Question about Ford Cars & Trucks

1 Answer

1997ford eceno van shifter lock assembly electrical problem

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

I think the 15 amp fuse is blown. likely a short in the system. Look on top of the brake housing under the hood. There's a switch assembly with wires on top. Likely bad and brake fluid is leaking into switch and causing short. Replace. Hope that helps!

Posted on Nov 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key shifter lock


Yes, the shifter assemly has to be replaced. they are pricey but it does fix the problem. Also is very common in the newer Dodge magnums.

Jan 01, 2014 | 2003 Hummer H2

1 Answer

97 toyota corolla brake fuse continues to blow


more than likely you have a park lock solenoid problem , a lot of them are located on the shifter assembly or attached to a cable coming from the ignition when you press the brake pedal you can hear a click ," locate it" and disconnect the electrical connection to the solenoid

Nov 11, 2013 | 1994 Toyota Corolla

1 Answer

Where is neutral safty switch on 83 camaro z/28


Neutral Park/BackUp Lights Switch - REPLACEMENT & ADJUSTMENT
  1. Remove the console trim from the console.
  2. Disconnect the electrical connector from the switch.
  3. Remove the 2 attaching screws from the switch and remove the switch.
  1. To install a new switch:
    1. Place the switch onto the transmission control shifter and loosely install the attaching screws. Position the transmission control shifter assembly in the N notch in the detent plate.
    2. Assemble the switch to the transmission control shifter assembly by inserting the carrier tang into the hole in the shifter lever.
    3. Install the attaching screws and tighten.
    4. Move the transmission control shifter assembly out of N position. This will shear the switch internal plastic pin.

  2. To install the original switch:
    1. Place the switch onto the transmission control shifter and loosely install the attaching screws. Position the transmission control shifter assembly in the N notch in the detent plate.
    2. Rotate the switch on the shifter assembly to align the service adjustment hole with the carrier tang hole. Insert a 3 / 32 in. (2.38mm) diameter gauge pin to a depth of 9 / 16 in. (15mm) and tighten attaching screws.
    3. Remove the gauge pin.

  3. Connect the electrical connector to the switch.
  4. Install the console trim to the console.


490b67f.jpg

Fig. 1: Neutral start/back-up light switch



Hope this helps (remember to rate and comment this).

Sep 25, 2010 | 1983 Chevrolet Camaro

1 Answer

Steering wheel covers


I hope this helps....these are the steps to removing and replacing the cylinder:

  1. Remove the knee bolster.
  2. Remove the steering column trim covers from the steering column.
  3. Disconnect the steering column electrical connectors.
  4. Remove the wire harness assembly from the steering column and the wire harness strap.
  5. Slide the 2 connectors of the turn signal and multifunction switch assembly out of the bulkhead connector.
  6. Remove the key alarm connector from the lock module assembly in the following way:
  7. Rotate the key alarm connector 90 degrees.
  8. Pull the key alarm connector out of the lock module assembly.
  9. Remove the passkey connector from the lock module assembly.
  10. Remove the connector from the electric park lock, for vehicles equipped with floor shifters.
  11. Remove the ignition switch from the lock module using tool J42759 or equivalent.
To install:
  1. Install the ignition switch to the lock module
  2. Install the key alarm connector into the lock module assembly.
  3. Push the key alarm connector into the lock module assembly.
  4. Rotate the key alarm connector 90 degrees so that the key alarm connector locks into place.
  5. Install the passkey connector into the lock module assembly.
  6. Install the connector to the electric park lock, for vehicles equipped with floor shifters.
  7. Slide the 2 connectors of the turn signal and multifunction switch into the bulkhead connector.
  8. Attach the wire harness assembly to the steering column wire harness strap.
  9. Connect the steering column electrical connectors to the vehicle.
  10. Install the trim covers to the column.
  11. Install the knee bolster.
  12. Enable the SIR system.
  13. It may be necessary to reprogram the theft deterrent system if the module was replaced.

Mar 06, 2010 | 2001 Chevrolet Suburban

2 Answers

Got a 2000 chevy 3500 express van how do i get the old ignition switch out to replace it


remove the steering wheel , need a puller and locking ring tool, disconnect batt, turn the key to tho on position, and remove bolt that holds the tumbler in,

Nov 13, 2009 | 2000 Chevrolet 3500

1 Answer

Van won't lock into reverse or park all the time.


it is either the shifter or the cable, I would go with a broken part in the shifter linkage. Detrim the steering column and see what shows up, very easy just 4 screw I think.

Mar 19, 2009 | 1995 Ford Windstar

1 Answer

2008 Chevy Cobalt - care is running, but I can't turn it off! Go to park, try and move the key and it won't move to the off position to turn off the car


replace the shifter assembly.I replace alot of them.use this bulletin as a reference.Subject: Various Concerns With Shifter and/or Ignition Key (Replace Shifter Assembly/Shifter Components or Ignition Lock Cylinder )


Models: 2005-2008 Chevrolet Cobalt

2005-2006 Pontiac Pursuit (Canada Only)

2007 Pontiac G5

with Automatic Transmission 4T45-E (RPO MN5)

Some customers may comment on any of the following concerns:

• The shifter is hard to move or binds.

• They cannot remove the ignition key.

• It takes high effort to rotate the key.

Cause 1
The shifter button may be sticking in the handle.

Cause 2




The pin that activates the micro-switch may have moved out of position (refer to illustration above). This causes the micro-switch to fail to engage when the vehicle is placed in Park. If this condition is present, the customer will not be able to remove the key from the ignition.





The illustration above shows the switch in a correct position.

Cause 3
Metal flashing left in the cylinder may cause a high effort to rotate the key.

Cause 4
The slider may be binding in the guides. This may cause the shifter to become difficult to operate.

Correction 1
Verify that the shifter button is inoperative by evaluating if the park pawl pin on the shifter assembly moves when activating the button. If the parking pawl does not move when the button is activated, the shifter handle will have to be replaced. Refer to Floor Shifter Control Knob Replacement in SI.

Correction 2
Important: A change has been made to the shifter assembly for service. The replacement shifter assembly will read PRNDIL (Park, Reverse, Neutral, Drive, Intermediate and Low).

Verify that the micro switch is out of position. Replace the shifter assembly. Refer to Transmission Control Replacement in SI.

Correction 3
Important: Refer to instruction sheet that is supplied with the lock cylinder kit. BO 47869 is an essential staking tool and must be used for the repair.

Replace the ignition lock cylinder. Refer to Ignition Lock Cylinder Replacement in SI.

Correction 4
Replace the slide indicator and guides in the shifter following the procedure below:

Apply the parking brake.
Remove the upper console trim. Refer to Trim Plate Replacement-Console Front in SI.
Remove shifter knob. Refer to Floor Shifter Control Knob Replacement in SI.
Remove the indicator plate. Use a flat-bladed screwdriver to release the locking tabs.
Remove the shifter indicator lens.
Pull up on the indicator and remove it from the assembly.
Remove the two front rails by unsnapping the front and lifting up, and then back, to remove the rails from the shifter assembly.
Install the new guides. Place the hook end into the assembly and push down. It will snap into place.
Install the new slide indicator. With the transmission in neutral, place the slide over the shifter and into the guides. Move the slide indicator down the guides in the front and rear.
Important: Replace the shifter indicator lens if damage is present due to the slider binding or if it becomes damaged during disassembly.

Install the shift indicator lens.
Install the shift indicator plate.
Install the shifter knob. Refer to Floor Shifter Control Knob Replacement in SI.
Install the upper console trim. Refer to Trim Plate Replacement-Console Front in SI. post back with what you find.

Jan 20, 2009 | 2008 Chevrolet Cobalt

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...