Question about BMW Cars & Trucks

Open Question

Crankshaft pulley removal bmw e91 diesel - BMW Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

freetek
  • 5568 Answers

SOURCE: broken crankshaft pulley bolt on

The only possibility I can suggest is that which is called and 'Easyout.' These are available at parts stores and come (normally) with a sized drill and a special bit with left-hand threads.
First a hole is drilled with the provided drill bit, then the removal bit is screwed into the new hole and turned counter-clockwise which further inserts the removal bit and, if the removal bit does not snap, the broken threaded shank should back out.
I would suggest soaking the broken part with penetrating lubricant first and allowing it time to seep into the threads of the broken bolt.   

Posted on Oct 13, 2008

csmock132
  • 4669 Answers

SOURCE: 1997 Bonneville - can't remove crankshaft pulley

You need a three jaw puller to remove the balancer. After you remove the center bolt the puller hooks into the three holes in the balancer.

Posted on Jun 08, 2009

  • 1 Answer

SOURCE: do not know how to remove crankshaft pulley to replace timeing belt

Ignore smart a$$ comments.
Disconnect negative battery terminal.
Remove front right wheel.
Remove splash guard.
Place jack under engine.
Remove left engine support bolts from body.
Remove engine support plate bolts from engine.
Unbolt air conditioner pump and move it out of the way.
Get under vehicle and remove steering pump bolts and move it out of the way.
Remove 6 crankshaft pulley bolts, should be 12mm.
The engine support bracket shoud come off now.
Remove the main crankshaft bolt.
Remove crankshaft dampener.
Remove the timing cover bolts and take off the covers.
Take off the old belt & replace with a new one, don't use a previously used belt.
Make sure the belt tensioner is installed correctly.
Put all the stuff back on.
Get a Haynes manual, pages 3-41.

Posted on Jul 06, 2009

ftw1952
  • 10319 Answers

SOURCE: I can't get the crankshaft damper pulley off.

Download this link and find your Service manual for your vehicle. It will serve you well and to keep for future reference

http://ezinearticles.com/?Find-the-Free-Auto-Repair-Manual-You-Need-Online&id=92717

Posted on May 02, 2010

  • 5 Answers

SOURCE: 2001 PT Cruiser: How too remove crankshaft pulley 2001 PT Cruiser...

GET A 3 SPOKE PULLEY EXTRACTOR AND SCREW IN THE BOLT BUT IN THE CRANKSHAFT HOLE PUT A MUCH SMALLER SCEW SO YOU WOUNT MESS THE INSIDE UP

Posted on May 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the crankshaft dumper pully?


Published: 11-May-2011
Engine - V8 4.4L Petrol - Crankshaft Pulley
In-vehicle Repair
Special Tool(s)

Holding Tool Crankshaft Pulley
303-893(LRT-12-080)
Adapter
303-191-03
Bolts and spacers
303-191-04
Remover, crankshaft pulley
303-588
Remover, crankshaft seal
303-D121
Installer, crankshaft seal
303-1100
Adapter - Crankshaft seal installer
303-1100-01 Removal
  1. Disconnect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).
  1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and support the vehicle.
  1. Remove the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).

  1. Remove the cooling fan shroud.
    • Release 2 clips from the cooling fan lower shroud.
    • Release and remove the cooling fan lower shroud from the cooling pack.

  1. Using the special tools, retain the crankshaft pulley.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. NOTE: The crankshaft pulley retaining bolt will be very tight.
    Remove the crankshaft pulley retaining bolt.
    • Discard the bolt.
  1. Remove the special tools.

  1. Using the special tools, remove the crankshaft pulley.
    • Collect the locking ring.
  1. Remove the special tools from the crankshaft pulley.

  1. Using the special tool, remove the crankshaft front seal.
    • Remove the outer section of the seal.
    • Repeat the process to remove the inner section of seal.
  1. Check the crankshaft damper pulley and locking ring for damage.
Installation
  1. Clean all the crankshaft pulley mating faces.

  1. Using the special tools, install the crankshaft front seal.
    • Lubricate the seal with clean engine oil.
    • Use the discarded crankshaft bolt with the service tool.
  1. Install the crankshaft pulley.
    • Lubricate the seal with clean engine oil.
  1. Install the crankshaft pulley locking ring.
  1. CAUTION: The screw thread in the crankshaft pulley must be cleaned out before installing a new crankshaft pulley bolt. Install, but do not tighten, the new crankshaft pulley bolt.
  1. CAUTION: Under no circumstances should the crankshaft setting peg, 303-645, be used in the following operations, to restrain the crankshaft. Using the special tools, retain the crankshaft pulley.
    • Tighten the crankshaft pulley bolt to 380 Nm (280 lb.ft).
  1. Remove the special tools.
  1. Install the cooling fan lower shroud.
  1. Install the accessory drive belt.
    For additional information, refer to: Accessory Drive Belt (303-05B Accessory Drive - V8 4.4L Petrol, Removal and Installation).
  1. Connect the battery ground cable.
    For additional information, refer to: Specifications (414-00 Battery and Charging System - General Information, Specifications).

Jan 27, 2016 | 2006 Land Rover Range Rover Sport

Tip

Changing a serpentine belt on an E36 BMW 318i(316i)


Remove the radiator cowling. It has 2 connecting clips(arrowed in photo)

b8bc03e.jpg


Remove these clips by pushing out the centre portion with a small screwdriver as shown below.

7a26c79.jpg

Lift the cowlin up and remove. Be careful of pushing it against the radiator fins.
Locate the A/C tensioner pulley on the righthand side of the enginebetween the A/C compressor and Crankshaft, and pry off the dust cover(arrowed) with a screwdriver.

3edfaf8.jpg

Loosen the 13mm nut inside and remove the belt.
Turn the 16mm bolt on the serpentine tensioner pulleycounter clockwise to slacken the belt and remove the belt. Refit the new belt to the routing diagram below and using the 1st track (closest to the engine) on the crankshaft
  1. Crankshaft
  2. Water pump/fan pulley
  3. Idler pulley
  4. Alternator
  5. Power steering
  6. Sepentine belt tensioner


9305b5b.jpg
If you are replacing the tensioner pulley remember that it is held in place by a reverse threaded bolt, so turn clockwise to loosen it.
Refit the A/C belt. fasten the tensioner pulley bolt by hand. Using a 10mm allen key in the hole in the pulley(arrowed), tension the belt, keep pressure on the allen key and fasten the pulley bolt with a wrench.
9b0a7ca.jpg
When refitting the fan shroud, position the shroud. It has a tab on each side halfway down the shroud that needs to locate in the radiator. Remove the centre pin from the shroud's clips completely. Insert the clip into its position and then insert the centre pin of the clip and push it in until flush with the clip itself.

on Oct 15, 2010 | BMW 318 Cars & Trucks

1 Answer

Nissan terrano 1996 2.7 diesel


The sensor is located behind the crank pulley/harmonic dampener. To replace:

1 Remove the tire/wheel and splash shield.
2 Remove the bolts, then loosen the mount bolt and pivot the side engine mount out of the way.
3 Loosen the idler pulley center nut and adjusting bolt, then remove the A/C compressor belt.
4 Loosen the alternator mounting bolt, nut and adjusting bolt, then remove the alternator belt.
5 Loosen the mounting nuts and adjusting nut, then remove the P/S pump belt.
6 Remove the dipstick and pipe.
7 Remove the crankshaft pulley.
8 Remove the upper covers and lower cover. NOTE: Do not use the upper and lower covers for storing removed items.
9 Remove the CKP sensor from the cylinder block.
10 Install the CKP sensor in reverse order of removal.

Feb 23, 2013 | Cars & Trucks

1 Answer

Timing marks trooper 1985 mod dlx turbo diesel


Refer to Figures 1,2,3,4 when performing 17-step timing procedure for 1981-1985 Diesel Engines.

Fig 1. Injection pump and camshaft alignment marks - Diesel engine.

archaeology_66.jpg


Fig 2. Removing the timing belt holder - Diesel engine.

archaeology_67.jpg

Fig 3. Injection pump alignment marks - Diesel engine.

archaeology_68.jpg

Fig 4. Tensioiner Pulley Bolt Sequence - Diesel engine.

archaeology_69.jpg

Procedure - Timing Belt replacement.

1. Disconnect the negative battery cable. Drain the cooling system.

CAUTION
When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze, and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.

2. Remove the timing belt cover. Remove the injection pump sprocket flange.

3. Using a prybar, remove the tension spring from the timing belt tensioner.

When removing the tension spring, avoid using excessive force for the spring may become distorted.

4. Remove the tensioner pulley bolt and the pulley.

5. Remove the timing belt and discard it.

To install:

6. Rotate the crankshaft to bring the No. 1 piston to TDC of the compression stroke.

7. Align the timing marks on the injection pump sprocket with the camshaft sprocket; the marks must be facing each other.

8. Using a new timing belt, install it in the following sequence: crankshaft sprocket, camshaft sprocket and the injection pump sprocket; the slack must be between the injection pump and camshaft sprockets.

9. Install the tension center and the tension pulley so the end of the tension center is fitted against both pins on the timing pulley housing.

10. Hand tighten the nut so the tension pulley can be rotated freely.

11. Install the tension spring and semi-tighten the pulley nut to 22-36 ft. lbs. (30-48 Nm).

12. Rotate the crankshaft 2 full turns clockwise to seat the belt and further turn the crankshaft 90° beyond TDC to settle the injection pump.

13. Loosen the tension pulley nut to take up the timing belt slack. Tighten the tension pulley nut to 79-94 ft. lbs. (108-128 Nm).

14. Install the injection pump sprocket flange; the hole in the outer circumference of the flange should be aligned with the triangular timing mark on the injection pump sprocket.

15. Rotate the crankshaft 2 full turns clockwise to bring the No. 1 piston to TDC of the compression stroke. Make sure the triangular timing mark on the timing sprocket is aligned with the hole in the flange, then, measure the timing belt tension; it should be 33-55 lbs.

16. Install the timing belt cover.

17. Connect the negative battery cable.

Jul 04, 2011 | 1995 Isuzu Trooper

2 Answers

Is the crankshaft pulley bolt left or right thread to undo diesel P38 engine


the bolt will turn opposite direction of your engines rotation. so if when setting the timing your manual tells you to crank your engine clockwise then you will need to rotate the bolt clockwise to remove it. you will need a huge belt wrench or a reverse socket in order to keep the engine and pulley from moving so you can crack the bolt. if the transmission is not attached to the engine at this point you may be able to use a crowbar to prevent the flywheel from turning and stop engine rotation that way. goodluck

Mar 27, 2011 | BMW 525 Cars & Trucks

1 Answer

Which way do u turn the harmonic balancer bolt to remove it


gas engine :counter clock wise use penetrating oil let soak lefty loosey Diesel Engines

The 2.2L diesel engine utilizes an exposed crankshaft pulley and a hidden crankshaft timing pulley/damper. The following procedure may be used to remove the exposed crankshaft pulley.

  1. Disconnect the negative battery cable.

  2. Loosen and remove the accessory drive belts.

  3. Turn the crankshaft pulley to align the timing mark with the engine pointer. This should be done if any further procedures are being performed which might disturb valve timing.

  4. Remove the retaining bolts, then remove the crankshaft pulley.

To install:

  1. Align and install the crankshaft pulley.

  2. Install the retaining bolts, then tighten to 10-17 ft. lbs. (14-23 Nm).

  3. Install the accessory drive belts, then properly adjust their tension.

  4. Connect the negative battery cable.

Dec 12, 2010 | 1994 Isuzu Rodeo

1 Answer

How to remove the harmonice balancer on a bmw 1.9 liter 4 cylinder engine. I can not turn the large bolt on the end of the crankshaft. Is it a left hand thread?


Welcome to FIxYa.com



Remove Harmonic Pulley



If necessary, remove drive belt and belt pulley for the air

conditioning compressor.

Remove drive Belt or alternator, refer to Drive Belts, Mounts,

Brackets and Accessories.

Attach Special Tool II 2 150 in conjunction with Special Tool il

2410.

Note:

Protect engine bracket from damage.

Insert wood between engine support and Special Tool 11 2

150.

Unscrew central bolt.

Replace crankshaft radial sealing ring, refer to Front Crankshaft

Seal, Service and Repair.

Installation:

Position the vibration damper in such a way that groove and

Woodruff key are aligned.

Replace central screw.

Tightening torque, refer to Engine. Specifications.





Thank you for using FixYa.com

Regards, Lee Davidian

Nov 24, 2010 | 1997 BMW Z3 Roadster

1 Answer

Bmw Crankshaft Pulley removal


there are special tool 11250 and 112410 mount on the hub to remove it

Feb 24, 2010 | 1999 BMW 328 Series

2 Answers

BMW X3 aircon belt problem--keeps jumping out of crakshaft pulley


if air con belt runs off the pulley inspect the crankshaft damper pulley, it may be broken!
the air cond belt is a stretch belt with no tensioner!

Jan 21, 2010 | 2005 BMW X5

1 Answer

Serpentine belt diagram for a 5.9 diesel with air and 9 pulleys


5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Sep 13, 2008 | 2008 Dodge Ram 3500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...