Question about Cars & Trucks

Open Question

Mass air flow meter citroen c4

Anti pollution warning on dash diagnostic fault codes shown are P0104 and P2566

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 335 Answers

SOURCE: 2001 mustang with code P0104 the scanner says that EGR flow

P0104 code is MAF or VAF. This can cause surging and rough running. If you disconnect the maf and find that it runs a little better, you can be sure that a maf replacement is in order. Double check the code by erasing it then roadtest. If code comes back then it is a hard code.

Posted on May 07, 2009

wyatt1582
  • 453 Answers

SOURCE: I have a 2001 mustang with a 3.8l I have a trouble code P0104

It is the DPFE sensor with out this your rpms will continue surge. Alot of people make the mistake of just replacing the EGR valve instead of the DPFE sensor which measures exhaust prssure going through the EGR vavle.

Posted on May 07, 2009

c1apton15
  • 3400 Answers

SOURCE: keeps on bringing up mass air flow meter during

Your MAF is either dirty/restricted or has totally gone bad. Another possibility is vac leak in intake hose to MAF

Posted on Mar 23, 2011

SOURCE: citroen c-crosser anti pollution warning light

We had this with our grand picasso all the warning lights on then car went into limp mode replaced two lambda sensor as this is what citroen thought it was in the end coolant sensor was leaking up wire back to ecu making all kinds of lights come on as it malfunctioned in the end new ecu cost over thousand pounds.

Posted on Aug 29, 2012

emissionwiz
  • 75051 Answers

SOURCE: citroen c crosser anti pollution light

Anti pollution light, I never heard of a Check engine light being called that.
Read on please.

Hello
When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

Posted on Nov 04, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is code PO104?


Best type in O.B.D engine fault codes PO104 it will come up with fault or faults it will point you in the right direction.

Jun 04, 2014 | 2008 Ford F-150

1 Answer

Depollution system faulty the engine is dead car want go


Is there any fault indication on the dash where the radio display is.
Anti pollution is basically citroens way of saying emissions system so it could be as simple as a loose emissions pipe but from what you say and the car does not run it could be your catalytic converter (part of the exhaust system) has failed causing the engine management system to cut in and protect the engine.
If there is no fault apart from anti pollution showing in the radio display find someone with a diagnostic machine to give you a better idea of the fault. Hope this helps a bit.

Apr 05, 2014 | 2006 Citroen C5 2.0i

1 Answer

Anti pollution system light came on when changed the alternator


Have someone read the codes. check for any damaged vacuum hoses or electrical connectors left unplugged

Apr 02, 2014 | 2009 Citroen C4 1.6i

1 Answer

Error Message "Anti Pollution System Faulty"


you need to take it to an a.s.e. certified mechanic and do an evap leakdown test to find out where the leak is in the evap system of your vehicle. replace the gas cap and see if the problem goes away as it is often the problem with this trouble code.

Dec 15, 2013 | 2006 Citroen C4 1.6i

1 Answer

I recently replaced the engine on my Citroen c4 2005 model, now the warning lights stay on, the engine overheat, abs and anti pollution warning lights stay on.


The problem for engine overheating rise due to insufficient refrigerant. Try recharging the refrigerant tank with fresh refrigerant and water. If the refrigerant in the tank is of poor quality then also engine overheat.

The reason for ABS light to come may be due to air in the brake fluid line. Try brake bleeding to remove the air bubbles. Also the faulty brake actuator line may cause the problem. Check for actuators on each wheel.

Pollution warning light comes on if the exhaust system not works properly. Check for faulty Oxygen sensor or faulty catalytic convertor.

Jul 10, 2013 | Cars & Trucks

1 Answer

Anti pollution fault


anti pollution fault with fault codes poo87 poo93 i changed fuel filter, so far all ok.

Jan 15, 2013 | 2009 Citroen Berlingo 1.9d

2 Answers

Anti pollution fault on my peugeot 308


my 2008 308 shows anti pollution fault,what do i do now.? any help please

Dec 23, 2012 | 2008 Peugeot 308 1.6

1 Answer

Citroen c crosser anti pollution light


Anti pollution light, I never heard of a Check engine light being called that.
Read on please.

Hello
When the service engine soon light (Also called the check engine light or engine management light) is turned on this is to alert you to the fact that Powertrain Control Module (computer) has detected a failure somewhere in the systems it controls you may not feel any difference in the way the engine runs, this can be the transmission or the engine or emission system, there are fault codes set in the modules memory for these faults. What needs to happen now is to have the powertrain control module scanned with a special tool called an OBD2 electronic engine control scanner or a OBD2 code reader. Once the code(s) are read then you must perform the diagnostics for each code and make the appropriate repairs based on the findings of the diagnosis that was performed, this is called doing "Pinpoint" testing.

Nov 04, 2012 | 2008 Citroen C-Crosser HDi

1 Answer

2006 range rover hse is displaying diagnostic code P0110, P0108, and P0104. What are they? Also, is there a place where I can get a list of all the codes?


try looking on directconnect file share and you can then download mine ,programme available for free download at sourceforge.net

P0110....Intake Air Temperature Circuit


P0108....Manifold Absolute Pressure/Barometric Pressure Circuit High Input


P0104....Mass or Volume Air Flow Circuit Intermittent

think this is telling you you need a new mass air flow sensor

Apr 06, 2011 | Land Rover Range Rover Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

192 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...