Question about 2006 Hyundai Tucson

1 Answer

Reverse stop plate problem?

2006 Hyundai Tucson manual - reverse stop plate not limiting gear stick movement. When you try and select 1 st gear the stick travels all the way to the left and you get reverse gear. Any suggestions?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 40,784 Answers

IN the selector rails in the top section of the box there is a spring loaded de-dent ball that come into play when the lever is placed or pushed towards reverse. To select reverse you have to overcome this spring so that the selector rail can be moved. IF you can get a look at the top section of the box you may see a plug that is screwed in and facing the gear selector lever min the reverse position. If you can unscrew this plug there should be a spring and then a plunger of ball. I suspect that the spring may be broken or the plunger is stuck. If you can get to the gear lever pivot and remove it you will see the plunger that I am talking about . It should be in the removable top section

Posted on Nov 28, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Hyundai Coupe gearbox ( not car in product)

hi there! i was a master tech 4 hyundai, first of all has the atf fluid been changed and at the correct level. or have you had the multifuntion switch checked? please feel free to contact myself and i will advise you as required with my exsperience

many thanks

Dominic Hill

Posted on Dec 11, 2008

  • 750 Answers

SOURCE: Transmission: Reverse

check power going to reverse shift solynoid and check neutral switch

Posted on Sep 25, 2009

ghost45
  • 1280 Answers

SOURCE: vehicle wont change up into gear reverse gear not

P0734 - 4th gear incorrect ratio. P1529 Malfunction Indicator Lamp Request. Problem is in the transmission.
Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Posted on Oct 03, 2009

ghost45
  • 1280 Answers

SOURCE: 2001 Hyundai - reverse gear is inoperative. The

If I understand you correctly, you have ALL forward gears working, but reverse doesn't?... then the problem is in the transmission itself or the linkage on the trans linkage into reverse.

Posted on Oct 18, 2009

MauiRentaCar
  • 288 Answers

SOURCE: 2000 Hyundai elantra transmission delay, reverse going

Did you check the transmission fluid level? If necessary, add fluid. However you probably have a more serious problem. Take the car to a qualified transmission mechanic.

Posted on Feb 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No movement when put into gear.


automatic=check transmission oil in dip stick
check kick down cable if its detached from engine.
try reverse if nogood seek professional help

Apr 03, 2016 | 2006 Renault Megane 1.6

1 Answer

2006 diesel trajet, manual gearbox, all gears fine except reverse, hard to select at times, any ideas, please ??


Reverse syncro is going bad. Have lube changed and add Lucas trans fix . Might get lucky

Oct 07, 2015 | 2006 Hyundai Trajet 2.0

1 Answer

Car stars normally, the gear selector moves to P D R, but when given gas the car remains still w/engine running and revving. Dash shows car is in Drive or Reverse.


try to remove the positive cable from the battery and wait for 5 minutes then install back the positive cable. start the engine and try to engages the gears again

Sep 02, 2015 | 2006 Hyundai Tucson

3 Answers

I have a 2001 elantra. What would make it stay in reverse and 1st gear.it is a manual transmission


when you put it in reverse,first thing you feel a spring.after tthat you lift,
a security plate,this plate prevent you from going reverse into 1 gear.
cause the axel turn a little further when you allreddy has stop the car.
this takes two sec.thats why when putting it in reverse after you feel the spring you wait two seconds,then puch al the way in reverse.

Jul 26, 2014 | 2001 Hyundai Elantra

1 Answer

Manual gearbox linkage stuck in reverse, gear stick is limp


I would be looking at the selector cable ( if you have one ) for a broken cable or the end has come free of the selector . Should be under car but check both ends.

Jan 17, 2014 | Hyundai Cars & Trucks

1 Answer

When u come out reverse the gear stick goes stiff, hard to go back into first gear. been advised might be a pin, found piece of plastic under gear stick cover round shaped.


Hi,
Fiats do not enjoy a sound reputation for their transmissions. If you are confident in your skills, remove the cover / boot that surrounds the gear stick. and check it carefully for fitting into the housing. There may be a plastic of fibre cup that the ball of the gear stick rides in. depending on the locating device for this "bearing" will affect the movement of the gear stick. If you can lift the gearstick and it shows lots of slop, then the 'bushing is no longer holding the gearstick in the correct neutral position which enables each gear, including reverse, to be selected easily. The reason for the 'bushing' failing will have to be ascertained, it may be a simple fix, or it may be lots of aggravation, depending if the parts are all present and can be salvaged.

Good luck.

Feb 01, 2011 | 2006 Fiat 124

1 Answer

I have an automatic gas 2006 hyundai tucson. recently i noticed that when i engage the drive or reverse gear the vehicle lurches forward or backward accompanied by a banging noise. i have had both engine...


idle air control valve or iac same thing it controls idle speed yours is to high or you have a bad cv joint but i dnt think its that to new of car i would say your idle is to high

Apr 04, 2010 | 2006 Hyundai Tucson

1 Answer

I have a tucson premium 09 but on 10 plates only 400 miles on clock, and i have started to get bad smell of clutch burning when i drive along road, from cold in the morning or after stood for a while ,...


the bad smell you are getting is the manufacturers wax gassing of with the heat(newness)it will dissipate on a nice sunny day....if you are new to the "auto" 4wd system of hyundai then reverse is normal....the switch for 4wd only operates under 21mph.then it goes off on its own,above that speed.unless you are off road doing something silly.

Mar 22, 2010 | 2007 Hyundai Tucson Limited

1 Answer

I have a Volvo S40 2.0 diesel manual and have difficulty in selecting reverse gear from cold. The vehicle has done 36000 miles only


clutch hydraulics should be ok could be clutch plate sticking on input shaft splines i would drain and refill gearbox with correct grade of oil then try it try putting clutch down wait a few seconds before selecting reverse see if this helps you

Nov 09, 2009 | 2002 Volvo S40

Not finding what you are looking for?
2006 Hyundai Tucson Logo

174 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...