates. If vehicle performance does change, drive the car as little as possible and take it to be checked by a service professional as soon as possible. If there is no change in vehicle performance, you can drive home, but have it inspected as soon as possible. In this condition, you run a risk of the vehicle dying or not starting.

The Check Engine Light comes on and stays on.
If the Check Engine Light illuminates constantly during driving with no noticeable driving or performance problems, there is a permanent fault in the emission control system. When this happens, the computer that controls the emission system usually has a backup program that runs while the fault is present. (These backup programs are often referred to as "limp home" mode programs.) You should get the vehicle serviced as soon as possible, but in most cases, the vehicle will continue to operate, though you run a risk of it dying or not starting.

The Check Engine Light illuminates, stays on, and there are performance problems.
This means that a vital component of your emission control and engine management system has a serious problem. It usually involves a component or system needed for the vehicle to run at all. In most cases, drive the vehicle as little as possible. In many cases, the vehicle is not safe to drive at all - it could stop or stall out at any moment. It is best to pull over to a safe place and have the vehicle towed to an automotive diagnostician for a thorough inspection and repair.

The Check Engine Light light comes on and blinks in a steady pattern while driving.
Don't confuse this steady pulsing of the Check Engine Light light (usually one or more flashes per second) with a flicker (see above). The Check Engine Light may stay on steadily or it may flash when the vehicle is accelerated. This is very serious. There is a severe failure of the emission control system that is causing the engine to misfire to the point that the catalytic converter is damaged each time the Check Engine Light flashes. It may mean that the catalytic converter is overheating to the point that it will glow red or, in extreme cases, start a fire on the underside of the vehicle. Immediately pull over to a safe place and have your vehicle towed to an automotive diagnostician for repair. Vehicles can be severely damaged and even destroyed by fire if this condition is ignored for too long.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.


Thank you for using FixYa, have a nice day.

Mar 04, 2012 | 1994 Acura Vigor

1 Answer

Would faulty EGR valve cause check engine light to come on?


If EGR was out your engine light would stay on!usually hi way drive is a whole new emission game sensor work 100% different that city drive you have a O2 sensor problem don"t Get$$ the problem when if you say it only will do it on highway then take it on highway with OBD 2 in run scan mode have a passenger observe it this will give the the proper code you will need to peg it cheers!

Dec 27, 2008 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
2006 Mazda 6 Logo

256 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...